Agilent 240 Ion Trap GC/MS Hybrid Ionization Users Guide
Technical Reference Summary
Covered Models & Document Scope
Cubre la configuración de ionización híbrida del sistema GC/MS de trampa de iones Agilent 240, incluidos los modos PCI híbrido y NCI híbrido, las opciones HPS (fuente de alta presión) y LPS (fuente de baja presión) híbridas, y la conversión de modo desde configuraciones interna o externa. Requiere la opción de ionización externa, la opción de ionización química y un chip de seguridad.
Section-by-Section Technical Breakdown
Describe la configuración híbrida del GC/MS de trampa de iones 240, donde los iones reactivos se generan en la fuente externa mediante EI de un gas reactivo y se introducen en la trampa de iones para reaccionar con los analitos. La CI híbrida es una técnica de ionización más suave que la EI, que produce menos fragmentación y más información sobre el peso molecular. El modo requiere la opción de ionización externa, la opción de ionización química y un chip de seguridad.
- Hybrid configuration is one of three operational configurations of the 240 Ion Trap GC/MS.
- Reagent ions are generated in the external source through EI of a reagent gas.
- Advantages include avoiding ion-molecule reactions with neutral reagent and avoiding negative ion losses.
- Hybrid CI imparts less energy than EI, reducing fragmentation.
- Requires external ionization option, chemical ionization option, and a security chip.
- Supports SIS, and with optional software/equipment MS/MS, MSn, AMD, and MRM.
Explica cómo utilizar la función Ver iones reactivos para ajustar el aislamiento de iones reactivos individuales. Cuando no se especifica una amplitud de eyección, se pueden ver todos los iones en el rango de masas de inicio y fin de iones reactivos.
- Use View Reagent Ions to tune isolation of individual reagent ions.
- Without Ejection Amplitude, all ions in the range are viewed.
- Schematic shows E.M. end cap, filament end cap, lens structure, CI volume assembly, filament, transfer line tip, ring electrode, electron multiplier, and H.E. dynode.
Explica el análisis de masas mediante el aumento gradual del voltaje de RF en el electrodo anular, la eyección de iones hacia el dínodo de conversión y el multiplicador de electrones, y el control AGC del tiempo de ionización. El dínodo de conversión se mantiene a -10,000 V en modos positivos y a +10,000 V en modo negativo; la señal se amplifica en ~10^5.
- Ions are ejected from low to high mass by increasing RF voltage on the ring electrode.
- Supplemental dipole and quadrupole voltages improve mass resolution.
- Conversion dynode held at -10,000 V in positive modes, +10,000 V in negative mode.
- Signal amplified by ~10^5 by the electron multiplier.
- AGC prescan and up to six analytical scan segments.
- Ion trap has a maximum storage capacity beyond which resolution and spectral quality deteriorate.
Señala que el software 240 MS no incluye bibliotecas de espectros de masas de PCI o NCI híbridos, pero los usuarios pueden crear bibliotecas. Analiza las ventajas de selectividad de la CI híbrida, incluida la baja respuesta de hidrocarburos en PCI con metano y la buena respuesta de NCI para especies con alta afinidad electrónica.
- No Hybrid PCI or NCI libraries included with 240 MS software.
- Users can create libraries of Hybrid spectra.
- Hydrocarbons have poor response in methane PCI.
- Negative CI gives good response only for species with high electron affinity such as halogenated compounds.
- Analyzing samples with multiple ionization and ion preparation options is recommended during method development.
Proporciona instrucciones para instalar gas CI de metano y ajustar el flujo de gas CI. Conecte el regulador a través de un restrictor de 50 mL/min, ajuste la segunda etapa a 20 psi y ajuste la válvula de gas CI hasta que la presión del medidor de iones esté dentro de 70 a 100 µTorr.
- Connect gas cylinder regulator to the back of the instrument through a 50 mL/min restrictor.
- Set methane regulator second stage to 20 psi.
- Use CI Gas Adjust Valve inside the front door of the 240 MS.
- Turn knob clockwise to increase flow, counterclockwise to decrease.
- Set ion gauge pressure within 70 to 100 µTorr.
