Induztr
Engineering Digest Document Viewer Related Models

A 3004 H/X — instruction manual a 2504 xn a 3004 xn

Technical Reference Summary

Covered Models & Document Scope

Pfeiffer Vacuum A 2504 / A 3004 multi-stage Roots pumps (dry pumps for harsh applications), software V.3.04 and higher. Variants: H (harsh), X (corrosive), XN (very corrosive) versions. Part number matrix F4{H|X|N}b7cSSg6i01l0 encodes model (A 2504=J, A 3004=I), voltage (low/high voltage 60 Hz), exhaust (check valve or SEPM check valve), and 'c' depends on customer configuration. Options: temperature management STD/EHT/ELT, SEPM, SEMI, IHN (Internal Hot Nitrogen), V-Box.

Section-by-Section Technical Breakdown

pp. 18-21
Product Description and HHR Remote Control

Identifies product versions (A 2504H/X/XN, A 3004H/X/XN), scope of delivery, HMI components and connectors (J1–J8, S1, S2), and the Hand-Held Remote control keys and display elements.

  • Delivery includes: pump, EMS cover plug, water connectors (2), nitrogen connector, electrical connector, HHR + cable, manual, oil can(s)
  • HHR indicators: green = running, yellow = warning, red = alarm
  • HHR keys: CONT., ROOTS, PURGE, AUX, START/STOP plus menu navigation keys
  • Display option indicators: R (Roots), P (purge), H (IHN), S (stand-by purge), I (manual inlet valve)
  • Keypad membrane: never use pointed objects
pp. 22-31
Installation and Commissioning

Horizontal installation with vertical pumping axis, inlet on top; seismic anchoring with brackets torqued to 62 N·m; oil filling (1.21 L total per pump); water and nitrogen circuit connection; pumping line connection; leak tightness check; electrical connection; first-time start-up and rotation direction check.

  • Seismic bracket bolts/scres torque: 62 N·m (all steps)
  • Oil capacity per pump (A 2504 & A 3004): FB 0.28 L, Roots gear side 0.55 L, Roots motor side 0.38 L, total 1.21 L; fill to mid-point of sight glass
  • Water circuit: female connector IN, male OUT; max pressure 101 psi (7 bar); use regulated water, softened/non-aggressive recommended
  • Nitrogen tubing: 6 mm OD / 4 mm ID; flow display guaranteed up to 120 slm, above that only indicative
  • Close nitrogen pressure regulator (turn knob counter-clockwise) before pressurizing to avoid internal damage
  • Inlet parts must withstand negative pressure of 1·10⁻³ hPa absolute
  • Use flexible tubes to reduce vibration transmission; make inlet line short/straight, diameter ≥ pump inlet flange ID
  • Cover venting: 50 mm diameter nozzle with differential pressure sensor; exhaust box must be connected
pp. 32-36
Operation

Powering on/off, pumping start-up and shutdown, auto-restart configuration, Roots control option, emergency stop and restart, prolonged stoppage, use of two remote controls, operation monitoring and configuration saving.

  • HHR control mode selected via [DEFINITION][CONTROL MODE][HHR]
  • ROOTS/PURGE/AUX keys operate locally only when the corresponding [DEFINITION] command is [ENABLED]
  • Auto-restart configurable after power loss or fault conditions
pp. 37-49
Advanced Settings

Configuration of nitrogen injection (management mode, flow fault, purge prolongation), IHN hot nitrogen with temperature regulation, exhaust pressure monitoring (SEPM), water circuit description, FB/Roots temperature regulation, pump heating, inlet isolation valve management, motor power/rotation frequency monitoring, seizing detection, IDLE mode, analog/logic inputs, SEMI pump configuration.

  • Nitrogen flow fault indication with interlock capability
  • IHN temperature regulation via dedicated option
  • SEPM (Silencer Exhaust Pressure Measurement) monitors exhaust pressure with warning/alarm levels
  • Management of inlet isolation valve via connector J4
  • Monitoring of motor power, rotation frequency and seizing
  • IDLE mode operating principle for reduced operation
pp. 50-65
Interfaces for Control

Control modes: HHR remote, J1 REMOTE connector, J3 user connector, J4 isolation valve connector, J5 Roots connector, plus emergency stop command wiring.

  • J1: REMOTE control connector
  • J2: RS-232, J6: RS-232/RS-485, J7: RS-485 serial links
  • J4: inlet isolation valve control
  • J5: Roots 2 control
  • Emergency stop via dedicated EMS connector; certain components stay live between connector and breaker when stopped
pp. 66-72
Maintenance and Decommissioning

Safety instructions, maintenance frequency, on-site maintenance, freeing up the functional block, exchange procedure for replacement product (disconnect, drain water circuit, prepare for shipping), prolonged shutdown and recommissioning, disposal.

  • Drain the water circuit before disconnecting/shipping
  • Never store a used pump – return to service center
  • Free up the functional block procedure for maintenance
pp. 73-81
Malfunctions and Fault Indication

Fault message tables and troubleshooting: pump/Roots fails to start; pump running with HHR fault message; pump runs but performance inadequate.

