Induztr
Resumen técnico Visor de documentos Modelos relacionados

Operating Instructions — VCS 100 vacuum pump (BA 237-EN, ed. 1.1 05/07/2022, EN)

Technical Reference Summary

Covered Models & Document Scope

Este documento abarca las bombas de vacío rotativas de paletas lubricadas con aceite V-VCS 100, V-VCS 150, V-VCX 100 y V-VCX 150. V-VCS es el diseño estándar; V-VCX es la variante con mayor compatibilidad con vapor de agua (piezas funcionales más resistentes, paletas de epoxy reforzado con fibra de vidrio, mayor cantidad de lastre de gas, mayor temperatura del cárter de aceite).

Section-by-Section Technical Breakdown

pp. 14-16
Descripción general del producto y funcionamiento

Describe el diseño rotativo de paletas de una etapa lubricado con aceite, los componentes principales y la placa de características. Explica el filtro de malla integrado, el separador de niebla de aceite, la válvula de retención, la válvula de lastre de gas y el accionamiento por acoplamiento. Cubre las características de la variante V-VCX y la válvula de lastre de gas ajustable.

  • Single-stage oil-flooded rotary vane vacuum pump; oil seals gaps, lubricates and dissipates compression heat.
  • Integrated mesh filter on suction side; oil and oil mist separator on outlet side returns oil to circulation.
  • Integrated non-return valve prevents ventilation of the evacuated system for approx. 2 minutes after stop.
  • Standard gas ballast valve prevents condensation of low quantities of water vapour at operating temperature.
  • V-VCX: functional parts more resistant to water steam and solvents; glass-fibre reinforced epoxy slide gates; increased gas ballast quantity; higher oil sump temperature.
  • V-VCX includes an additional adjustable gas ballast valve with ball valve.
pp. 16
Campos de aplicación

Define los rangos de presión de aspiración admisibles para vacío continuo y evacuación de sistemas cerrados. Indica las capacidades de bombeo nominales y señala la selección del motor para funcionamiento continuo por encima de 100 mbar (abs.).

  • Nominal pumping capacity at 50 Hz: 100 m³/h (VCS 100) and 150 m³/h (VCS 150).
  • Continuous vacuum intake pressure range: V-VCS 0.5 to 500 mbar (abs.); V-VCX 3.0 to 500 mbar (abs.).
  • For evacuating closed systems, volume to be evacuated must be no more than 2% of nominal pumping capacity.
  • For continuous operation > 100 mbar (abs.), use next higher motor output.
  • Frequent switching (approx. 10 times per hour) or high ambient/inlet temperatures may exceed motor winding and bearing temperature limits.
pp. 17-19
Instalación

Cubre la preparación, la instalación mecánica, la conexión de tuberías, la comprobación del aceite y la conexión del motor. Especifica los requisitos de espacio, la alineación horizontal, las distancias libres para el aire de refrigeración y los requisitos de protección eléctrica.

  • Provide at least 40 cm space around the machine for maintenance.
  • Machine must be set up horizontally; max. inclination 1° in all directions.
  • Cooling air inlets and outlets must be at least 30 cm from adjacent walls.
  • Ambient temperature: min. +12 °C, max. +40 °C.
  • Exhaust air opening must not be closed or restricted; no filter on exhaust side; back pressure only up to +100 mbar.
  • For parallel operation, install an external non-return valve in the suction line upstream of each pump.
  • Electrical installation per EN 60204 by qualified electrician; motor protection switch and main switch installed by operating company.
  • Motor protection class IP 55, insulation class F; permissible tolerances ±5% voltage and ±2% frequency.
pp. 20-22
Puesta en marcha y puesta fuera de servicio

Describe las comprobaciones de arranque, la comprobación del sentido de giro, la comprobación del nivel de aceite, las medidas durante la parada, la puesta fuera de servicio y la puesta en servicio de nuevo. Enfatiza la verificación de la instalación antes del arranque.

  • Installation check before start-up: no transport damage, safe horizontal standing, correct and leak-tight pipe connections, tight screw/flange connections, compliant electrical installation.
  • Check motor rotation direction against direction of rotation arrow on motor flange.
  • Check oil level through oil sight glass and top up if necessary.
  • For standstill times longer than two minutes, vent the connected suction line to atmospheric pressure.
pp. 23-31
Mantenimiento y reparación

Proporciona la tabla de mantenimiento y los procedimientos para la limpieza, el mantenimiento del aceite, los elementos separadores de aceite, el ventilador, el motor y el acoplamiento. Especifica la viscosidad del aceite y los intervalos de mantenimiento.

