Agilent 6400 Series Triple Quadrupole LC/MS System Quick Start Guide
Technical Reference Summary
Covered Models & Document Scope
Covers the Agilent 6400 Series Triple Quadrupole LC/MS systems: 6410B, 6420A, 6430A, 6460A, 6460C, 6470A, 6490A, 6495A and 6495B. Data Acquisition software revision B.08.02 supports 6495B; B.08.01 supports 6410B, 6420A, 6430A, 6460A, 6460C, 6470A, 6490A and 6495A. Compatible LC modules: Agilent 1100, 1200, 1260 or 1290 Infinity, and 1260 Infinity II. MassHunter Workstation software includes Data Acquisition, Qualitative Analysis and Quantitative Analysis.
Section-by-Section Technical Breakdown
Describes starting the MassHunter Data Acquisition program and the eight main windows used to set up methods, run samples, monitor status and tune the instrument. It explains window show/hide behavior, status color-coding, and the roles of the Instrument Status, Actuals, Chromatogram Plot, Spectrum Plot, Method Editor, Sample Run, Worklist and Tune windows.
- Start Data Acquisition by double-clicking the desktop icon; on Windows 7 use Start > Agilent > MassHunter Workstation > Data Acquisition; on Windows 10 use the Windows icon > Agilent > Data Acquisition.
- If software engines need restarting, right-click the Acq System Launcher icon in the system tray and click Start Engines.
- Instrument Status window shows device states: Error, Not ready, Pre-run, Post-run, Running, Injecting, Idle, Offline, or Standby.
- Up to seven windows can be shown at once; windows can be floated by double-clicking the title bar and docked by double-clicking again.
- Press F1 on the active window to obtain help.
Covers switching the LC stream to waste, purging the LC pump, conditioning or equilibrating the column, setting up real-time actuals monitoring, and configuring real-time plot displays. The column can be conditioned while the Triple Quadrupole MS is tuned.
- Switch LC stream to Waste by right-clicking the QQQ device in the Instrument Status window and clicking LC > Waste.
- Purge the LC pump according to the pump User Guide.
- Type LC parameters and click Apply in the toolbar to download them to the LC.
- Set up Actuals monitoring via right-click > Setup; parameters outside entered limits are shown with a red background.
- Set up real-time plot displays by right-clicking the chromatogram plot and clicking Change.
Describes Checktune, Autotune and Manual Tune procedures, including expected run times, supported ionization sources per model, and corrective actions if Checktune fails. It also covers Fast Scan Autotune and the switch back to Acquisition context.
- Checktune takes approximately 3 minutes per polarity and evaluates whether MS parameters meet specified mass accuracy and resolution.
- Checktune can be run with ESI, AJS ESI and MMI sources.
- Autotune takes approximately 30 minutes per ionization mode for all models except 6490 and 6495, which take approximately 25 minutes per ionization mode.
- For all instruments except 6490 and 6495, Autotune can be run with AJS ESI and MMI sources; 6490 and 6495 Autotune only with AJS ESI.
- If Autotune fails, mark Start from Factory Defaults and rerun Autotune.
- Fast Scan Autotune is only supported on the 6490; Fast Scan acquisition is not supported on 6470 and 6495.
Explains creating and saving an acquisition method, entering LC and QQQ parameters, configuring scan segments, setting stored instrument curves, linking data analysis methods, and running interactive samples or worklists in locked or unlocked mode.
- Enter QQQ parameter values in the Time segments table; changing Scan Type clears the Scan segments table.
- For 6490 and 6495, fragmentor voltage cannot be set in Acquisition; the tune file value is always used.
- Add scan segments by right-clicking in the Scan segments section and clicking Add Row.
- Stored instrument curves set in the Instrument tab are displayed in the MS Actuals window of Qualitative Analysis.
- To run a Data Analysis method from the Sample Run window, select Both Acquisition and DA or DA Only and set Override DA method.
- Locked mode prevents changes to method or sample parameters during a run and prevents overwriting the data file in Data Acquisition.
Introduces the Qualitative Analysis Navigator and Workflows programs for reviewing acquisition method development results, selecting precursor and product ions, finding and identifying compounds, and molecular feature extraction. It also introduces the Quantitative Analysis program for batch quantitation, Batch-at-a-Glance review, and requantitation using outliers.
- Qualitative Analysis tasks include reviewing results for acquisition method development, selecting precursor and product ions for MRM, finding compounds, identifying compounds, and molecular feature extraction.
- Quantitative Analysis tasks include setting up a batch and method to automatically quantitate samples, reviewing Batch-at-a-Glance results, and identifying outliers to change the method and requantitate.
- Refer to the Qualitative Analysis and Quantitative Analysis Familiarization Guides and online Help for detailed operations.
