Induztr
Resumen técnico Visor de documentos Modelos relacionados

Agilent 2200 TapeStation System Troubleshooting Manual

Technical Reference Summary

Covered Models & Document Scope

Abarca la familia de sistemas Agilent 2200 TapeStation: 2200 TapeStation (G2964AA), 2200 Nucleic Acid TapeStation (G2965AA), 2200 ScreenPlex TapeStation (G2966AA) y las variantes heredadas Lab901 TapeStation (ST007, ST008, ST009, ST010, ST017, ST019). Incluye resolución de problemas de aplicaciones de ADN, ARN y proteínas, compatibilidad de ScreenTape, comunicación USB, mantenimiento y mensajes de error.

Section-by-Section Technical Breakdown

pp. 5-20
Prácticas esenciales de medición

Cubre el uso previsto, las limitaciones de rendimiento, las herramientas y la manipulación, las recomendaciones de mezcla, la manipulación de reactivos y muestras, la manipulación de ScreenTape, los límites de LED y temperatura del instrumento, los consumibles y la asignación manual de marcadores. Estas prácticas son requisitos previos para una separación electroforética fiable de ácidos nucleicos y proteínas.

  • Maximum 16 samples per ScreenTape device; more samples require a 96-well plate and multiple ScreenTape.
  • Use reverse pipetting for RNA and High Sensitivity RNA assays.
  • Vortex mix with IKA MS3 default setting (1 minute) or manually 10 seconds at maximum speed.
  • Equilibrate reagents and samples to room temperature for 30 minutes before use.
  • Store ScreenTape at 2 – 8 °C; partially used ScreenTape max 2 weeks stored vertically.
  • Blue LED: idle steady, slow flash during run, fast flash indicates an issue.
  • Minimum 3 µL sample volume must be at the bottom of the tube without air bubbles.
pp. 21-22
Software 2200 TapeStation y compatibilidad de ScreenTape

Proporciona la versión mínima de software TapeStation requerida para cada ensayo ScreenTape y variante de instrumento. El software se descarga del sitio web de Agilent Genomics; el instrumento no debe estar conectado al portátil durante la instalación o actualización.

  • P200 ScreenTape (5067-5371) requires A.01.01 on G2964AA and Lab901-ST010; not compatible with G2965AA, G2966AA and other legacy systems.
  • Genomic DNA ScreenTape (5067-5365) requires A.01.03 on G2964AA, G2965AA, G2966AA, Lab901-ST010, ST017, ST019.
  • D1000, HS D1000, RNA and HS RNA ScreenTape (5067-5582, 5067-5584, 5067-5576, 5067-5579) require A.01.04 on all compatible systems.
  • Legacy Lab901-ST007, ST008 and ST009 are not compatible with any listed ScreenTape.
pp. 23-34
Comunicación del instrumento y configuración USB

Describe el orden de encendido, la conexión USB, el procedimiento de actualización del controlador USB, los requisitos del lector de códigos de barras y la recuperación de archivos de registro. Cada instrumento expone tres dispositivos USB: lector de códigos de barras, convertidor USB a serie y cámara.

  • Power up in order: laptop, instrument, controller.
  • Power down laptops and instruments at night; save run files to a local folder on the TapeStation laptop.
  • Barcode reader identified as 5180 Area Imager; USB-to-serial converter as USB↔Serial Converter.
  • Camera: uEye UI-154x Series for G2965AA; uEye UI-224x Series for G2964AA.
  • Place instrument away from direct light sources to avoid barcode recognition failure.
  • Insert ScreenTape with label towards the front and barcode facing right.
  • Export error logs via Help > Export Error Logs in the TapeStation Analysis Software.
pp. 35-37
Resolución de problemas del instrumento — Carriles en blanco

Explica las causas de carriles en blanco en el archivo de análisis, ordenadas por probabilidad, y sus acciones correctivas. Los carriles en blanco aparecen como carriles blancos sin picos visibles o como carriles negros granulosos con una señal de muestra muy baja.

