Induztr
Engineering Digest Document Viewer Related Models

Agilent 7890B Gas Chromatograph Operation Manual

Technical Reference Summary

Covered Models & Document Scope

Agilent 7890B Gas Chromatograph (GC) standalone and data-system-controlled operation; covers keypad operation, methods and sequences, resource conservation (SLEEP/WAKE/CONDITION methods), Early Maintenance Feedback (EMF), GC/MS and GC/HS intelligent instrument features, configuration of inlets, detectors, columns, valves, PCM, aux EPC, barcode reader, and options. Manual part number G3430-90054, third edition October 2015.

Section-by-Section Technical Breakdown

pp. 18-20
GC Start-Up and Shutdown Procedures

Describes the sequence for starting up the GC, including checking gas source pressures, turning on gases and cryo coolant, powering the GC, installing and leak-checking the column, loading a method, and waiting for detector stabilization. Also gives procedures for short-term shutdown (less than a week) and long-term shutdown (more than a week), including temperature reduction, gas shutoff, column removal, and capping of fittings.

  • Start-up: check gas pressures, turn on carrier/detector gases and cryo coolant, power on, install column, leak-check, load method, wait for detector stabilization.
  • Short shutdown (<1 week): leave carrier gas on to protect column; reduce detector, inlet, and column temperatures to 150–200 °C.
  • Long shutdown (>1 week): load maintenance method (or set all heated zones to 40 °C), turn off main power, shut off all gas valves, remove and cap column, cap all fittings.
  • Never leave flammable gas flows on if the GC will be unmonitored.
pp. 21
Correcting Problems

Outlines the steps to take when the GC stops operation because of a fault: check the display and Status messages, stop the alert tone, resolve the problem, and then power cycle or toggle the affected component off and on. For shutdown errors, both actions are required.

  • Press [Status] and scroll to view additional messages.
  • Stop alert tone with [Off/No] or by turning off the offending component in the data system.
  • Resolve the problem (e.g., change gas cylinders, fix leak).
  • After fixing, power cycle the instrument or turn the problem component off then on; for shutdown errors do both.
pp. 23-32
Keypad Operation

Describes the function of the GC keypad keys, including run keys, component keys, status and info keys, general data entry keys, supporting keys, method storage and automation keys, and the Service Mode key. Explains keypad behavior when the GC is controlled by an Agilent data system, including remote lockout and available functions.

  • Component keys set temperature, pressure, flow, velocity, and other method parameters.
  • [Status] displays ready/not ready/fault information; blinking Not Ready LED indicates a fault.
  • [Info] provides context-sensitive help for the active parameter.
  • [Service Mode] accesses Early Maintenance Feedback setup and inlet leak checks; avoid service settings unless directed.
  • When controlled by a data system, keypad can view status, method settings, times, abort runs, and identify controlling computer.
pp. 33-35
GC Status, Alert Tones, and Logs

Explains the status board LEDs, alert tone patterns (single beep, series of warning beeps, continuous tone), blinking setpoint indications for shutdown conditions, and the three accessible logs: run log, maintenance log, and system event log.

  • Single beep: problem exists but run can proceed; warning disappears when run starts.
  • Series of warning beeps: more serious problem; beeps increase with persistence; component shuts down after a short time.
  • Continuous beep: hydrogen flow shutdown or thermal shutdown; press [Clear] to stop.
  • Blinking Off or On/Off on a parameter line indicates system shutdown of gas flow, multiposition valve, or oven.
  • Run log cleared at start of each run; maintenance log records EMF counter limit events; system event log records significant events.
pp. 38-46
Methods and Sequences

Defines what a method is, what settings are saved, the difference between active and stored methods, and how to create, load, and store methods. Covers method mismatch errors when hardware changes and the procedure to correct them on a standalone GC. Also describes programming sequences, priority sequences, ALS and valve subsequences, post-sequence events, and storing sequences.