Key Integration, Operating & Safety Requirements
| Specification / Condition | Engineering Implication | Applies To |
|---|---|---|
| Checktune takes approximately 3 minutes to run for each polarity. p.3 ↗ | Plan regular Checktune runs into instrument preparation time; a full two-polarity check requires about 6 minutes. | 6400 Series Triple Quadrupole LC/MS |
| Autotune takes approximately 30 minutes for each ionization mode for all models except the 6490 and 6495; the 6490 and 6495 take approximately 25 minutes per ionization mode. p.3 ↗ | Schedule Autotune only when necessary and allow sufficient time; 6490/6495 models are faster per ionization mode. | All models except 6490 and 6495; 6490 and 6495 |
| Checktune can be run with ESI, AJS ESI, and MMI sources. p.3 ↗ | Checktune is compatible with all three source types, allowing routine verification regardless of installed source. | 6400 Series Triple Quadrupole LC/MS |
| For all instruments except the 6490 and 6495, Autotune can be run with AJS ESI and MMI sources; with the 6490 and 6495, Autotune can only be run with the AJS ESI source. p.3 ↗ | 6490/6495 users must use the AJS ESI source for Autotune; MMI-based Autotune is not available on those models. | All models except 6490/6495; 6490 and 6495 |
| If Autotune fails, marking Start from Factory Defaults and clicking Autotune tunes the instrument starting from factory defaults, taking approximately 30 minutes per polarity for all models except 6490 and 6495, and approximately 25 minutes per ionization mode for 6490 and 6495. p.3 ↗ | Factory-default Autotune is a recovery path after failed Autotune; budget the same or slightly longer time. | 6400 Series Triple Quadrupole LC/MS |
| Fast Scan Autotune only tunes with Wide (1.2) resolution, Samples set to 1 on the Manual Tune > Acquisition tab, and step size 0.2. p.3 ↗ | Fast Scan acquisition requires these specific tune settings; scan time is generated automatically from step size and mass range. | 6490 Triple Quadrupole |
| Fast Scan acquisition is not supported for the 6470 and 6495; instead, faster scan rate is achieved by increasing the step size to 0.3 m/z. p.3 ↗ | 6470 and 6495 users should use step size 0.3 m/z for faster scanning rather than Fast Scan mode. | 6470 and 6495 |
| For 6490 and 6495 instruments, fragmentor voltage cannot be set in Acquisition; it always uses the value in the tune file. p.4 ↗ | Method development on 6490/6495 must control fragmentor via the tune file, not the acquisition method. | 6490 and 6495 |
| Up to 4000 MRM transitions can be monitored using Dynamic MRM. p.1 ↗ | Dynamic MRM enables large transition panels within a single acquisition method. | 6400 Series Triple Quadrupole LC/MS |
| The 6495B Triple Quadrupole is equipped with a gate valve for replacing hexabore capillaries during routine maintenance without breaking vacuum. p.2 ↗ | Hexabore capillary replacement on 6495B does not require venting the system, reducing maintenance downtime. | 6495B |
| The 6495, 6490, 6470, and 6460 Triple Quadrupole LC/MS instruments are shipped by default with the Agilent Jet Stream source using super-heated sheath gas to collimate the nebulizer spray. p.2 ↗ | These models default to AJS ESI source; method and tune development should account for AJS ESI as the standard source. | 6495, 6490, 6470, 6460 |
| The 6490 and 6495 include iFunnel Technology comprising the Dual Offset Ion Funnel, Agilent Jet Stream source, and a shorter desolvation assembly with Hexabore Capillary. p.1 ↗ | These models provide more efficient ion sampling; maintenance procedures differ due to the hexabore capillary and shorter desolvation assembly. | 6490 and 6495 |
| The System Logbook retention period can be set from 1 week to 1 year via Tools > Purge Settings. p.3 ↗ | Configure logbook purge settings to retain troubleshooting history for the desired audit or diagnostic period. | 6400 Series Triple Quadrupole LC/MS with MassHunter Data Acquisition |
| When Actuals monitoring limits are set, a parameter value outside the entered limits is shown with a red background. p.2 ↗ | Use Actuals range limits as a visual alarm for out-of-spec instrument parameters during runs. | 6400 Series Triple Quadrupole LC/MS |
| In locked mode, no one can change the method or sample parameters during a run, and the data file cannot be overwritten in the Data Acquisition program. p.4 ↗ | Use locked mode for regulated or unattended runs to protect method integrity and data files. | 6400 Series Triple Quadrupole LC/MS |
| Data Acquisition revision B.08.02 supports the 6495B, 6410B, 6420A, 6430A, 6460A, 6460C, 6470A, 6490A, and 6495A, the 1260 Infinity II LC system, Qualitative Analysis B.08.00, Quantitative Analysis B.08.00, and ECM 3.4.1 SP2 HF3 - HF4. p.2 ↗ | Verify software and firmware compatibility before upgrading; B.08.02 is required for 6495B support. | 6400 Series Triple Quadrupole LC/MS |
| Microsoft Windows 10 and Microsoft Windows 7 are supported. p.3 ↗ | Workstation PCs must run one of these operating systems for supported operation. | 6400 Series Triple Quadrupole LC/MS with MassHunter Data Acquisition B.08.02 |
Faults & Troubleshooting
| Code / Symptom | Possible Cause | Remedy | Note |
|---|---|---|---|
| Checktune fails p.19 ↗ | MS parameters outside limits for specified mass accuracy and resolution; failure may occur in MS1 or MS2. | Use Manual Tune tab: for MS1 failure, select Peak Width (Unit, Wide, or Widest) based on failed resolution and click Adjust Gain & Offset; for MS2 failure, do the same on the MS2 tab. If Adjust Gain and Offset passes, save the autotune file via Manual Tune > Files > Save, then click Autotune tab and Checktune. If Checktune fails again, run Autotune. | Step 3, page 19 |
| Autotune fails p.20 ↗ | Autotune could not achieve acceptable tune parameters. | Mark the Start from Factory Defaults check box and click Autotune to tune starting from factory defaults. Check the progress box in the lower right side of the Autotune tab for reasons why the tune failed; fix the problem or call the Agilent service engineer and provide this information. | Step 3, page 20 |
| Error (Instrument Status window device state) p.21 ↗ | Device error reported by the configured instrument device. | View logged events and errors in the System Logbook Viewer via the Log icon in the Data Acquisition toolbar, Tools > System Logbook Viewer, or the system taskbar LOG icon. | Step 3, page 21 |
| Not ready (Instrument Status window device state) p.10 ↗ | Device is not ready for acquisition. | Monitor device status in the Instrument Status window and review System Logbook for events and errors. | Step 1, page 10 |