  • Ensure all 16 tips are loaded into the tip rack at the start of each run.
  • Centrifuge sample strips or 96-well plates after preparation to remove bubbles at the bottom of wells.
  • Ensure a minimum of 3 µL of solution in the sample tubes; do not re-use sample strips.
  • Ensure positions selected in the controller software match the sample strip locations.
  • Remove sample strip lids before starting the run to avoid instrument damage.
  • If all causes are ruled out, a hardware fault may exist; contact local support.
pp. 39-58
Resolución de problemas de aplicaciones de ADN

Cubre buenas prácticas de medición para cuantificación, tamaño y molaridad de ADN, incluidos efectos de mezcla, integración de picos, identificación de marcadores, aspectos específicos del ensayo de ADN genómico y tablas de resolución de problemas para cuantificación incorrecta, tamaño incorrecto y picos de marcador ausentes.

  • Insufficient mixing dramatically lowers reported concentration: 68.5 ng/µL with vortex mixing vs 21.2 ng/µL with pipette mixing only vs 6.5 ng/µL with no mixing (theoretical 70 ng/µL).
  • In DNA assays concentration is calculated from sample peak area relative to the known upper marker concentration; RNA, HS RNA and Genomic DNA use the lower marker.
  • Electropherogram view reports the highest point of the peak; Region view reports the center of the region's mass.
  • Genomic DNA reagents must equilibrate to room temperature for 30 minutes; cold reagents overestimate size (+43 % at 4 °C vs +11 % at RT).
  • Prepare Genomic DNA ladder fresh for each run and run it in the first available position.
  • Do not shake the Genomic DNA ladder vial; inversion 30 times degrades the top 48,500 bp fragment and can prevent DIN scoring.
  • For SureSelect, increase magnetic plate incubation to 10 minutes to remove residual AMPure XP beads that run with the upper marker.
pp. 67-74
Resolución de problemas de aplicaciones de ARN

Cubre la resolución de problemas de ensayos de ARN, incluidos cuantificación incorrecta, tamaño incorrecto, picos de marcador ausentes, escalera de ARN y/o muestras degradadas, valor RINe incorrecto o ausente, anotación de picos incorrecta o ausente y perfil de migración inesperado.

  • RNA and High Sensitivity RNA assays require reverse pipetting.
  • RNA ScreenTape and HS RNA ScreenTape require software A.01.04.
  • RNA assays contain only a lower marker.
pp. 79-84
Resolución de problemas de aplicaciones de proteínas

Cubre la compatibilidad de tampones, la cuantificación de muestras de proteínas, los resultados de cuantificación y tamaño incorrectos y los perfiles de migración inesperados para ensayos de proteínas en el 2200 TapeStation.

  • Protein assays require a heating block or PCR machine (not supplied).
  • P200 ScreenTape is used for protein applications and requires software A.01.01 on G2964AA.
pp. 85-91
Mantenimiento del instrumento

Proporciona información general de mantenimiento, el procedimiento para cambiar la aguja y el intervalo de mantenimiento preventivo.

  • Needle replacement procedure is described in this section.
  • Preventative maintenance interval is specified in this section.
pp. 93-103
Mensajes de error

Enumera los mensajes de advertencia del software de análisis, los mensajes de error de comunicación y los mensajes de error de consumibles con sus significados y acciones correctivas.

  • Communication error: 'Failed to connect to the barcode scanner or camera' indicates a USB connection or driver issue.
  • Temperature out of range error appears when the instrument is outside the recommended range for the inserted ScreenTape.
  • Consumable error messages relate to ScreenTape and tip handling.
pp. 105-109
Productos ScreenTape, piezas y consumibles

Enumera los productos ScreenTape y las piezas y consumibles requeridos para el sistema 2200 TapeStation, incluidas puntas de carga, tiras de muestra, placas, sellos de aluminio y la caja de envío.

  • Loading tips: 5067-5152 or 5067-5153.
  • Optical Tube 8x Strip 401428 and Optical Cap 8x Strip 401425, or 96-well Sample Plates 5067-5150 and 96-well Plate Foil Seal 5067-5154.
  • Shipping box part number G2960-60100.
  • IKA MS3 vortexer part number 4674100 (obtainable from IKA quoting 'Agilent Technologies').