  • Up to 9 user-created methods can be stored, plus SLEEP, WAKE, CONDITION, MS VENT, and a default method.
  • Loading a method immediately replaces active setpoints; Not Ready light stays lit until all settings are reached.
  • Method mismatch occurs for electronic devices (inlets, detectors, EPC modules) when hardware differs from saved configuration; correct by removing and installing the module via [Config] and [Mode/Type].
  • Sequences can specify up to five subsequences, priority (ALS only), and post-run sequences; stored as numbers 1–9.
  • Priority sequence can be activated at any time to interrupt a running sequence.
pp. 50-51
Running Methods and Sequences from the Keypad

Provides step-by-step instructions for manually injecting a sample, running a single ALS sample, aborting a method, and starting, pausing, resuming, and aborting sequences from the keypad.

  • Manual injection: load method, press [Prep Run], wait for Ready for Injection, inject and press [Start] simultaneously.
  • Single ALS sample: load vial, load method, press [Start] to initiate ALS cleaning, loading, and injection.
  • Abort a method with [Stop].
  • Start a sequence via [Seq Control], scroll to Start sequence, press [Enter]; Run LED lights.
pp. 106-116
Resource Conservation

Describes SLEEP, WAKE, and CONDITION methods used to conserve resources, and how to set the GC to conserve resources, edit an instrument schedule, create or edit sleep/wake/condition methods, and put the GC to sleep or wake it immediately.

  • SLEEP, WAKE, and CONDITION methods are specialized stored methods for resource conservation.
  • Instrument schedule can be edited to automate sleep/wake events.
  • Methods can be created or edited for sleep, wake, or condition.
pp. 118-128
Early Maintenance Feedback (EMF)

Explains EMF counter types, thresholds, default thresholds, available counters, and how to enable, change limits, disable, and reset EMF counters. Includes EMF counters for autosamplers and MS instruments.

  • EMF counters monitor component usage and trigger maintenance log entries when limits are reached.
  • Counters can be enabled, disabled, reset, and have limits changed.
  • Default thresholds are provided for various counters.
  • Separate counters exist for 7693A/7650 ALS with EMF-enabled firmware and earlier firmware.
pp. 130-137
Intelligent Instrument Features

Covers system-level communications for GC/MS and GC/HS systems, MS shutdown events, GC pressure shutdown events, setting up a vent method, manually preparing the GC for venting the MS, exiting the MS vent state, using the GC when the MS is shut down, enabling or disabling MS or HS communications, system EMF counters, and instrument schedule for an intelligent instrument system.

  • If not using flammable carrier gas, GC sets very low flows at each flow- or pressure-controlled device; e.g., purged union at 1.0 psi, inlet at 1.25 psi.
  • GC displays error state and logs events when MS is shut down; GC unusable until error cleared or MS unconfigured.
  • MS vent method: turn off MS transfer line heater and inlet heater, set oven <50 °C, set column flow to 15 mL/min for turbo pumps or 2 mL/min (never exceed 4 mL/min) for diffusion pumps.
  • GC pressure shutdown for carrier gas to MS transfer line also turns off MS transfer line.
pp. 140-187
Configuration

Describes how to configure GC resources, including assigning resources to devices, setting configuration properties, unlocking configuration, oven cryogenic cooling, inlet gas types and coolants, columns (including composite and LTM), cryo trap, heaters, detectors (makeup/reference gas, lit offset, FPD heaters, ignitor ignore), analog outputs, valve box, thermal aux, PCM, pressure aux, status, time, valves, injectors, sample tray, instrument, and barcode reader installation and use.

  • Configuration settings are stored with the method.
  • Use [Config] then component key to view current configuration.
  • Barcode reader can be used to scan configuration data (G3494A USB or G3494B RS-232).
  • Oven can be configured for cryogenic cooling.
  • Detector makeup/reference gas, lit offset, and FPD heaters are configurable.
pp. 189-199
Options

Covers instrument options including calibration (zeroing flow or pressure sensors, column calibration, hydrogen sensor calibration), communication (configuring IP address), and keyboard and display settings.