- Liquid reagents like methanol and acetonitrile give weak responses in Hybrid PCI.
Describe el inicio de la adquisición, la verificación de la preparación del GC y del automuestreador, y la ejecución de muestras individuales o listas de muestras. El software cambia automáticamente el módulo MS al modo de adquisición. Los indicadores de estado incluyen tiempo de ejecución, hora de finalización y luces de listo/sin fallos.
- Click Start Acquisition to start a run.
- Software automatically shifts MS module into Acquisition mode.
- Not Ready message changes to Ready when GC and AutoSampler are ready.
- Individual ready states visible under Windows pull-down menu for 240 MS, 7890 GC, and sampler modules.
- Before acquisition, Run Time is 0.00 minutes and Ready/No Fault lights are green.
Instrucciones paso a paso para inyectar una muestra individual, incluido el ingreso del nombre de la muestra, el número de vial, el volumen de inyección y la información del archivo de datos. Para la inyección manual, espere a que la barra de título de Control del sistema muestre 'Waiting for Injection of Sample' y una luz amarilla parpadeante de espera.
- Click Inject Single Sample from the Inject menu.
- Enter sample name, vial number, injection volume, and injector.
- Click Defaults to change default values.
- Click Data Files to create a name with date/time or change storage directory.
- For manual injection, wait for 'Waiting for Injection of Sample' and blinking yellow Waiting light.
Explica cómo crear y editar una lista de muestras en el Editor de archivos de automatización o en Control del sistema, e inyectar varias muestras. La columna Nombre de muestra no se desplaza cuando la tabla se desplaza a la derecha.
- Create and edit Sample List in Automation File Editor or System Control.
- Click New Sample List or Open Sample List from File menu.
- Sample List window contains fields specific to the configured autosampler.
- Sample Name column remains visible when scrolling right.
- Click Begin in lower left corner to start the Sample List.
Describe el monitoreo del estado de ejecución en la ventana del instrumento y la visualización del cromatograma y los espectros en Control del sistema o Revisión de datos de MS.
- Monitor status of the run in the instrument window.
- Monitor chromatogram and spectra in System Control or MS Data Review.
- See Acquiring GC/MS Data section in the 240 Ion Trap GC/MS Software Operation help.
Enumera las verificaciones antes del bombeo inicial: conexiones de vacío sin fugas, línea de transferencia asentada en la trampa, válvula de venteo cerrada completamente en sentido horario, columna no rota. La bomba de respaldo debe dejar de hacer ruido de gorgoteo después de aproximadamente 10 a 20 segundos.
- Verify vacuum connections are leak free.
- Verify transfer line is seated in the trap.
- Verify vent valve is closed fully clockwise.
- Verify column is not broken.
- Roughing pump should stop gurgling after about 10 to 20 seconds.
- If pump continues to gurgle, check analyzer assembly seating, transfer line seating, and vent valve seal.
Proporciona rangos operativos típicos para el 240 MS en modo externo y explica el diagnóstico de fugas. Las fugas grandes se indican por una velocidad de la turbobomba inferior al 100%; las fugas pequeñas por un aumento de la corriente de la bomba o de la presión del medidor de iones.
- Typical turbo speed: 100%.
- Typical pump current: 200 to 300 mAmps.
- Typical power: 9 to 13 Watts.
- Typical ion gauge pressure: < 20 µTorr.
- Typical roughing line pressure: < 50 mTorr.
- Large leaks indicated by turbo speed less than 100%.
- Small leaks show as increased pump current or ion gauge pressure.
- Start without damping gas, then increase to 0.5 mL/min to test sensitivity.
Describe el monitoreo del estado del instrumento a través de la pestaña Monitoreo y la realización de verificaciones de hardware a través de la pestaña Diagnóstico. La elección inicial del flujo de gas de arrastre de helio es de 3 a 4 mL/min, configurado en la pestaña Atributos del módulo.
- Monitor vacuum system, electron multiplier, waveform system, temperatures, and ion source.
- Perform hardware checks on the 240 MS using the Diagnostics tab.
- Initial helium buffer gas flow choice is 3 to 4 mL/min.
