Induztr
Resumen técnico Visor de documentos Modelos relacionados

Agilent 6475 Triple Quad LC/MS System User Guide

Technical Reference Summary

Covered Models & Document Scope

Cubre el sistema Agilent 6475A Triple Quad LC/MS con las fuentes de ionización compatibles: Agilent Jet Stream (AJS) ESI, Electrospray Ionization (ESI), Atmospheric Pressure Chemical Ionization (APCI), Multimode Ionization (MMI) y Nanospray ESI. Válido para MassHunter 12.0 hasta que sea reemplazado.

Section-by-Section Technical Breakdown

pp. 14-25
Descripción general del hardware

Describe la vista frontal del 6475A LC/TQ e identifica la fuente de ionización, el panel de servicio, el interruptor de alimentación, la cubierta frontal, el indicador de estado, la botella CDS y el número de serie. También enumera las fuentes de ionización compatibles y su referencia de mantenimiento.

  • Front panel includes ion source, service panel, power switch, front cover, status indicator, CDS bottle, and serial number.
  • Supported sources: AJS, ESI, APCI, MMI, and Nanospray ESI.
pp. 18-19
Luces del indicador de estado del instrumento y estados de adquisición

Define los estados del instrumento y los colores/patrones de parpadeo correspondientes del LED de estado y del LED del interruptor de alimentación, y explica la ventana Instrument Status codificada por colores en el programa Acquisition. También detalla qué ocurre en el modo Standby para los calentadores de la fuente, los flujos de gas y los voltajes.

  • Status LED and Power Switch LED states are mapped for BOOTING, ACQUISITION, FAULT, PUMPING DOWN, VENTING, STANDBY, Vented, IDLE, POWERING DOWN, BACKGROUND SCAN, and Off.
  • In Standby, source and ion optics voltages are off, spectra are not sent, and AJS sheath gas temperature, drying gas flow, and drying gas temperature are reduced.
  • Instrument Status window colors: Gray Offline, Yellow Unknown, Dark Yellow Not Ready, Green Idle, Teal Standby, Purple Pre-run/Injecting, Blue Running/Post Run, Orange Tuning, Light Orange Not Ready, Red Instrument Error, Blank Disconnected.
pp. 26-33
Sintonización (Checktune y Autotune)

Explica el propósito y la duración de Checktune y Autotune, la mezcla de sintonización correcta para cada tipo de fuente y cómo programar sintonizaciones automáticas semanales o mensuales. Checktune verifica el ancho de pico y el eje de masas; Autotune se ejecuta después del mantenimiento preventivo o si Checktune falla.

  • Checktune takes approximately 3 minutes per polarity.
  • Autotune takes approximately 15 to 20 minutes per polarity.
  • Tuning mixes: ESI-L for ESI and AJS ESI, MMI-L for MMI, APCI-L for APCI.
  • Scheduling supports Weekly or Monthly recurrence.
pp. 34-62
Operación básica

Cubre el arranque y la parada, el venteo, el inicio del software Acquisition, el uso de las ventanas de Acquisition, la preparación de los módulos LC y del Triple Quad LC/MS, la configuración de métodos de adquisición, la ejecución de muestras individuales y listas de trabajo, y la revisión de resultados. Incluye el System Activity Log para la solución de errores.

  • Vent sequence turns off spray chamber high voltages, drying gas heater, nebulization flow, detector, and lens voltages; drying gas flow is set to Standby; rough pump turns off when turbo speed is below 20 percent.
  • Wait until the instrument completely vents (760 Torr) before shutting down.
  • Switch LC stream to Waste when not acquiring data; switch to MS after column conditioning and tuning.
  • Method Optimizer can automate MRM product ion selection, collision energies, fragmentor voltages, and source parameters.
  • dMRM Method Split window splits methods with many dMRM transitions into separate methods with fewer transitions.
pp. 63-90
Mantenimiento

Proporciona procedimientos de mantenimiento rutinario y periódico para el sistema de suministro de calibrador y la válvula de desvío, las fuentes de ionización, el nebulizador, la aguja de corona, el inyector de iones y la bomba rough, además de la desinfección. Especifica intervalos, herramientas, piezas y precauciones para cada tarea.

  • Check calibrant levels monthly, or weekly if tuning frequently; refill if the tuning mix level is within a few millimeters of the intake tube end.
  • Clean the spray chamber daily or at the end of each shift; perform weekly cleaning if contamination persists or if the spray shield or capillary cap show significant discoloration.
  • Flush the nebulizer daily for 3 minutes and monthly overnight using 30% to 70% methanol in water.
  • Tuning mixes are not interchangeable; changing source or inlet assembly without changing the tuning mix can cause miscalibration and mass assignment errors.
  • After changing to a source that uses a different tuning mix, run calibrant for 5 minutes, perform Checktune, and run Autotune if Checktune results are not acceptable.