  • Faults displayed via HHR with warning (yellow) / alarm (red) indicators
  • Troubleshooting split into: no-start, running-with-fault, inadequate-performance
pp. 85-92
Technical Data and Dimensions

General, technical, environmental, cooling water, nitrogen, and electrical characteristics, dimensions, weight distribution/center of gravity and required maintenance space. Appendix covers electrical component locations, circuit breaker adjustment, and monitoring sensor locations.

  • Mains voltage ranges: 200–230 V and 380–480 V, 50/60 Hz, three phases, four wires
  • Example rating plate: SCCR 10 kA, 25 A full load current
  • Pump weight ~250 kg (rating plate example); weight/center of gravity vary by model
  • Appendix includes circuit breaker adjustment and monitoring sensor locations

Key Integration, Operating & Safety Requirements

Specification / Condition Engineering Implication Applies To
Total oil fill per pump is 1.21 L (FB 0.28 L, Roots gear side 0.55 L, Roots motor side 0.38 L), identical for A 2504 and A 3004. p.23 ↗ Order correct Pfeiffer Vacuum oil (A113) and fill each housing to mid-sight-glass; only manufacturer's oil is allowed. A 2504 and A 3004 all variants
Ships WITHOUT oil – filling is mandatory before first start (label: 'ROOTS PUMP SHIPPED WITHOUT OIL'). p.8 ↗ Do not power on before completing oil fill; damage otherwise. whole series
Seismic bracket and reinforcing rail bolts must be torqued to 62 N·m. p.22 ↗ For seismic installations, customer supplies floor bolts; use this torque on all three bracket attachment steps. whole series, seismic option
Water circuit maximum pressure label: 101 psi (7 bar). p.7 ↗ Cooling water supply must be regulated and below 7 bar; use softened/non-aggressive water and inlet filter if solid pollution exceeds spec. whole series
Nitrogen connection uses 6 mm OD / 4 mm ID tubing; displayed flow value is guaranteed only up to 120 slm. p.25 ↗ Size nitrogen supply lines accordingly; treat HHR flow readings above 120 slm as indicative only. whole series
Manual shutoff valves on water and nitrogen supply must be installed within 3 m of the pump. p.11 ↗ Plan plant layout and LO/TO points accordingly before installation. whole series
Pumps are shipped pressurized with nitrogen and sealed; for storage after unsealing, pressurize to 200 hPa relative pressure. p.16 ↗ Keep blanking plates on until connected to pumping line; use 200 hPa N₂ for storage up to 1 year. whole series
Connected inlet-side chambers must withstand negative pressure of 1·10⁻³ hPa absolute. p.27 ↗ Verify upstream chamber/vessel integrity before evacuation. whole series
Cover venting nozzle diameter: 50 mm, with differential pressure sensor; exhaust box required for proper venting. p.27 ↗ Exhaust extraction must generate sufficient differential pressure per SEMI configuration; include exhaust box in line design. SEMI-configured pumps
LEL detection in extraction system must trigger gas shutoff at 25% LEL; oxidizer concentration must not exceed 60% of MOC (NFPA 69-2019 §7.7.2.5). p.12 ↗ Mandatory interlock design for flammable/pyrophoric processes; risk assessment per EN 50495 required from user/integrator. whole series in flammable/pyrophoric service
Mains supply: 200–230 V or 380–480 V, 50/60 Hz, three-phase four-wire; example SCCR 10 kA, 25 A full-load current. p.7 ↗ Verify facility supply and breaker ratings (SCCR ≥ available fault current) before connection. whole series, per voltage variant (low/high voltage)
Software version must be V.3.04 or higher for this manual to apply. p.6 ↗ Check firmware version before using documented settings/options. whole series
Emergency stop stoppage: components between electrical connector and breaker remain energized. p.11 ↗ Mains disconnect must remain visible and accessible; LO/TO required before any electrical work. whole series
Pump must operate horizontal, on its feet (not casters), pumping axis vertical, inlet on top. p.22 ↗ Check with spirit level and lower feet onto floor; do not leave load on casters during operation. whole series
XN versions are classified dual-use goods (Category 2B350i, EC regulation 428/2009). p.13 ↗ Export/import licenses may be required for international shipment of very-corrosive variants. XN variants only
Options available at ordering: temperature management STD/EHT/ELT, SEPM, SEMI, IHN, V-Box; part-number matrix F4[H|X|N]b7cSSg6i01l0; not all option combinations available. p.6 ↗ Decode and order via the matrix in §1.1.2; verify option availability with Pfeiffer Vacuum before specifying. whole series
Pump weight approximately 250 kg (rating plate example); casters for short moves only; lifting device required for hoisting via rings. p.8 ↗ Do not handle manually; plan forklift/crane access and floor loading per weight distribution chapter. whole series (weight varies by model)
Blasting plates' stock O-rings are not compatible with all applications; user/integrator must supply compatible O-rings. p.27 ↗ Replace sealing O-rings to match process chemistry when connecting pumping line. whole series
An interlock must stop process gas flow if nitrogen purge flow is interrupted. p.25 ↗ Wire 'purge flow fault' signal to process gas supply shutoff; required for pyrophoric service. whole series in pyrophoric service
Pump exhaust must always be connected to a dangerous-gas extraction system; exhaust line components must be rated above maximum pump-generated pressure. p.26 ↗ Verify exhaust component pressure ratings and leak-test the line after installation. whole series