  • Lubricating oil viscosity must comply with ISO VG 100 as per DIN ISO 3448.
  • Clean mesh filter in suction flange and filter cartridge of gas ballast valve.
  • Change oil separator elements when dirty.
  • Check fan for dirt and damage; clean ventilation slots.
  • Check coupling and coupling sleeve for wear; replace if defective.
  • Repairs only by authorised workshops using original spare parts.
pp. 33-35
Errores

Contiene una tabla de fallos con causas y soluciones. Cubre los disparos de la protección del motor, la capacidad de bombeo insuficiente, la falta de alcance de la presión final, el sobrecalentamiento, la niebla de aceite en el escape, el ruido anómalo y el agua en el aceite.

  • Never restart pump after automatic shut-off without finding and remedying the cause.
  • Motor protection switch must be suitable for short-term excess current at start-up (IEC 60947-4-1).
  • Oil viscosity must comply with ISO VG 100 as per DIN ISO 3448.
  • Back pressure in exhaust line must be checked if capacity or final pressure problems occur.
  • Water in oil: install water interceptor upstream or let pump run with closed suction side to evaporate water.
pp. 37
Datos técnicos

Remite al capítulo 10 para los datos técnicos, incluidos el peso, el nivel de presión sonora y los datos eléctricos. La hoja de datos D 237 contiene los datos técnicos y las curvas características.

  • Technical data are provided in chapter 10 of the manual.
  • Data sheet D 237 shows dependency of pumping capacity on intake pressure.
  • Sound pressure level measured as per EN ISO 3744.