Key Integration, Operating & Safety Requirements

Specification / Condition Engineering Implication Aplica a
El rango de temperatura de operación es de 15°C a 35°C; el rango de temperatura de almacenamiento es de -40°C a 70°C. p.2 ↗ Ensure the laboratory ambient temperature stays within 15–35°C during operation to maintain instrument performance and avoid condensation or overheating. 6475A LC/TQ system
Checktune tarda aproximadamente 3 minutos por polaridad y verifica el ancho de pico y el eje de masas. p.27 ↗ Schedule Checktune before acquisitions to confirm mass assignment and sensitivity are within expectations without a long interruption. 6475A LC/TQ system
Autotune tarda aproximadamente 15 a 20 minutos por polaridad y solo es necesario después del mantenimiento preventivo o si Checktune muestra un problema. p.27 ↗ Plan maintenance windows of at least 30–40 minutes for a full two-polarity Autotune. 6475A LC/TQ system
Selección de mezcla de sintonización: ESI-L Low Concentration Tuning Mix para ESI y AJS ESI; MMI-L Low Concentration Tuning Mix para MMI; APCI-L Low Concentration Tuning Mix para APCI. p.27 ↗ Use the correct tuning mix for the installed source; using the wrong mix can cause miscalibration and mass assignment errors. 6475A LC/TQ with ESI, AJS, MMI, or APCI source
Al ventear, la bomba rough se apaga cuando la velocidad del turbo está por debajo del 20 por ciento, y el sistema debe alcanzar 760 Torr antes del apagado. p.37 ↗ Do not power off or unplug the instrument until venting is complete at 760 Torr to avoid turbo pump damage. 6475A LC/TQ system
Después del venteo y el apagado, desenchufe el cable de alimentación principal detrás del panel de servicio para evitar que los componentes de la bomba turbo se sobrecalienten. p.37 ↗ Include unplugging the main power cable in the shutdown procedure for extended idle periods. 6475A LC/TQ system
En el modo Standby, la interfaz de la fuente permanece encendida, el gas de secado permanece caliente y los flujos del nebulizador se mantienen, pero los voltajes de la fuente y de la óptica de iones están apagados y el espectrómetro de masas deja de enviar espectros. p.19 ↗ Use Standby when changing the ion source or when the instrument is not in use to keep the source warm while safely removing high voltage. 6475A LC/TQ system
Para la fuente AJS en Standby, se reducen la temperatura del gas de vaina, el flujo de gas de secado y la temperatura del gas de secado; para las fuentes APCI y multimodo, los calentadores del gas vaporizador se reducen. p.19 ↗ Expect longer equilibration times after returning from Standby, especially for APCI/MMI vaporizer and AJS sheath gas temperatures. 6475A LC/TQ with AJS, APCI, or MMI source
Verifique los niveles de calibrador mensualmente, o semanalmente si sintoniza con frecuencia; rellene cuando el nivel de la mezcla de sintonización esté a pocos milímetros del extremo del tubo de admisión. p.64 ↗ Low calibrant can cause failed tunes; maintain sufficient volume to keep the intake tube immersed. 6475A LC/TQ calibrant delivery system
Limpie la cámara de pulverización diariamente o al final de cada turno usando una mezcla 50:50 de isopropanol de grado LC/MS y agua de grado LC/MS. p.65 ↗ Daily cleaning reduces carryover contamination between samples and analyses. 6475A LC/TQ ion source
La limpieza semanal de la cámara de pulverización usa papel abrasivo de grano 4000 y sonicación durante 5 minutos en isopropanol/agua 50:50. p.66 ↗ Perform weekly cleaning when daily cleaning does not resolve contamination or when the spray shield or capillary cap show significant discoloration. 6475A LC/TQ ion source
Enjuague el nebulizador diariamente durante 3 minutos y mensualmente durante la noche usando 30% a 70% de metanol en agua. p.68 ↗ Regular flushing removes traces of samples and buffers from tubing, valves, and nebulizer, reducing back pressure and spray instability. 6475A LC/TQ nebulizer
Después de cambiar a una fuente que usa una mezcla de sintonización diferente, ejecute el calibrador durante 5 minutos, realice Checktune y ejecute Autotune si los resultados de Checktune no son aceptables. p.70 ↗ This sequence ensures the instrument is correctly calibrated for the new source before acquiring data. 6475A LC/TQ when changing source type
Antes de retirar una fuente ESI o AJS, ponga el sistema en Standby, ajuste la temperatura del gas lo más baja posible y deje el flujo de gas encendido durante 30 minutos para enfriar la fuente. p.70 ↗ Cooling prevents burns from hot source components and protects the source from thermal stress during removal. 6475A LC/TQ with ESI or AJS source
Para la instalación del escudo de pulverización ESI, el orificio pequeño debe estar en la parte superior (posición de las 12 en punto); use un destornillador Torx T10 para aflojar los dos tornillos de la placa extrema y girar el escudo en sentido horario. p.72 ↗ Correct spray shield orientation is required for proper nebulization and spray stability. 6475A LC/TQ with ESI source
Para la instalación de la fuente Multimodo, los pasadores deben estar en las posiciones de las 6 y 9 en punto. p.73 ↗ Incorrect dowel orientation can prevent proper seating of the spray chamber and cause leaks or poor performance. 6475A LC/TQ with Multimode source
El procedimiento de ajuste del nebulizador requiere el G1960-67470 Nebulizer Adjustment Kit y se indica por un aumento de la contrapresión del LC, pulverización fuera de eje, goteo del nebulizador o cuando la aguja del nebulizador de referencia no está pulverizando. p.75 ↗ Use the adjustment kit to inspect and correct nebulizer needle position when these symptoms appear. 6475A LC/TQ nebulizer
El System Activity Log en el programa Acquisition proporciona información sobre errores para ayudar con la solución de problemas. p.51 ↗ Check the System Activity Log first when diagnosing instrument errors or unexpected behavior. 6475A LC/TQ system with MassHunter Acquisition
El Method Optimizer puede automatizar la selección de iones producto MRM, las energías de colisión, los voltajes del fragmentador y los parámetros de la fuente. p.43 ↗ Use Method Optimizer to reduce manual method development time for MRM transitions. 6475A LC/TQ system with MassHunter Workstation or Networked Workstation
La ventana dMRM Method Split facilita la división de métodos con muchas transiciones dMRM en métodos separados con menos transiciones dMRM. p.44 ↗ Use this window to manage method complexity and improve acquisition method performance when many transitions are required. 6475A LC/TQ system with MassHunter Workstation or Networked Workstation

