Induztr
Engineering Digest Document Viewer Related Models

1290 Infinity III Bio LC System Manual

Contents

  1. Overview pp. 5-6
    Product description and features of the 1290 Infinity III Bio LC
  2. Overview pp. 7-18
    Descriptions of Bio LC variants, detectors and level sensing
  3. Procedure pp. 19-25
    Installing modules, stack configuration and Flex Bench setup
  4. Procedure pp. 26-26
    Integrating the system into the network
  5. Procedure pp. 27-27
    Capillary and tubing connections in the flow path
  6. Procedure pp. 28-37
    Drain connectors, waste concept and leak sensor installation
  7. Procedure pp. 38-45
    LAN and instrument configuration, Lab Advisor and add-ons
  8. Procedure pp. 46-57
    Best practices, preparing a run and quick start steps
  9. Quality pp. 58-58
    InfinityLab LC performance check procedures
  10. Ordering pp. 59-63
    HPLC tool kit, heater devices and valve kits
  11. p. 33 table, 24 rows

Table 3: Compatibility of drain connectors and modules

Drain Connector TypeCompatible ModuleCompatible Module Type
DoubleG7116A/BColumn Compartment
SingleG7114A/BDetector
G7115A
G7117A/B/C
G7121A/B
G7123B
G7162A/B
G7165A
G7129A/B/CSampler
G7167A/B/C
G5668A
G7137A/B
G7157A
G4767A
G7122ADegasser
G7104A/CPump
G7110B
G7111A/B
G7112B
G7120A
G7131A/C
G7132A
G5654A
G4782A

Engineering Facts

14 facts · every claim linked to a page
Selection

The flow path is biocompatible, which preserves biomolecule integrity and reduces unwanted surface interaction.

Determines suitability for biopharma and biomolecule analysis.

Source
“Biocompatible solvent and sample flow path ensure integrity of biomolecules and minimize unwanted surface interaction.”
Selection

The system supports ultrahigh pressure up to 1300 bar and analytical flow rates up to 5 mL/min.

Defines the pressure and flow envelope for method and column selection.

Source
“Power range combines ultrahigh pressure up to 1300 bar and high analytical flow rates up to 5 mL/min for maximum UHPLC performance.”
Selection

The pump is biocompatible and designed for high-salt and extreme-pH biopharma applications.

Confirms compatibility with demanding mobile phases and salt-containing methods.

Source
“designed for use in biopharma and other applications utilizing high-salt and extreme-pH conditions”
Selection

The multisampler can inject at pressures up to 1300 bar and holds up to 6144 samples.

Sets sample capacity and pressure limits for high-throughput UHPLC work.

Source
“Injecting at pressures up to 1300 bar, the Bio Multisampler is a compact module with a capacity of up to 6144 samples”
Selection

The column thermostat cools to 20 °C below ambient and heats up to 110 °C.

Defines the usable column temperature range for method development.

Source
“cooling down to 20 °C below ambient temperature and heating up to 110 °C”
Performance

The 60 mm flow cell provides up to 10 times higher sensitivity than conventional flow cells.

Informs detector and flow cell selection for sensitive detection.

Source
“the 60 mm flow cell gives up to 10 times higher sensitivity than detectors with conventional flow cells”
Installation

Stacking modules in the prescribed configuration minimizes delay volume and optimizes the flow path.

Guides physical stack layout to achieve lowest dispersion.

Source
“These configurations optimize the system flow path, ensuring minimum delay volume.”
Installation

A single stack supports a maximum of four modules.

Determines whether a single-stack layout is feasible for the module count.

Source
“Single Stack (maximal 4 modules, in a bench rack or directly on the bench)”
Installation

Use two stacks to avoid excessive stack height when adding an extra detector.

Prevents unstable or overly tall stack configurations.

Source
“To avoid excessive height of the stack (for example when using the system in combination with an additional detector), it is recommended to form two stacks.”
Installation

The solvent cabinet holds a maximum of 8 L total, with no individual bottle exceeding 2 L.

Sets limits on solvent storage during installation.

Source
“The solvent cabinet is designed to store a maximum volume of 8 L solvent. The maximum volume for an individual bottle stored in the solvent cabinet should not exceed 2 L.”
Safety

The leak sensor stops the running system once the leak detection level is reached.

Explains automatic leak protection behavior during operation.

Source
“The leak sensor in the leak plane stops the running system as soon as the leak detection level is reached.”
Installation

Do not install drain connectors on the bottom module; connect its drain outlet to waste tubing instead.

Prevents incorrect drain connector installation and improper drainage.

Source
“Do not install drain connectors on the bottom modules of the stack. Drain outlet of the bottom module has to be connected via waste tubing to a suitable waste container”
Safety

DMF must not be used as mobile phase because it corrodes the PVDF leak sensor.

Avoids solvent-induced damage to the leak sensor.

Source
“Do not use DMF as mobile phase.”
Installation

LAN configuration must be done from the module with the highest data rate, usually the detector.

Ensures correct network integration of the system.

Source
“This must be the module (usually the detector) with the highest data rate.”