- Set helium buffer gas flow rate in the Module Attributes tab.
Cubre las temperaturas de análisis, el acondicionamiento del sistema y los efectos de la temperatura en la calibración. La temperatura de la trampa de iones debe ser lo suficientemente alta para evitar la condensación. La temperatura de la línea de transferencia debe ser 20 °C inferior a la temperatura máxima de la columna. La temperatura predeterminada del colector suele ser de 50 °C.
- Ion trap temperature must prevent condensation of analyte eluting into the trap.
- Transfer line temperature should be 20 °C below maximum column temperature.
- Default manifold temperature is typically 50 °C.
- Perform mass calibration and trap function calibration shortly after source temperature is reached and again several hours later.
- Wait at least two hours after bakeout before AutoTune or running the 240 MS.
- Transfer line temperature should not exceed maximum isothermal temperature of the column.
Describe el uso de Inicio/Apagado para iniciar o apagar el sistema de forma segura. Durante el inicio, el software se bloquea hasta que la velocidad de la turbobomba alcanza el 100%. El apagado reduce la velocidad de la turbobomba al 35% de la velocidad máxima; después de que todas las zonas estén por debajo de 80 °C, apague la alimentación principal y ventile durante al menos 5 minutos.
- Software locked in Startup/Shutdown mode until turbo speed reaches 100%.
- Failure to reach 100% pump speed in reasonable time indicates a vacuum leak.
- Shutdown reduces turbo pump speed to 35% of full speed.
- After all temperature zones are below 80 °C, turn off main power at rear switch.
- Manually vent the system for at least 5 minutes using the front panel valve.
Cubre la ejecución de pruebas de diagnóstico, sintonización de RF, ajuste de rampa de RF, ajuste de gas CI, verificación de aire/agua, sintonización automática, cero del integrador, configuración del multiplicador de electrones, sintonización de lente de electrones, sintonización de lente de iones, ajuste de escala completa de RF, calibración de masas, calibración de frecuencia de trampa y voltaje de compensación de CC de trampa.
- Retract transfer line before lifting analyzer assembly to avoid damage.
- Run all routines in Diagnostic Tests tab after turbo reaches 100% speed.
- Adjust RF tuning after MS maintenance, changing analyzer assembly, or changing MS configuration.
- RF ramp adjustment: turn RF Adjustment screw until tuning display shows straight line and intensity at minimum.
- Air/Water Check uses electron multiplier voltage with gain at 10^5.
- Auto Tune works the same in EI or Hybrid CI modes.
- Electron lens balance range is 200 to 300 µA.
- For CI methods in Hybrid mode, electron/repeller lens must be tuned with CI plunger in place and CI gas on.
- Ion lens tuning uses Cal Gas ions at m/z 131 and 414.
- Mass calibration uses PFTBA ions at m/z 69, 131, 264, 414, 464, and 614.
- Do not run mass calibration until ion trap temperature has stabilized for at least two hours.
- Trap frequency calibration determines parameters for MS/MS and SIS.
- Trap DC offset optimizes ion signal for m/z 414.
Describe las funciones de barrido de CI híbrida donde los iones reactivos se crean durante el pulso de ionización y se consumen durante el período de reacción. Los resultados del prescan de AGC se utilizan para calcular el tiempo de ionización y el tiempo de reacción para el barrido analítico, lo que permite curvas de calibración lineales.
- Ion trap operates in pulsed mode.
- Reagent ions created only during ionization pulse and consumed during reaction period.
- Number of analyte ions depends on analyte concentration, initial reagent ion intensity, and reaction time.
- AGC prescan calculates ionization time and reaction time for analytical scan.
- Spectral intensity proportional to sample concentration and reaction time.
Instrucciones paso a paso para crear un nuevo método utilizando el asistente Constructor de métodos, incluida la selección del instrumento, detectores, canales de datos y procesamiento posterior a la ejecución. El método contiene secciones para Control del GC 7890, Control del MS 240, Informes estándar de MS y Manejo de datos de MS.
- Click Method Builder icon on Workstation Toolbar.
- Click Create a New Method File.
- Select Instrument 1 and click Next.