Key Integration, Operating & Safety Requirements

Specification / Condition Engineering Implication Aplica a
El rango de temperatura ambiente y de entrada admisible es de 12 a 40 °C. p.8 ↗ Operation outside this range requires consultation with the manufacturer; ensure installation room ventilation and temperature control. V-VCS 100/150 and V-VCX 100/150
Rango de presión de aspiración continua: V-VCS 0,5 a 500 mbar (abs.); V-VCX 3,0 a 500 mbar (abs.). p.16 ↗ Select pump variant based on required process vacuum; operating outside these ranges risks oil leakage through outlet. V-VCS and V-VCX
Para la evacuación de sistemas cerrados, el volumen a evacuar no debe ser superior al 2 % de la capacidad de bombeo nominal. p.16 ↗ Size the pump so that the connected closed volume does not exceed 2% of the pump's nominal capacity to avoid excessive evacuation time or oil carry-over. V-VCS 100/150 and V-VCX 100/150
Para funcionamiento continuo > 100 mbar (abs.), debe utilizarse la siguiente potencia de motor superior. p.16 ↗ When specifying a pump for continuous duty above 100 mbar, select a larger motor to avoid overheating. V-VCS 100/150 and V-VCX 100/150
La contrapresión máxima admisible en el lado de escape es +100 mbar. p.18 ↗ Exhaust piping and any connected equipment must not create back pressure exceeding +100 mbar; no filter may be installed on the exhaust side. V-VCS 100/150 and V-VCX 100/150
La máquina debe instalarse horizontalmente con una inclinación máxima de 1° en todas las direcciones. p.17 ↗ Ensure the floor is plane and even; secure the machine against tipping over and falling. V-VCS 100/150 and V-VCX 100/150
Las entradas y salidas de aire de refrigeración deben estar al menos a 30 cm de las paredes adyacentes. p.17 ↗ Maintain clearance to prevent recirculation of hot exhaust air and ensure sufficient cooling. V-VCS 100/150 and V-VCX 100/150
Debe preverse un espacio de al menos 40 cm alrededor de la máquina para los trabajos de mantenimiento. p.17 ↗ Installation layout must allow access to suction flange, oil filling point, oil sight glass, oil drain, gas ballast and de-oiler housing. V-VCS 100/150 and V-VCX 100/150
Datos eléctricos del motor: clase de protección IP 55, clase de aislamiento F, diseñado según DIN EN 60034. p.19 ↗ Verify motor data plate matches mains supply; use appropriate motor protection switch. V-VCS 100/150 and V-VCX 100/150
Desviación de tensión admisible ±5 % y desviación de frecuencia ±2 %. p.19 ↗ Ensure mains supply quality is within these tolerances to avoid loss of power or motor damage. V-VCS 100/150 and V-VCX 100/150
La viscosidad del aceite lubricante debe cumplir con ISO VG 100 según DIN ISO 3448. p.26 ↗ Use only oil of the specified viscosity grade; incorrect viscosity can cause overheating, insufficient lubrication or poor vacuum. V-VCS 100/150 and V-VCX 100/150
Para el funcionamiento en paralelo de varias bombas, debe instalarse una válvula de retención externa en la línea de aspiración aguas arriba de cada bomba. p.18 ↗ Prevents a switched-off pump from being damaged by suction capacity of operating pumps. V-VCS 100/150 and V-VCX 100/150
Para tiempos de parada superiores a dos minutos, ventile la línea de aspiración conectada a la presión atmosférica. p.18 ↗ Provide an air release position (e.g. ball valve) in the suction line to avoid possible damage to the machine. V-VCS 100/150 and V-VCX 100/150
Capacidad de bombeo nominal a 50 Hz: 100 m³/h (VCS 100) y 150 m³/h (VCS 150). p.16 ↗ Use these values for sizing; actual capacity depends on intake pressure (see data sheet D 237). V-VCS 100 and V-VCS 150
Rango de temperatura de almacenamiento: -10 °C a +60 °C; humedad relativa del aire máx. 80 %; almacenar sin polvo, seco, sin vibraciones y protegido de la radiación solar. p.13 ↗ For long-term storage (>3 months), use preservation oil instead of operating oil; do not store for more than 6 months. V-VCS 100/150 and V-VCX 100/150
El interruptor de protección del motor debe tener una desconexión retardada dependiente de la sobrecarga considerando la sobrecorriente breve en el arranque (versión con disparo por cortocircuito y sobrecarga según IEC 60947-4-1). p.33 ↗ Select motor protection switch suitable for cold-start excess current to avoid nuisance tripping. V-VCS 100/150 and V-VCX 100/150
Se aprecia una reducción de la potencia cuando se instala a más de 1000 m sobre el nivel del mar. p.17 ↗ Contact manufacturer for installations at high altitude to account for reduced cooling and motor performance. V-VCS 100/150 and V-VCX 100/150
La válvula de retención impide la ventilación del sistema evacuado durante aprox. 2 minutos después de que la bomba se haya detenido. p.15 ↗ Do not rely on the non-return valve for long-term isolation; use external valves if longer hold times are required. V-VCS 100/150 and V-VCX 100/150

