Operating instructions and tips for Agilent Captiva EMR—Lipid 96-Well Plate and 1 mL Cartridge Products
Technical Reference Summary
Covered Models & Document Scope
Covers Agilent Captiva EMR—Lipid products: 96-well plate (part numbers 5190-1000, 1 plate; 5190-1001, 5 plates) and 1 mL cartridge (part number 5190-1002, 100/pk).
Section-by-Section Technical Breakdown
pp. 2
Protein precipitation workflow
Describes the three-step workflow: add biological sample and crash solvent, mix to precipitate protein, and filter. It is highly recommended to add sample first and then crash solvent to achieve better sample homogeneity.
- Step 1: Add biological sample and crash solvent (sample first, then solvent).
- Step 2: Mix to precipitate protein; passive mixing (5 min) or active in-well mixing.
- Step 3: Filter; salts, proteins, lipids, and analyte are separated.
pp. 3
User Tips
Provides detailed recommendations for sample size, crash solvent composition and ratio, sample addition order, mixing options, and pass-through filtration/cleanup parameters including vacuum, pressure, flow rate, and centrifugation.
- Sample size between 20–200 µL.
- Crash solvent ratio between 3:1 and 5:1 ACN with 1% formic acid to sample.
- If total volume <500 µL, add 4:1 ACN:H2O to reach minimum 500 µL.
- ACN preferable to MeOH to maximize protein precipitation and avoid gelation.
- Recommended addition order: 1) Sample, 2) Crash solvent.
- Passive mixing: let stand 5 minutes.
- Active in-well mixing: pipette 3–5 cycles with wide-bore tips for >500 µL plates and 1 mL cartridges; vortex at 1,350 rpm for <500 µL plates.
- Vacuum 2–5 in Hg or positive pressure 3–4 psi initiates flow; controlled flow of one drop every 3–5 seconds recommended.
- After elution, apply higher vacuum/pressure for 1–2 minutes for maximum recovery.
- Centrifugation alternative: 500–800 rpm for minimum 10 minutes, then 2,500–3,000 rpm for 1–2 minutes to drain.
pp. 4
Ordering information
Lists part numbers and quantities for the Captiva EMR—Lipid 96-well plate and 1 mL cartridge products.
- 5190-1000: 96-well plate, 1 plate.
- 5190-1001: 96-well plate, 5 plates.
- 5190-1002: 1 mL cartridge, 100/pk.
Key Integration, Operating & Safety Requirements
| Specification / Condition | Engineering Implication | Applies To |
|---|---|---|
| Sample size should be between 20–200 µL. p.3 ↗ | Select sample volume within this range for optimal performance. | 96-well plate and 1 mL cartridge |
| Crash solvent ratio should be between 3:1 and 5:1 ACN with 1% formic acid to sample. p.3 ↗ | Use this ratio to ensure effective protein precipitation. | whole series |
| If total volume is less than 500 µL, add additional 4:1 ACN:H2O to reach a minimum volume of 500 µL. p.3 ↗ | Ensures sufficient volume for proper mixing and filtration. | whole series |
| ACN is preferable to MeOH to maximize protein precipitation and avoid gelation. p.3 ↗ | Choose acetonitrile over methanol as crash solvent. | whole series |
| Recommended sample addition order: 1) Sample, 2) Crash solvent. p.3 ↗ | Adding sample first improves homogeneity. | whole series |
| Passive mixing: let stand for 5 minutes. p.3 ↗ | Allows complete protein precipitation without active mixing. | whole series |
| For 96-well plates with <500 µL total volume, cap and vortex at 1,350 rpm. p.3 ↗ | Use vortex mixing for small volumes in plates. | 96-well plate |
| For 96-well plates >500 µL and 1 mL cartridges, pipette mix with wide-bore tips (3–5 cycles). p.3 ↗ | Use wide-bore tips to avoid shearing and ensure proper mixing. | 96-well plate >500 µL and 1 mL cartridge |
| Vacuum between 2–5 in Hg initiates flow; positive pressure 3–4 psi is also acceptable. p.3 ↗ | Set vacuum or pressure within these ranges for filtration. | whole series |
| For optimal lipid removal, use a controlled flow rate of one drop every 3–5 seconds. p.3 ↗ | Control flow to maximize lipid retention. | whole series |
| After elution, apply higher vacuum or positive pressure for 1–2 minutes to ensure maximum sample recovery. p.3 ↗ | Drying step improves recovery. | whole series |
| Centrifugation alternative for 96-well plates: 500–800 rpm for minimum 10 minutes, then 2,500–3,000 rpm for 1–2 minutes to drain. p.3 ↗ | Use centrifugation if vacuum/pressure not available. | 96-well plate |
| Protein precipitation and mixing can be performed in a separate tube, centrifuged, and transferred to the Captiva EMR—Lipid well/cartridge. p.3 ↗ | Provides an alternative workflow option. | whole series |
Technical Data
| Parameter | Value | Condition |
|---|---|---|
| Sample size | 20–200 µL p.3 ↗ | 96-well plate or 1 mL cartridge |
| Crash solvent ratio | 3:1 to 5:1 p.3 ↗ | ACN with 1% formic acid to sample |
| Minimum total volume | 500 µL p.3 ↗ | If total volume is less than 500 µL, add additional 4:1 ACN:H2O |
| Passive mixing time | 5 minutes p.3 ↗ | Option 1: Passive mixing |
| Vortex speed | 1,350 rpm p.3 ↗ | 96-well plates with <500 µL total volume |
| Pipette mixing cycles | 3 to 5 aspiration/dispense cycles p.3 ↗ | 96-well plates >500 µL total volume and 1 mL cartridges |
| Vacuum to initiate flow | 2–5 in Hg p.3 ↗ | |
| Positive pressure | 3–4 psi p.3 ↗ | Alternative to vacuum |
| Recommended flow rate | one drop every 3–5 seconds p.3 ↗ | For optimal lipid removal |
| Post-elution vacuum/pressure time | 1–2 minutes p.3 ↗ | To ensure maximum sample recovery |
| Centrifugation speed (initial) | 500–800 rpm p.3 ↗ | 96-well plates, minimum 10 minutes |
| Centrifugation time (initial) | minimum 10 minutes p.3 ↗ | 96-well plates |
| Centrifugation speed (drain) | 2,500–3,000 rpm p.3 ↗ | 96-well plates, 1–2 minutes to drain cartridge |
| Centrifugation time (drain) | 1–2 minutes p.3 ↗ | 96-well plates |