- Use Custom configuration to create methods on a PC remote from the instrument.
- Select detectors and data channels for post-run processing.
- Method contains default values for all parameters.
- In Hybrid Mode, instrument configuration is Chemical Ionization (CI).
Explica que los métodos híbridos solo se pueden realizar en modos PCI o NCI, excepto cuando se ejecutan métodos de sintonización automática que requieren el modo EI. La HPS (fuente de alta presión) híbrida se realiza con el volumen de CI insertado; la LPS (fuente de baja presión) ocurre en la fuente de EI. Los datos de centroide son predeterminados; los datos de perfil son para diagnóstico y aproximadamente 10 veces más grandes.
- Hybrid methods only in PCI or NCI modes, except Auto Tune methods requiring EI.
- Hybrid HPS performed with CI volume inserted into ion source.
- Hybrid LPS occurs in the EI source.
- Centroid data is default acquisition data type.
- Data handling, library searching, and spectral comparison only with centroid data.
- Profile data collected at 10 points per m/z and approximately 10 times larger than centroid files.
- Up to 250 time segments for runs up to 650 minutes.
Describe la edición de parámetros para métodos de CI híbrida, incluida la configuración de funciones de barrido, parámetros generales, control de ionización, parámetros híbridos y parámetros de barrido. Hay tres modos de barrido disponibles: Normal (5000 u/s), Rápido (10000 u/s) y Más rápido (10000 u/s, sin prescan, solo barrido completo).
- CI is the only ionization choice in Hybrid configuration.
- Normal scan mode uses prescan and scans at 5000 u/sec.
- Fast scan mode uses prescan and scans at 10000 u/sec.
- Fastest scan mode uses no prescan and scans at 10000 u/sec; only available in Full scan type.
- Scan Time, Scans Averaged, and Data Rate are linked.
- Setting scans averaged to three gives best compromise between data rate and spectral averaging.
- Mass Defect allows systematic correction of nominal vs exact mass.
- Multiplier Offset adjusts EM voltage by up to 300 V relative to current setting.
- Count Threshold normally 1; value of 2 or 3 reduces low-level ions reported.
- Target TIC usually not below 10,000 for full scan; typically 20,000 to 40,000 gives best results.
- Default Target TIC for CI is 5,000; maximum 65,000.
- Reagent Low Mass must be set at least 10u below lowest reagent ion of interest.
- Default Ejection Amplitude is 15 V.
- Max Reaction Time range is 1 to 2000 µsec.
- Reaction Storage Level should not be set above m/z of CI reagent ion.
- CI Background Mass is lowest m/z counted during CI prescan.
Cubre la configuración de parámetros de barrido completo y MS/MS. El barrido completo permite hasta seis rangos de masas no contiguos separados por al menos 10u. Los parámetros de MS/MS incluyen ion precursor, ventana de aislamiento (1.0 a 14.0 m/z, predeterminado 3.0), desplazamiento de borde bajo/alto (-0.5 a 0.5 m/z), eyección de masa alta (predeterminado 35 V) y tipo de forma de onda (resonante o no resonante).
- Up to six non-contiguous mass ranges separated by at least 10u for full scan.
- MS/MS isolation window range 1.0 to 14.0 m/z; default 3.0 m/z.
- If isolation window smaller than 1.5 m/z, enter exact precursor ion mass.
- Low Edge Offset range -0.5 to 0.5 m/z; default 0.
- High Edge Offset range -0.5 to 0.5 m/z; default 0.
- Adjust edge offsets initially in 0.2 m/z increments.
- High Mass Ejection default 35 volts.
- Waveform type is either resonant or non-resonant.
- MS/MS useful only when target compounds are known.
Cubre la conversión de configuraciones interna a híbrida y externa a híbrida, y los efectos de los cambios de hardware.
- Internal to Hybrid conversion.
- External to Hybrid conversion.
- Effects of hardware changes.