  • Flow and pressure sensors can be zeroed.
  • Column calibration and hydrogen sensor calibration are available.
  • IP address can be configured for the GC.
  • Keyboard and display options are accessible.

Key Integration, Operating & Safety Requirements

Specification / Condition Engineering Implication Applies To
Detector stabilization from a reduced temperature takes 2 hours for FID, TCD, and FPD, and 4 hours for uECD and NPD. p.18 ↗ Allow sufficient equilibration time before acquiring data; uECD and NPD require longer stabilization. 7890B GC with FID, TCD, uECD, FPD, NPD
Detector stabilization from detector off takes 4 hours for FID and TCD, 12 hours for FPD, and 18 to 24 hours for uECD and NPD. p.18 ↗ Turning off uECD or NPD requires a long stabilization period; plan shutdowns accordingly. 7890B GC with FID, TCD, uECD, FPD, NPD
For short shutdown (<1 week), leave carrier gas on to protect the column from atmospheric contamination and reduce detector, inlet, and column temperatures to between 150 and 200 °C. p.19 ↗ Maintains column integrity and reduces thermal cycling; do not turn off carrier gas. 7890B GC
For long shutdown (>1 week), set all heated zones to 40 °C if no maintenance method is available, turn off main power, shut off all gas valves, remove column and cap both ends, and cap all inlet/detector/external fittings. p.20 ↗ Prevents contamination and moisture ingress during extended idle periods. 7890B GC
A series of warning beeps sounds if the front inlet gas flow cannot reach setpoint; the flow shuts down after 2 minutes. p.12 ↗ Investigate flow restrictions or leaks promptly; shutdown occurs automatically after 2 minutes. 7890B GC
A continuous beep sounds if a hydrogen flow is shut down or a thermal shutdown occurs; press [Clear] to stop the beep. p.13 ↗ Continuous tone indicates a safety-critical condition; investigate hydrogen shutdown cause before resuming. 7890B GC
Up to 9 user-created methods can be stored in the GC, along with one SLEEP, one WAKE, one CONDITION, an MS VENT, and a default method. p.39 ↗ Plan method numbering and storage; specialized methods occupy dedicated slots. 7890B GC standalone
Method mismatch occurs only for electronic devices (inlets, detectors, EPC modules), not for consumables such as columns, liners, and syringes. p.42 ↗ Hardware changes to electronic modules require reconfiguration to avoid method load errors. 7890B GC standalone
To correct a method mismatch, remove the module via [Config][hardware module] > [Mode/Type] > Remove module, power off, change hardware, power on, install module via [Config][hardware module] > [Mode/Type] > Install module, then save the corrected method. p.42 ↗ Following this procedure prevents method mismatch errors after hardware replacement. 7890B GC standalone
A sequence can specify up to five subsequences, plus priority (ALS only) and post-run sequences, and is stored as a number from 1 to 9. p.51 ↗ Complex automation can be programmed; priority sequence allows interruption without editing. 7890B GC
For MS vent method with turbo pumps, set column flow to 15 mL/min or maximum possible; rates above 15 mL/min may not provide additional benefits. For diffusion pumps, set flow to 2 mL/min and never exceed 4 mL/min. p.132 ↗ Protects MS pump and ensures safe venting; observe flow limits. 7890B GC configured with MS
If not using flammable carrier gas, the GC sets very low flows at each flow- or pressure-controlled device; for a purged union at the transfer line, pressure is set to 1.0 psi and inlet pressure to 1.25 psi. p.132 ↗ These low pressures are normal during MS shutdown/vent states; do not misinterpret as faults. 7890B GC with MS
When an Agilent data system controls the GC, the keypad can be locked to prevent setpoint changes; the Remote LED is lit. p.31 ↗ Operators must use the data system for method changes when keypad is locked. 7890B GC with data system
Pressing [Stop] during a GC run immediately ends the run; the data system may retain collected data but no further data is collected for that sample. p.31 ↗ Use [Stop] only when necessary; partial data may be available. 7890B GC
The Service Mode key accesses Early Maintenance Feedback setup and inlet leak checks, and also service personnel settings that can cause problems if misused. p.32 ↗ Avoid service settings unless specifically directed; use for EMF and leak checks only. 7890B GC
The run log is cleared at the start of each new run and lists any deviations from the planned method, including keypad intervention. p.35 ↗ Run log provides traceability for method deviations; review for GLP compliance. 7890B GC
The maintenance log records entries when user-defined component counters reach a monitored limit, including counter description, current value, monitored limits, and which limit was reached. p.35 ↗ Use maintenance log to track consumable usage and schedule maintenance. 7890B GC
When configured for enhanced GC-MS or GC-HS communications, the GC displays error messages from connected instruments; check the connected MS or HS for more information. p.34 ↗ Troubleshooting may require checking both GC and connected instrument. 7890B GC with MS or HS
If a shutdown includes safety concerns, such as hydrogen carrier gas flow shutdown, you must power cycle the GC. p.34 ↗ Power cycling is required to clear safety-related shutdowns; investigate cause before resuming. 7890B GC
The GC can store up to 31 keystrokes as a macro using [Prog] and [User Key 1] or [User Key 2]. p.30 ↗ Frequently used key sequences can be automated for efficiency. 7890B GC

