Induztr
Engineering Digest Document Viewer Related Models

Calibration system Pro — product leaflet

Technical Reference Summary

Covered Models & Document Scope

Pfeiffer Vacuum 'Calibration system Pro', a standardized vacuum gauge calibration system compliant with ISO/TS 3567. Covers the base system plus options/accessories: reference gauges (CMR or CCT type), OmniControl, TPG 366 indicator/controller for 6 gauges, various connection flanges, custom flange/pump configurations and a larger recipient on request. DakkS-certified reference gauges available.

Section-by-Section Technical Breakdown

pp. 1
System Overview

The Calibration system Pro is a standardized, proven calibration system for vacuum gauges compliant with ISO/TS 3567 requirements. It can be operated manually by hand or via an integrated control unit. Individual flange connections can be configured to customer requirements.

  • Compliant with ISO/TS 3567
  • Manual and integrated control unit operation
  • Individual flange connections to fit customer requirements
  • DakkS-certified reference gauges available (CMR or CCT type)
  • Accessories: wide range of spare parts, OmniControl, TPG 366 indicator and controller for 6 gauges, larger recipient on request
pp. 2
Technical Data

This section lists the complete technical specifications of the Calibration system Pro, including pressure performance, pumping speeds, electrical data, flange connections, and physical characteristics. Precision depends on the reference gauges used.

  • Ultimate pressure: < 1 · 10⁻⁷ hPa (mbar)
  • Measurement range: 1 · 10⁻⁴ – 1 · 10³ hPa (mbar)
  • Pumping speed backing pump: 2.5 / 2.9 m³/h (50/60 Hz)
  • Pumping speed for N₂: 67 l/s
  • Input voltage: 115/230 V AC (50/60 Hz)
  • Power consumption: 230 VA
  • Actuator / mode of operation: manual
  • Cable length: 3 m
  • Material: stainless steel, glass bead blasted
  • Weight approx.: 66 kg
  • Connecting flange (in): DN 16 ISO-KF
  • Gas inlet: DN 16 ISO-KF
  • Gas flow range: 5 · 10⁻⁶ – 1 · 10³ hPa · l/s
pp. 2
Connections and Configurations

The system provides multiple gauge connection flange configurations and dimensional drawing data. Various connection flange sets and individual flange/pump configurations are available on request.

  • Connection configurations for gauges: 1x DN 40 ISO-KF, 4x DN 16 ISO-KF, 2x DN 25 ISO-KF; or 1x DN 40 CF, 5x DN 16 ISO-KF, 2x DN 25 ISO-KF, 2x DN 40 ISO-KF
  • Dimensional drawing provided in datasheet
  • Individual flange and/or pump configurations on request

Key Integration, Operating & Safety Requirements

Specification / Condition Engineering Implication Applies To
Ultimate pressure of the system is < 1 · 10⁻⁷ hPa (mbar) p.2 ↗ Sufficient vacuum quality for calibrating gauges down to high-vacuum range lower limits whole series
Measurement range is 1 · 10⁻⁴ to 1 · 10³ hPa (mbar) p.2 ↗ Defines the pressure span over which reference gauge comparisons can be performed whole series
Gas flow range is 5 · 10⁻⁶ to 1 · 10³ hPa · l/s p.2 ↗ Sets limits for leak/throughput calibrations achievable on the system whole series
Pumping speed for N₂ is 67 l/s p.2 ↗ High-vacuum pumping capacity for fast pressure reduction and stable calibration conditions whole series
Backing pump pumping speed is 2.5 m³/h at 50 Hz and 2.9 m³/h at 60 Hz p.2 ↗ Backing pump sizing/selection when configuring pump replacements whole series
Input voltage is 115/230 V AC at 50/60 Hz p.2 ↗ Suitable for both US and EU power grids without conversion whole series
Power consumption is 230 VA p.2 ↗ Circuit/breaker sizing and energy planning for installation whole series
System weight is approximately 66 kg p.2 ↗ Bench/table load capacity and lifting equipment must be specified accordingly whole series
Construction material is stainless steel, glass bead blasted p.2 ↗ Corrosion-resistant, clean-suitable surfaces for vacuum applications; affects surface finish expectations whole series
Actuator and mode of operation are manual, with 3 m cable length p.2 ↗ No automation required for basic operation; 3 m cable constrains control unit placement whole series
Gas inlet and connecting flange (in) are DN 16 ISO-KF p.2 ↗ Fixes the interface for gas admission and primary inlet hardware whole series
Two gauge-connection configurations offered: 1x DN 40 ISO-KF + 4x DN 16 ISO-KF + 2x DN 25 ISO-KF, or 1x DN 40 CF + 5x DN 16 ISO-KF + 2x DN 25 ISO-KF + 2x DN 40 ISO-KF p.2 ↗ Choice of configuration determines how many and which types of gauges can be mounted simultaneously for comparison calibration whole series
Precision depends on the used reference gauges (CMR or CCT types, DakkS-certified available) p.1 ↗ Overall calibration accuracy must be derived from the selected reference gauge's certificate, not from the system datasheet whole series, variant-dependent
Compliance with requirements of ISO/TS 3567 p.1 ↗ System is suitable for standardized vacuum gauge calibrations per this norm; audits can reference it directly whole series
Optional TPG 366 indicator/controller supports 6 gauges p.1 ↗ Enables simultaneous readout/control for multi-gauge comparison setups option for whole series
Larger recipient and individual flange/pump configurations available on request p.1 ↗ Custom test volume or pump setups can be ordered rather than requiring third-party modification whole series, factory option