OmniStar — instruction manual gsd 350 thermostar 1st generation
Technical Reference Summary
Covered Models & Document Scope
Pfeiffer Vacuum GSD 350 gas analysis system operating instructions covering OmniStar (PT Q8...) and ThermoStar (PT Q9...) variants. Variants include standard vs. corrosive gas versions (suffix C), Ir-Y2O3 or W filaments, with/without calibration unit, mass ranges 100/200/300 u, stainless steel (OmniStar, 1/2 m capillary, 200/350 °C heating) or quartz (ThermoStar, 1/2 m capillary, 200/350 °C heating) gas inlets, and with/without 7" display. Example part number PT Q80 217 110 = OmniStar standard, Ir-Y2O3 filament, 1 m stainless steel capillary with 200 °C heating, 100 u, with display.
Section-by-Section Technical Breakdown
Safety instructions across the product life cycle (transport, installation, operation, maintenance, shipping, disposal) with DANGER/ WARNING/CAUTION/NOTICE levels. Defines permissible ambient conditions, proper use, foreseeable misuse and personnel qualification levels 1-3.
- Unit weighs up to 26 kg depending on version; lifting requires 2 persons
- Hot surfaces > 50 °C on heating components and gas inlet during operation — burn hazard, EN 420 gloves required
- Not ATEX-approved; operation in explosive atmospheres is foreseeable misuse
- Proper use: analysis of non-corrosive, non-flammable gases; corrosive gas version for specific corrosive applications
- Mains cables must meet double isolation per IEC 61010 / IEC 60950; 3-pin cable with protective earth; connect mains before all other cables
- Keep lines and cables away from surfaces > 70 °C; provide touch protection above 70 °C
- Maintenance level 1: trained specialist; level 2: technically educated customer or PV service; level 3: customer with PV service training
The GSD 350 reduces sample gas pressure from 1000 hPa to PrismaPro working pressure via a pressure reduction stage and analyzes gas components by mass/charge ratio with the QMA 250 M quadrupole. Describes gas inlet systems, calibration unit, vacuum systems, sealing gas system (corrosive version), heating units and electronic components.
- Sample gas flow through capillary: 1–2 sccm
- Turbopump (SplitFlow principle) maintains operating pressure < 5×10⁻⁵ hPa in vacuum chamber with gas inlet open
- ThermoStar quartz capillary ends 1–2 mm in front of the orifice so reactive gases avoid wall contact
- Calibration unit calibrates mass scale, sensitivity and resolution in high mass range (> 200 u) using PFTBA; PFTBA persists in background signal — baking out after calibration recommended
- Total pressure gauge covers 1000 hPa to 5×10⁻⁹ hPa
- Heating units: capillary 200 °C or 350 °C version (adjustable 80 °C to max, default 120 °C), gas inlet heating max 100 °C (automatic), vacuum chamber 100–130 °C
- Sealing gas: major portion ~300 sccm flows to exhaust gas connection; sealing gas dilutes inlet gas concentrations by factor > 100
- Electronics: QME 250 analyzer electronics, TC 110 turbopump drive, power supply pack, mainboard, PoE injector, 7" touch display
Covers venting, exhaust gas and sealing gas hose connection, capillary installation, Ethernet/network setup including IP address configuration, functional earth and mains connection, and PV MassSpec software installation. Interface chapter defines USER IO, AUX IO, Ethernet and mains connections.
- Connection panel: AUX IO, USER IO, Ethernet RJ-45, sealing gas connection, exhaust gas connection, mains with power switch, grounding connection
- IP address of GSD 350 and host computer can be changed; sub-network examples provided
- Mains connection via IEC 320 C13 socket
- Exhaust gas hose must be trimmed and connected; no overpressure permitted at exhaust gas connection
Switching on the unit and starting the pumping system; operation via the 7" touch display with Dashboard, Info, Settings, Messages, Control and Measurement menus. Settings include measurement recipes, heating, sensors, language, autostart, network and GSD system parameters.
- Control menu functions: pump down, vent, heating on/off, gas inlet valve open/close (OmniStar), bake-out, emission on/off, electron multiplier on/off, calibration valve open/close
- Measurement modes: Spectrum Scan and Selected Masses recipes
- Factory settings reset available; warning/fault messages shown via warning triangle and Messages menu
- Version without display: controlled exclusively via web interface; LEDs for Power, Vacuum+Ready, Error, Heater, Filament, Purge
Maintenance intervals and procedures for the basic unit, high vacuum and fore-vacuum systems, gas analysis unit, gas inlet systems of both versions, capillaries, heating units, electronic components, calibration unit and corrosive-gas-specific parts. Includes component replacement (diaphragm pump diaphragm, turbopump operating fluid, orifice, capillaries, QME 250, mainboard, etc.).
- Capillary servicing: stainless steel capillaries can be notched/snapped and shortened with clamping collar fittings; quartz capillary trimmed by notching/snapping (eye protection required)
- Gas inlet maintenance includes orifice and interior gas guide replacement
- Calibration unit: refilling with PFTBA calibration medium, calibration valve replacement
- Corrosive gas version extras: sealing gas valve, manual and digital pressure regulator replacement
- Fan protection screens and housing parts cleaning procedures defined
Troubleshooting table for fault diagnosis, instructions for shipping (decontamination of contaminated products required), disposal of the gas analysis system, Pfeiffer Vacuum service offerings, spare parts list, special tools and accessories ordering information.
- Special tool PV M40 813 wrench for turbopump housing cover
- Accessories include capillary hose adapter; ordering via Pfeiffer Vacuum
- Contaminated devices must be decontaminated before shipping/maintenance/disposal
General technical data, unit conversion tables for pressure and gas throughput, and dimensional drawings of the GSD 350.