Faults & Troubleshooting

Código / Síntoma Possible Cause Remedy Note
Machine is switched off by the motor protection switch p.33 ↗ Mains voltage/ Frequency does not correspond with the motor data Check by qualified electrician Chapter 5.5
Machine is switched off by the motor protection switch p.33 ↗ Connection to motor terminal board is not correct Check by qualified electrician Chapter 5.5
Machine is switched off by the motor protection switch p.33 ↗ Motor protection switch is not set correctly Check by qualified electrician Chapter 5.5
Machine is switched off by the motor protection switch p.33 ↗ Motor protection switch is triggered too quickly Use a motor protection switch with an overload-dependent delayed switch off that takes into consideration the short term excess current at start up (version with short circuit and overload trigger as per IEC 60947-4-1)
Machine is switched off by the motor protection switch p.33 ↗ Vacuum pump or its oil is too cold Note the ambient temperature and the inlet temperature Chapter 2.4
Machine is switched off by the motor protection switch p.33 ↗ The lubricating oil is too viscous The oil viscosity must comply with ISO VG 100 as per DIN ISO 3448 Chapter 7.6
Machine is switched off by the motor protection switch p.33 ↗ The oil separator elements are dirty. Change the oil separator elements Chapter 7.7
Machine is switched off by the motor protection switch p.33 ↗ The back pressure in the exhaust line is too high Check the hose and/or the pipe Chapter 5.3
Machine is switched off by the motor protection switch p.33 ↗ Permanent operation >100 mbar (abs.). Use next largest motor output Chapter 4.4
Pumping capacity is insufficient p.33 ↗ The inlet pipe is too long or too narrow Check the hose and/or the pipe Chapter 5.3
Pumping capacity is insufficient p.33 ↗ Leak on the inlet side of the vacuum pump or in the system Check the pipework and screw connections for leaks and check for tight fit Chapter 7.2
Pumping capacity is insufficient p.33 ↗ The intake filter is dirty Clean or replace the intake filter Chapter 7.5
Final pressure (max. vacuum) is not reached p.34 ↗ Leak on the inlet side of the vacuum pump or in the system Check the pipework and screw connections for leaks and check for tight fit Chapter 7.2
Final pressure (max. vacuum) is not reached p.34 ↗ Incorrect oil viscosity The oil viscosity must comply with ISO VG 100 as per DIN ISO 3448 Chapter 7.6
Machine gets too hot p.34 ↗ Ambient or inlet temperatures too high Ensure proper use Chapter 2.4
Machine gets too hot p.34 ↗ Cooling air supply is obstructed Check ambient conditions Chapter 5.1
Machine gets too hot p.34 ↗ Cooling air supply is obstructed Clean ventilation slots Chapter 7.8
Machine gets too hot p.34 ↗ Fan dirty and damaged Clean the fan, replace the fan, if necessary Chapter 7.8
Machine gets too hot p.34 ↗ The lubricating oil is too viscous The oil viscosity must comply with ISO VG 100 as per DIN ISO 3448 Chapter 7.6
Machine gets too hot p.34 ↗ The oil separator elements are dirty. Change the oil separator elements Chapter 7.7
Machine gets too hot p.34 ↗ The back pressure in the exhaust line is too high Check the hose and/or the pipe Chapter 5.3
Exhaust air contains visible oil mist p.34 ↗ The oil separator elements are not inserted correctly or the O rings are missing. Check that it is correctly seated Chapter 7.7
Exhaust air contains visible oil mist p.34 ↗ Unsuitable oil is being used Use suitable types Chapter 7.6
Exhaust air contains visible oil mist p.34 ↗ The oil separator elements are dirty Change the oil separator elements Chapter 7.7
Exhaust air contains visible oil mist p.34 ↗ Ambient or inlet temperatures too high Ensure proper use Chapter 2.4
Exhaust air contains visible oil mist p.34 ↗ Cooling air supply is obstructed Check ambient conditions Chapter 5.1
Exhaust air contains visible oil mist p.34 ↗ Cooling air supply is obstructed Clean ventilation slots Chapter 7.2
The machine makes a strange noise (The blades making a hammering noise when starting from cold is normal if it disappears within two minutes as the operating te p.34 ↗ The pump housing is worn (chatter marks) Repair by manufacturer or authorised workshop Elmo Rietschle Service
The machine makes a strange noise (The blades making a hammering noise when starting from cold is normal if it disappears within two minutes as the operating te p.34 ↗ The vacuum adjustment valve (if available) is vibrating Replace the valve Chapter 7.11
The machine makes a strange noise (The blades making a hammering noise when starting from cold is normal if it disappears within two minutes as the operating te p.34 ↗ The Blades are damaged Repair by manufacturer or authorised workshop Elmo Rietschle Service
The machine makes a strange noise (The blades making a hammering noise when starting from cold is normal if it disappears within two minutes as the operating te p.34 ↗ Vacuum pump or its oil is too cold Note the ambient temperature and the inlet temperature Chapter 2.4
The machine makes a strange noise (The blades making a hammering noise when starting from cold is normal if it disappears within two minutes as the operating te p.34 ↗ The lubricating oil is too viscous The oil viscosity must comply with ISO VG 100 as per DIN ISO 3448 Chapter 7.6
The machine makes a strange noise p.34 ↗ Coupling defective or coupling sleeve worn out Check and replace coupling / coupling sleeve Chapter 7.9.2
Water in lubricating oil p.35 ↗ Pump sucks in water Install water interceptor upstream of the pump —
Water in lubricating oil p.35 ↗ The pump sucks in more water vapour than is suitable for its water vapour compatibility Contact the manufacturer for increased gas ballast —
Water in lubricating oil p.35 ↗ Pump only works for a short time and therefore does not reach its normal operating temperature Let the pump continue to run with a closed suction side after extracting the water vapour until the water has evaporated from the oil —