Faults & Troubleshooting

Código / Síntoma Possible Cause Remedy Note
Status LED = Red; Power Switch LED = Green p.18 ↗ Instrument state = FAULT Check the System Activity Log for errors and troubleshoot accordingly. Table 1 Status indicator lights on instrument
Status LED = Blinking Red; Power Switch LED = Yellow p.18 ↗ Instrument state = VENTING Wait until the instrument completely vents (reaching 760 Torr) before proceeding. Table 1 Status indicator lights on instrument
Status LED = Red; Power Switch LED = Yellow p.18 ↗ Instrument state = Vented The instrument is vented; proceed with maintenance or restart as needed. Table 1 Status indicator lights on instrument
Status LED = Blinking Yellow; Power Switch LED = Yellow p.18 ↗ Instrument state = BOOTING (FPGA Loaded) Wait for boot to complete. Table 1 Status indicator lights on instrument
Status LED = Yellow; Power Switch LED = Green p.18 ↗ Instrument state = BOOTING (LINUX Loaded), STANDBY, or IDLE Wait for the instrument to reach the expected state; if IDLE, the instrument is ready. Table 1 Status indicator lights on instrument
Status LED = Blinking Green; Power Switch LED = Green p.18 ↗ Instrument state = ACQUISITION No action; the instrument is acquiring data. Table 1 Status indicator lights on instrument
Status LED = Green; Power Switch LED = Green p.18 ↗ Instrument state = BACKGROUND SCAN No action; the instrument is in background scan. Table 1 Status indicator lights on instrument
Status LED = Off; Power Switch LED = Blinking Yellow p.18 ↗ Instrument state = POWERING DOWN Wait for power-down to complete. Table 1 Status indicator lights on instrument
Status LED = Off; Power Switch LED = Off p.18 ↗ Instrument state = Off Turn on the instrument power switch to start. Table 1 Status indicator lights on instrument
Red - Instrument Error p.19 ↗ The instrument has an error and cannot process samples. View the System Activity Log for events and errors to identify the cause. Instrument Status Indicators in Acquisition
Dark Yellow - Not Ready p.19 ↗ The instrument is connected but is not ready to run (for example, not reaching the correct temperature or pressure required by the method). Wait for the instrument to reach the required temperature or pressure setpoints. Instrument Status Indicators in Acquisition
Light Orange - Not Ready p.19 ↗ The device is not ready. Check device status and method requirements. Instrument Status Indicators in Acquisition
Yellow - Unknown p.19 ↗ The device is in an unknown run state. Check the System Activity Log and device connection. Instrument Status Indicators in Acquisition
Blank - Disconnected p.19 ↗ The connection to the instrument has been closed. Reconnect the instrument in the Acquisition software. Instrument Status Indicators in Acquisition
Increased LC back pressure, off-axis spraying, dripping from the nebulizer, or reference nebulizer needle not spraying p.75 ↗ Nebulizer needle requires inspection/adjustment. Perform nebulizer inspection using the G1960-67470 Nebulizer Adjustment Kit. Inspecting the nebulizer

Technical Data

Parameter Value Condición
Operating temperature 15 to 35 °C p.2 ↗
Storage temperature -40 to 70 °C p.2 ↗