Key Integration, Operating & Safety Requirements
| Specification / Condition | Engineering Implication | Aplica a |
|---|---|---|
| El modo híbrido requiere la opción de ionización externa, la opción de ionización química y un chip de seguridad, pero no implica ningún hardware único. p.5 ↗ | Verify option licenses and security chip are installed before attempting Hybrid operation. | Hybrid configuration |
| El nivel de almacenamiento de RF predeterminado es 35u, por lo que los iones reactivos de CI a m/z 17 y 29 no se almacenan; solo los iones reactivos por encima de 35u reaccionan con las moléculas de analito. p.8 ↗ | This inherent selectivity can be used to avoid unwanted low-mass reagent ions; adjust Reagent Low Mass to change the storage cutoff. | Hybrid mode |
| Se utiliza un flujo de gas de arrastre de helio de 1 mL/min para el almacenamiento de iones; la elección inicial para poner en marcha el instrumento es de 3 a 4 mL/min. p.9 ↗ | Set helium flow in Module Attributes tab; trapping efficiency is compound dependent. | Whole series |
| El gas CI de metano se conecta a través de un restrictor de 50 mL/min y la segunda etapa del regulador se ajusta a 20 psi. p.13 ↗ | Use the specified restrictor and pressure to achieve correct CI gas flow. | Methane CI installation |
| El objetivo de ajuste del gas CI es una presión del medidor de iones dentro de 70 a 100 µTorr. p.13 ↗ | Adjust CI Gas Adjust Valve until adjustment result is OK before acquiring data in Hybrid CI mode. | Hybrid CI |
| El dínodo de conversión se mantiene a -10,000 V en modos positivos y a +10,000 V en modo negativo; la señal se amplifica en ~10^5 por el multiplicador de electrones. p.11 ↗ | Understand polarity-dependent dynode voltage for method setup and troubleshooting. | Whole series |
| Rangos operativos típicos en modo externo: velocidad de la turbobomba 100%, corriente de la bomba 200 a 300 mAmps, potencia 9 a 13 Watts, presión del medidor de iones < 20 µTorr, línea de respaldo < 50 mTorr. p.20 ↗ | Use these ranges to diagnose vacuum system health; deviations indicate leaks or pump issues. | 240 MS in External mode |
| La temperatura de la línea de transferencia debe ser 20 °C inferior a la temperatura máxima de la columna del método activo y no debe exceder la temperatura isotérmica máxima de la columna. p.22 ↗ | Set transfer line temperature to avoid cold spots while protecting the column. | Whole series |
| Después del acondicionamiento, espere al menos dos horas antes de intentar AutoTune o ejecutar el 240 MS. p.22 ↗ | Allow all temperature zones to equilibrate thoroughly to avoid calibration drift. | Whole series |
| Durante el apagado, la velocidad de la turbobomba se reduce al 35% de la velocidad máxima; después de que todas las zonas de temperatura estén por debajo de 80 °C, apague la alimentación principal y ventile durante al menos 5 minutos. p.24 ↗ | Follow this sequence to safely shut down and vent the system. | Whole series |
| El rango de balance de la lente de electrones es de 200 a 300 µA; si está fuera de este rango, la sintonización automática busca valores óptimos cambiando cuatro variables una a la vez. p.28 ↗ | If auto tune fails to find best lens voltage, it generates an error and restores last values. | Whole series |
| Para métodos de CI en modo híbrido, la lente de electrones/repelente debe sintonizarse con el émbolo de CI (volumen de CI) colocado y el gas CI encendido. p.28 ↗ | Adjust CI gas flow in Manual Control before performing electron lens tuning. | Hybrid CI |
| La calibración de masas utiliza iones de PFTBA a m/z 69, 131, 264, 414, 464 y 614; no ejecutar hasta que la temperatura de la trampa de iones se haya estabilizado durante al menos dos horas. p.29 ↗ | Temperature changes can shift the mass calibration axis; stabilize before calibration. | Whole series |