Key Integration, Operating & Safety Requirements

Specification / Condition Engineering Implication Aplica a
El 2200 TapeStation puede analizar un máximo de 16 muestras en un único dispositivo ScreenTape. p.8 ↗ Higher throughput requires a 96-well plate and multiple ScreenTape devices. whole series
El instrumento cargará una muestra a partir de un mínimo de 3 µL en ScreenTape. p.12 ↗ Sample tubes must contain at least 3 µL at the bottom without air bubbles to avoid blank lanes. whole series
La temperatura óptima de funcionamiento del instrumento es 20 °C; los rangos específicos del ensayo son 12–37 °C (D1000), 17–37 °C (HS D1000), 15–30 °C (ADN genómico), 14–30 °C (ARN/HS ARN) y 10–33 °C (P200). p.15 ↗ Operating outside the assay-specific range triggers a 'Temperature out of Range' error and invalidates the run. whole series
ScreenTape debe almacenarse a 2 – 8 °C y puede usarse directamente del refrigerador sin tiempo de equilibrado. p.13 ↗ No warm-up time is needed, but partially used ScreenTape must be returned to 2 – 8 °C vertically and used within 2 weeks. whole series
El ScreenTape parcialmente usado debe usarse con el mismo portátil que realizó las ejecuciones anteriores porque los datos de ejecución se almacenan localmente en el portátil del instrumento. p.14 ↗ Changing or updating the laptop can cause lane usage information to be lost and partially used lanes to be reused. whole series
La mezcla con vórtex con el IKA MS3 a 2.000 rpm durante 1 minuto seguida de una breve centrifugación produce 68,5 ng/µL frente a 21,2 ng/µL para solo mezcla con pipeta y 6,5 ng/µL para sin mezcla (teórico 70 ng/µL). p.41 ↗ Insufficient mixing dramatically underestimates concentration; the recommended vortex protocol is mandatory for accurate quantification. D1000 ScreenTape assay
Los reactivos de ADN genómico equilibrados a 4 °C sobreestiman el tamaño en +43 % (24369 pb frente a 17000 pb esperados), mientras que los reactivos equilibrados a temperatura ambiente dan +11 % (18867 pb). p.50 ↗ Genomic DNA reagents must be equilibrated to room temperature for 30 minutes before use. Genomic DNA ScreenTape assay
Agitar el vial de escalera de ADN genómico invirtiéndolo 30 veces degrada el fragmento superior de 48.500 pb y puede impedir que se presenten las puntuaciones DIN. p.51 ↗ Handle the ladder vial carefully before adding sample buffer; after mixing with sample buffer vortex gently for 5 seconds. Genomic DNA ScreenTape assay
Los reactivos de ADN genómico se envían congelados en hielo seco y deben mantenerse a 2 – 8 °C en el refrigerador al recibirlos. p.51 ↗ Storage at 2 – 8 °C preserves reagent integrity and sizing accuracy. Genomic DNA ScreenTape assay
En el flujo de trabajo SureSelect, las perlas AMPure XP residuales migran con el marcador superior y disminuyen la concentración de muestra reportada; aumentar la incubación de la placa magnética a 10 minutos elimina un mayor porcentaje de perlas. p.46 ↗ Extend magnetic plate incubation to 10 minutes when using SureSelect to avoid concentration bias. SureSelect workflow on 2200 TapeStation
En los ensayos de ADN la concentración se calcula a partir del área del pico de la muestra en relación con la concentración conocida del marcador superior; los ensayos de ARN, HS ARN y ADN genómico utilizan el marcador inferior. p.43 ↗ Peak integration must be manually adjusted when necessary to encompass the whole peak, otherwise concentration is biased. whole series
La vista de electroferograma informa el punto más alto del pico, mientras que la vista de región informa el centro de la masa de la región. p.47 ↗ Select the analysis mode appropriate to the sample type (discrete peaks vs smears/NGS libraries) to obtain the intended sizing value. whole series
El orden de encendido debe ser portátil, luego instrumento, luego controlador; los portátiles e instrumentos deben apagarse por la noche. p.24 ↗ Following the power sequence avoids communication failures between laptop and instrument. whole series
Cada instrumento expone tres dispositivos USB: 5180 Area Imager (lector de códigos de barras), USB↔Serial Converter y cámara uEye UI-154x (G2965AA) o uEye UI-224x (G2964AA). p.27 ↗ A missing or exclamation-marked device in Device Manager indicates a driver update is required. G2964AA, G2965AA
El instrumento debe colocarse lejos de fuentes de luz directa porque el exceso de luz interfiere con el reconocimiento de códigos de barras. p.33 ↗ Direct sunlight or strong lighting can cause a non-functioning instrument due to barcode read failure. whole series
Antes del transporte, habilite el 'modo de transporte' en el software del controlador mediante el menú desplegable Transport y retire la placa de muestras, el soporte de puntas y el ScreenTape. p.16 ↗ Failure to enable transport mode or remove components before transport can damage the instrument. whole series
Las cajas de envío para transporte se pueden adquirir con el número de pieza G2960-60100. p.16 ↗ Use the correct packaging when transporting the instrument. whole series
El vórtex IKA MS3 (número de pieza 4674100) se incluye con los instrumentos 2200 TapeStation (G2965AA o G2964AA) e incluye un adaptador para placas de 96 pocillos para placas de PCR de 96 pocillos y tiras de 8. p.10 ↗ Use the IKA MS3 with adaptor for the recommended vortex mixing protocol; it is not sold separately by Agilent. G2964AA, G2965AA
Las puntas de carga son 5067-5152 o 5067-5153; las tiras de muestra son Optical Tube 8x Strip 401428 con Optical Cap 8x Strip 401425, o placas de muestra de 96 pocillos 5067-5150 con sello de aluminio para placa de 96 pocillos 5067-5154. p.17 ↗ Only Agilent 2200 TapeStation approved consumables must be used to avoid instrument damage and performance impact. whole series
La escalera de ADN genómico debe prepararse fresca para cada ejecución y ejecutarse en la primera posición disponible porque el perfil de ejecución disminuye a medida que la escalera se calienta dentro del instrumento. p.50 ↗ Reusing or repositioning the ladder affects sizing results. Genomic DNA ScreenTape assay