Faults & Troubleshooting

Code / Symptom Possible Cause Remedy Note
Front inlet flow shutdown p.12 ↗ Front inlet gas flow cannot reach setpoint. Press [Off/No] to stop the beeping; resolve the problem (e.g., check gas supply, leaks, restrictions). Message briefly displayed; flow shuts down after 2 minutes.
Continuous beep p.13 ↗ Hydrogen flow is shut down or a thermal shutdown occurs. Press [Clear] to stop the beep; investigate and resolve the cause of the hydrogen shutdown or thermal shutdown before resuming. See Hydrogen Shutdown in the Troubleshooting manual.
Off or On/Off blinking on component parameter line p.34 ↗ System has shut down a gas flow, multiposition valve, or the oven. Go to the blinking parameter, press [Off/No] to clear the fault, resolve the problem if possible, then press [On/Yes] to use it again. If problem not fixed, fault will recur. For safety-related shutdowns (e.g., hydrogen carrier gas flow), power cycle the GC.
Detector On/Off line blinking p.34 ↗ Detector pneumatics shutdown or failure in another part of the detector. Go to the blinking parameter, press [Off/No] to clear the fault, resolve the problem, then press [On/Yes] to use it again.
Not Ready LED blinking p.26 ↗ A fault has occurred. Press [Status] to see which parameters are not ready and what fault has occurred.
Method and hardware do not match (error message) p.41 ↗ Actual hardware no longer matches hardware configuration saved in the method (e.g., FID replaced by TCD). Remove module via [Config][hardware module] > [Mode/Type] > Remove module, power off, change hardware, power on, install module via [Config][hardware module] > [Mode/Type] > Install module, then save corrected method. Applies to standalone GC; method mismatch occurs only for electronic devices.
GC displays error state and logs events; GC not usable p.132 ↗ MS is shut down or communications lost. Clear error state or unconfigure MS from GC; GC automatically clears error when MS repaired or communications restored. See 'To Use the GC When the MS is Shut Down'.

Technical Data

Parameter Value Condition
Detector stabilization time from reduced temperature 2 hours p.18 ↗ FID
Detector stabilization time from detector off 4 hours p.18 ↗ FID
Detector stabilization time from reduced temperature 2 hours p.18 ↗ TCD
Detector stabilization time from detector off 4 hours p.18 ↗ TCD
Detector stabilization time from reduced temperature 4 hours p.18 ↗ uECD
Detector stabilization time from detector off 18 to 24 hours p.18 ↗ uECD
Detector stabilization time from reduced temperature 2 hours p.18 ↗ FPD
Detector stabilization time from detector off 12 hours p.18 ↗ FPD
Detector stabilization time from reduced temperature 4 hours p.18 ↗ NPD
Detector stabilization time from detector off 18 to 24 hours p.18 ↗ NPD