| El modo de barrido Normal escanea a 5000 u/s; los modos Rápido y Más rápido escanean a 10000 u/s; Más rápido no utiliza prescan y solo está disponible en el tipo de barrido completo. p.37 ↗ | Choose scan mode based on required data rate and spectral quality. | Whole series |
| El TIC objetivo predeterminado para CI es de 5,000 cuentas; los mejores resultados típicos se obtienen con 20,000 a 40,000 cuentas; máximo 65,000 cuentas. p.39 ↗ | Setting Target TIC too high can cause space charge distortions (loss of resolution or mass shift). | Hybrid CI |
| La masa baja de reactivo debe establecerse al menos 10u por debajo de la masa del ion reactivo de interés más bajo sin pérdida de intensidad. p.40 ↗ | This sets the RF storage level to exclude ions below the selected m/z. | Hybrid parameters |
| La amplitud de eyección predeterminada para el aislamiento de masa alta de iones reactivos de CI es de 15 V; el rango de tiempo de reacción máximo es de 1 a 2000 µsec. p.40 ↗ | Adjust these parameters to optimize reagent ion isolation and reaction time. | Hybrid parameters |
| El rango de ventana de aislamiento de MS/MS es de 1.0 a 14.0 m/z con un valor predeterminado de 3.0 m/z; si es menor que 1.5 m/z, ingrese la masa exacta del ion precursor. p.42 ↗ | Adjust isolation window and edge offsets to isolate precursor ions effectively. | MS/MS |
| La amplitud predeterminada de eyección de masa alta es de 35 voltios; reducirla puede ayudar si se pierden iones precursores debido a la disociación. p.43 ↗ | Balance ejection amplitude to retain precursor ions while removing higher-mass ions. | MS/MS |
| Se pueden crear hasta 250 segmentos de tiempo cromatográfico para ejecuciones de hasta 650 minutos de duración. p.36 ↗ | Time program analysis conditions to optimize data for each segment. | Whole series |
Faults & Troubleshooting
| Código / Síntoma | Possible Cause | Remedy | Note |
|---|---|---|---|
| Pump Spin Speed does not increase steadily p.20 ↗ | There may be a leak in the system. | Diagnose leaks by observing changes in ion gauge reading and pinpoint using leak check section in method Service.mth. See Troubleshooting section in 240 GC/MS Ion Trap Hardware Operation Manual. | Check the vacuum status |
| Turbo speed less than 100% p.20 ↗ | Large leaks in the system. | Check vacuum connections, transfer line seating, vent valve seal, and analyzer assembly seating. | Check the vacuum status |
| Increase in pump current after at 100% or in ion gauge pressure p.20 ↗ | Small leaks in the system. | Diagnose small leaks by observing changes in ion gauge reading and pinpoint using leak check section in method Service.mth. | Check the vacuum status |
| Roughing pump continues to gurgle after about 10 to 20 seconds p.19 ↗ | Analyzer assembly not seated properly, transfer line not seated in trap, or vent valve not sealed. | Verify analyzer assembly is seated properly on manifold (no gaps), transfer line is seated in trap, and vent valve is sealed. | Initial Pump down |
| Failure to reach 100% pump speed in a reasonable time p.23 ↗ | Vacuum leak. | Take corrective action; see appropriate Troubleshooting section in 240 GC/MS Ion Trap Hardware Operation Manual. | Startup and shutdown |
| Not Ready message at top of screen p.14 ↗ | GC or AutoSampler not ready. | Wait until GC and AutoSampler come to ready state; message changes to Ready. Check individual ready states under Windows pull-down menu. | Acquiring Data |
| Auto tune generates an error message and restores last values in the instrument p.28 ↗ | Electron lens tuning failed to find best voltage setting; balance outside range of 200 to 300 µA. | Check electron lens balance; algorithm searches optimal values by changing four variables one at a time. | Electron lens tuning |