Faults & Troubleshooting

Código / Síntoma Possible Cause Remedy Note
Temperature out of Range p.15 ↗ Instrument temperature outside the recommended range for the inserted ScreenTape. If above range, move the system out of direct sunlight and away from windows and check air conditioning. If below range, allow the instrument to equilibrate to ambient temperature and avoid using in a cooled area. Figure 3
Failed to connect to the barcode scanner or camera p.26 ↗ Laptop fails to connect to the instrument or loses connection; USB cable or driver issue. Check that power and USB cables are attached to the instrument; if issues remain, re-install the USB drivers. Updating USB Drivers
Blank lane (white lane with no visible peaks) p.37 ↗ Tips in the selected positions were missing from the tip rack. Always ensure that all 16 tips are loaded into the tip rack at the start of each run. Table 2
Blank lane (white lane with no visible peaks) p.37 ↗ A bubble in the sample tube prevented the sample from being picked up. Always ensure that sample strips or 96-well plates are centrifuged after preparation to remove any bubbles present at the bottom of wells. Table 2
Blank lane (white lane with no visible peaks) p.37 ↗ Insufficient sample present. Always ensure a minimum of 3 µL of solution is present in the sample tubes. Do not re-use sample strips from previous runs. Table 2
Blank lane (white lane with no visible peaks) p.37 ↗ The samples were not selected correctly in the controller software. Always ensure that the positions selected in the controller software match the location of the sample strips within the instrument. Table 2
Blank lane (white lane with no visible peaks) p.37 ↗ The sample lids were not correctly removed before starting the run. Always ensure that sample strip lids are removed before starting the run. Failure to do so can result in damage to the instrument. Table 2
Blank lane (black grainy lane with very small sample intensity values) p.37 ↗ Hardware fault. If the above causes have been ruled out, send all relevant data to your local support representative for investigation. Table 2
Incorrect quantification results p.53 ↗ Insufficient mixing. Ensure correct mixing by reading the mixing recommendations. Table 5
Incorrect quantification results p.53 ↗ Sample concentration outside recommended range for application. Either dilute or concentrate your sample until it is within the recommended range for application as stated in the assay Quick Guide, then prepare a new run. Table 5
Incorrect quantification results p.53 ↗ Incorrect peak integration. Ensure that all sample peaks and markers are integrated correctly in the TapeStation Analysis Software, by clicking and dragging so that the whole peak is encompassed. Table 5
Incorrect quantification results p.53 ↗ Some sample has run concurrently with the upper marker. Ensure your sample is within the recommended sizing range for the application. If using SureSelect Protocol, ensure that all AMPure beads are removed by increasing the time your sample is on the magnetic plate. Table 5
Incorrect quantification results p.53 ↗ Incorrect protocol used. Ensure the correct sample protocol for the application is used. Differences exist between standard and High Sensitivity assay protocols; consult the User Manual or appropriate Quick Guides. Table 5
Incorrect quantification results p.53 ↗ Sample prepared too long before analysis. To avoid evaporation or settling, ensure that your run is started immediately after your sample preparation. If using a 96-well plate, always cover with the recommended foil seal. Table 5
Incorrect quantification results p.53 ↗ Incorrect pipetting technique or pipette calibration. Follow guidelines in the essential measurement practices section. Table 5
Incorrect quantification results p.53 ↗ Incorrect marker peaks picked up. Use the Aligned button in the TapeStation Analysis Software to detect the correct markers, then assign them by right clicking. Ensure that all sample peaks are within the recommended sizing range for the application. Table 5
Incorrect sizing results p.55 ↗ Incorrect marker peaks picked up. Ensure the correct marker peaks are picked up in the TapeStation Analysis Software. Ensure that all sample peaks are within the recommended sizing range for the application. Table 6
Incorrect sizing results p.55 ↗ Incorrect analysis software mode. Reported sizing can differ between electropherogram and region modes. Select the correct mode for your samples. Table 6
Incorrect sizing results p.55 ↗ Issues with the ladder lane. Any issues with the run ladder lane will be annotated within the TapeStation Analysis Software sample table, under Observations. Manually insert or delete affected peaks, or insert a software saved ladder to regain sizing information (if available). Table 6
Incorrect sizing results p.55 ↗ Insufficient migration due to presence of salt. Dilute your samples to ensure low levels of buffer salt. True migration profiles can be seen by unaligning your gel image by pressing the Aligned button. Refer to the salt tolerance guidelines for your assay. Table 6
Missing marker peaks p.57 ↗ Insufficient mixing. Ensure correct mixing by reading the mixing recommendations. Table 7
Missing marker peaks p.57 ↗ Sample concentration outside recommended range for application. Either dilute or concentrate your sample until it is within the recommended range for application as stated in the assay Quick Guide, then prepare a new run. Table 7
Missing marker peaks p.57 ↗ Blank lane. See Blank lane section. Table 7
Missing marker peaks p.57 ↗ Insufficient migration. To check migration true distance, unalign the gel image using the Aligned button. Table 7