- Permissible ambient conditions: indoor, max altitude 2000 m, 10–40 °C, IP30, protection class I, overvoltage category II, pollution degree 2, rel. humidity max 80% at <31 °C / 50% at <40 °C
- Pressure unit conversion table (hPa/mbar/Torr) and gas throughput units (sccm, slpm)
- Dimensions in mm shown in Fig. 69
Key Integration, Operating & Safety Requirements
| Specification / Condition | Engineering Implication | Applies To |
|---|---|---|
| Sample gas flow through the capillary is 1–2 sccm with gas inlet open p.26 ↗ | Process side load is minimal; sample extraction won't disturb the process, but supply pressure must stay within the pressure-reduction stage design (1000 hPa inlet) | Whole series |
| Turbopump maintains operating pressure < 5×10⁻⁵ hPa in the vacuum chamber with gas inlet open p.27 ↗ | Defines expected analyzer background conditions; higher pressures indicate blockage or pump degradation | Whole series |
| Capillary dimensions: stainless steel OD 1/16" / ID 0.15 mm (OmniStar); quartz OD 0.23 mm / ID 0.15 mm (ThermoStar) p.11 ↗ | Determines replacement capillary specs and conductance; quartz version is required for reactive gas analysis without wall contact | OmniStar vs ThermoStar respectively |
| Capillary heating adjustable 80–200 °C (200 °C variant) or 80–350 °C (350 °C variant); standard setpoint 120 °C; gas inlet heating max 100 °C (automatic); vacuum chamber heating 100–130 °C p.29 ↗ | Set heating above the dew point of condensable sample components; gas inlet heating cannot be set manually and switches parallel to capillary heating | Whole series; 350 °C heating is an option |
| Total pressure gauge measures 1000 hPa down to 5×10⁻⁹ hPa on the vacuum chamber p.28 ↗ | Continuous chamber pressure monitoring available on display and PV MassSpec without extra instrumentation | Whole series |
| Mass ranges available: 100 u, 200 u, 300 u p.11 ↗ | Select mass range per target gas species; calibration unit only calibrates reliably above 200 u with PFTBA | Ordering code position for mass range |
| Calibration medium is PFTBA, which persists in the background signal long after valve closure p.27 ↗ | Bake out the vacuum chamber after PFTBA calibration if low-level detection is required | Versions with calibration unit |
| Sealing gas (nitrogen) in the corrosive gas version: ~300 sccm flows to the exhaust connection and dilutes inlet gas concentrations by factor > 100 p.28 ↗ | Size exhaust/scrubber line for ~300 sccm sealing gas plus sample flow; no overpressure allowed at the exhaust connection | Corrosive gas versions (GSD 350 O C / T C) |
| Digital pressure switch triggers shutdown if sealing gas pressure exceeds or drops below the permissible range p.28 ↗ | Integrate the pressure switch signal into the process safety chain for corrosive-gas operation | Corrosive gas versions |
| Ambient limits: 10–40 °C, max 2000 m altitude, IP30, rel. humidity max 80% (<31 °C) / 50% (<40 °C), pollution degree 2 p.19 ↗ | Installation site must be weatherproof indoor space within these limits; outdoor or ATEX use invalidates warranty | Whole series |
| Unit weight up to 26 kg; two-person lift required p.16 ↗ | Plan installation and handling with 2 persons or lifting aids | Whole series |
| OmniStar gas inlet is controlled by two valves (gas inlet valve V1 and pump valve V2) allowing background/zero-gas measurement; ThermoStar inlet is continuously open p.26 ↗ | Choose OmniStar when individual gas admission and background subtraction are needed; ThermoStar for reactive/low-concentration gases | OmniStar vs ThermoStar |
| Zero gas must be supplied at the same pressure conditions as the analyzed gas for accurate background determination p.26 ↗ | Provide a zero-gas source at process pressure for high-precision measurements | Whole series |
| Mains connection via IEC 320 C13; 3-pin cable with protective earth; cables must satisfy double isolation per IEC 61010/IEC 60950; connect mains cable first p.16 ↗ | Specify compliant cabling and earthing during installation; protective earth continuity is mandatory before other connections | Whole series |
| Hot surfaces > 50 °C (heating components, gas inlet) and capillary tube surfaces possibly > 70 °C depending on setting p.16 ↗ | Provide touch protection, warning signs and EN 420 gloves; route cables away from > 70 °C surfaces | Whole series |
| Quartz capillary ends 1–2 mm in front of the orifice; quartz capillaries splinter — safety goggles required during trimming p.26 ↗ | Do not insert quartz capillary deeper; wear eye protection during capillary servicing | ThermoStar |
| Vacuum system components: HiPace 80 turbopump (SplitFlow, TC 110 drive), MVP 010-3 DC diaphragm pump, EVI 005 M mini angle valve on calibration unit, DigiLine MPT 200 AR total pressure gauge p.10 ↗ | Refer to the respective component manuals for service limits and spare parts; fore-vacuum connection is G 1/4" | Whole series |
| Network control via Ethernet RJ-45 with DHCP/static IP configuration; display-less variants are controlled exclusively via web interface; PoE used for display p.40 ↗ | Plan IP addressing/sub-network for integration; non-display units require web interface access for all operation | Whole series |
| Special tool PV M40 813 required for turbopump housing cover p.102 ↗ | Procure this tool before attempting level-2/3 service on the turbopump | Whole series |
| Maintenance levels: 1 (trained customer), 2 (technically educated customer or PV service), 3 (PV-service-trained customer or PV service) p.20 ↗ | Assign internal staff to appropriate maintenance level and schedule PV training for deeper interventions | Whole series |