| Too high a pressure of air or water in the system p.27 ↗ | Air leak or need to bake out the system. | Perform Air/Water Check; results in poor performance. Bake out system if needed. | Air/water check |
Technical Data
| Parameter | Value | Condición |
|---|---|---|
| Turbo pump speed | 100 % p.20 ↗ | Typical operating range, External mode |
| Pump current | 200 to 300 mAmps p.20 ↗ | Typical operating range, External mode |
| Power | 9 to 13 Watts p.20 ↗ | Typical operating range, External mode |
| Ion gauge pressure | < 20 µTorr p.20 ↗ | Typical operating range, External mode |
| Roughing line pressure | < 50 mTorr p.20 ↗ | Typical operating range, External mode |
| Default RF storage level | 35 u p.8 ↗ | Hybrid mode |
| Helium buffer gas flow rate | 1 mL/min p.9 ↗ | Ion storage |
| Initial helium buffer gas flow rate | 3 to 4 mL/min p.21 ↗ | Starting the instrument |
| Damping gas flow rate | 0.5 mL/min p.20 ↗ | Start damping gas flow |
| CI gas restrictor flow | 50 mL/min p.13 ↗ | Methane CI installation |
| Methane regulator second stage pressure | 20 psi p.13 ↗ | Methane CI installation |
| CI gas adjustment ion gauge pressure | 70 to 100 µTorr p.13 ↗ | CI gas adjustment |
| Conversion dynode voltage, positive mode | -10,000 V p.11 ↗ | Positive modes |
| Conversion dynode voltage, negative mode | +10,000 V p.11 ↗ | Negative mode |
| Electron multiplier gain | ~10^5 p.11 ↗ | Signal amplification |
| Electron multiplier gain for Air/Water Check | 10^5 p.27 ↗ | Air/Water Check |
| Electron lens balance range | 200 to 300 µA p.28 ↗ | Electron lens tuning |
| Default manifold temperature | 50 °C p.22 ↗ | System temperatures |
| Transfer line temperature offset below max column temperature | 20 °C p.22 ↗ | Set system temperatures |
| Turbo pump speed at shutdown | 35 % of full speed p.24 ↗ | Shutting down the system |
| Temperature threshold before main power off | 80 °C p.24 ↗ | Shutting down the system |
| Minimum vent time | 5 minutes p.24 ↗ | Shutting down the system |
| Wait time after bakeout before AutoTune | 2 hours p.22 ↗ | System bakeout |
| Ion trap temperature stabilization before mass calibration | 2 hours p.29 ↗ | Mass calibration |
| Scan rate, Normal mode | 5000 u/sec p.37 ↗ | Normal scan mode |
| Scan rate, Fast mode | 10000 u/sec p.37 ↗ | Fast scan mode |
| Scan rate, Fastest mode | 10000 u/sec p.37 ↗ | Fastest scan mode, Full scan only |
| Maximum number of chromatographic time segments | 250 p.36 ↗ | Runs up to 650 minutes |
| Maximum run length for time segments | 650 minutes p.36 ↗ | Chromatographic time segments |
| Profile data collection points | 10 points per m/z p.36 ↗ | Profile data |
| Default Target TIC for CI | 5,000 counts p.39 ↗ | Positive or negative chemical ionization |
| Maximum Target TIC | 65,000 counts p.39 ↗ | Ionization control |
| Typical Target TIC for best results | 20,000 to 40,000 counts p.39 ↗ | Full scan acquisitions |
| Maximum fixed ion time | 65,000 µsec p.39 ↗ | Customize fixed ion time experiments |
| Default Ejection Amplitude | 15 V p.40 ↗ | High mass isolation of CI reagent ions |
| Max Reaction Time range | 1 to 2000 µsec p.40 ↗ | Hybrid parameters |
| Isolation Window range | 1.0 to 14.0 m/z p.42 ↗ | MS/MS parameters |
| Default Isolation Window | 3.0 m/z p.42 ↗ | MS/MS parameters |
| Low Edge Offset range | -0.5 to 0.5 m/z p.43 ↗ | MS/MS parameters |
| High Edge Offset range | -0.5 to 0.5 m/z p.43 ↗ | MS/MS parameters |
| Default High Mass Ejection amplitude | 35 volts p.43 ↗ | MS/MS parameters |
| Multiplier Offset adjustment range | up to 300 V p.38 ↗ | General parameters tab |
| Default Count Threshold | 1 counts p.38 ↗ | General parameters tab |
| Mass calibration ions (PFTBA) | 69, 131, 264, 414, 464, 614 m/z p.29 ↗ | Mass calibration |
| Ion lens tuning cal gas ions | 131 and 414 m/z p.29 ↗ | Ion lens tuning |
| Trap DC offset optimization ion | 414 m/z p.29 ↗ | Trap DC offset voltage |