Technical Data

Parameter Value Condición
Maximum samples per ScreenTape device 16 samples p.8 ↗
Minimum sample volume loaded onto ScreenTape 3 µL p.12 ↗
Optimal instrument operating temperature 20 °C p.15 ↗
Assay operating temperature 12 – 37 °C p.15 ↗ D1000 ScreenTape
Assay operating temperature 17 – 37 °C p.15 ↗ High Sensitivity D1000 ScreenTape
Assay operating temperature 15 – 30 °C p.15 ↗ Genomic DNA ScreenTape
Assay operating temperature 14 – 30 °C p.15 ↗ RNA and High Sensitivity RNA ScreenTape
Assay operating temperature 10 – 33 °C p.15 ↗ P200 ScreenTape
ScreenTape storage temperature 2 – 8 °C p.13 ↗
Maximum storage time for partially used ScreenTape 2 weeks p.14 ↗ stored vertically at 2 – 8 °C
Reagent equilibration time to room temperature 30 minutes p.11 ↗
Sample equilibration time to room temperature 30 minutes p.12 ↗
Vortex mixing time with IKA MS3 default setting 1 minute p.10 ↗ D1000, HS D1000, RNA, HS RNA ScreenTape assays
Manual vortex mixing time at maximum speed 10 seconds p.10 ↗ if IKA MS3 not available
Vortex mixing speed for recommended protocol 2,000 rpm p.41 ↗ IKA vortexer with adaptor, 1 minute
Genomic DNA ladder vortex mixing time after addition of sample buffer 5 seconds p.51 ↗ gentle vortex
Magnetic plate incubation time for SureSelect AMPure bead removal 10 minutes p.46 ↗ SureSelect workflow
Genomic DNA sizing accuracy with reagents at RT +11 % p.50 ↗ expected 17000 bp, measured 18867 bp
Genomic DNA sizing accuracy with reagents at 4 °C +43 % p.50 ↗ expected 17000 bp, measured 24369 bp
Measured concentration with vortex mixing then centrifugation 68.5 ng/µL p.42 ↗ D1000 assay, theoretical 70 ng/µL
Measured concentration with pipette mixing only 21.2 ng/µL p.42 ↗ D1000 assay, theoretical 70 ng/µL
Measured concentration with no mixing 6.5 ng/µL p.42 ↗ D1000 assay, theoretical 70 ng/µL