Induztr
Resumen técnico Visor de documentos Modelos relacionados

Unichiller GL 100w Technical Data

Contenido

  1. Overview p. 1
    Product name and general introduction to the chiller unit
  2. Spec p. 2
    Technical data according to DIN 12876 standard
  3. p. 1 table, 31 rows

Unichiller GL 100w — Technical data according to DIN 12876

ParameterValue
Order-No.5502.0001.01
Operating temperature range-20...40 °C
temperature set point / display5,7" colour Touchscreen
Internal temperature sensorPt100
Sensor external connectionPt100
Temperature stability at -10°C0,2 K
Interface digitalEthernet, USB (Host u. Device), RS232
Safety classificationI / NFL
Cooling power at 20°C10 kW
Refrigeration machinewater-cooled, natural refrigerant
Refrigerant (ASHRAE, GHS)R-744 (A1, H280)
Global Warming Potential (GWP)1
Refrigerant quantity2,1 kg
CO2 equivalent0,0 t
UN-numberUN 2857
max. delivery50 l/min
max. delivery pressure3,5 bar
Pump connectionG1 1/4 male
Cooling water connectionG1/2 male
min. cooling water differential pressure1 bar
max. cooling water pressure6 bar
Volume of expansion10 l
Overall dimensions WxDxH **550x760x1455 mm
Power supply (3 Phase)400V 3~ 50Hz
max. current (3 Phase)7 A
Fuse (3 phase)3x16A
Pressure equipment categoryI
Degree of ProtectionIP20
min. ambient temperature5 °C
max. ambient temperature40 °C
from Serial-No.S611977

** Overall dimensions WxDxH

Engineering Facts

12 facts · every claim linked to a page
Installation

The chiller requires a three-phase 400 V supply with a 3x16 A fuse, so the site must provide a suitable three-phase feed.

Determines electrical supply and protection sizing during installation.

Source
“Power supply (3 Phase) 400V 3~ 50Hz”
Installation

The unit is water-cooled and needs cooling water at 1–6 bar differential pressure with G1/2 male connections.

Cooling water supply pressure and connection must be verified before installation.

Source
“min. cooling water differential pressure 1 bar”
Operation

Cooling water inlet must be kept between 5 °C and 20 °C, and pipes must be insulated if below the condensation point.

Operating outside this range risks condensation and reduced performance.

Source
“This temperature control unit is designed to operate with cooling water intake temperature between 5°C and 20°C.”
Performance

Rated 10 kW cooling power applies only at 20 °C room temperature, 15 °C cooling water inlet and 1 bar differential pressure.

Actual cooling capacity will differ if site conditions deviate from these reference values.

Source
“Output data valid for: Room temperature 20°C, cooling water inlet 15°C and 1 bar differential pressure between cooling water inlet and -”
Performance

Higher cooling water temperature reduces cooling power and may require increased cooling water flow.

Sizing of cooling water supply must account for derating at elevated water temperatures.

Source
“As the cooling water temperature increases, drop in the cooling power should be expected, and also an increased cooling water flow rate possible.”
Installation

Cooling water circuit materials include copper, stainless steel 1.4401, MS, PA, PPE, PTFE and EPDM, so only compatible water quality should be used.

Water chemistry must be compatible to avoid corrosion of these materials.

Source
“Materiels used in the cooling water circuit include; copper, Stainless steel 1.4401, MS, PA, PPE, PTFE and EPDM.”
Cumplimiento

Voltage tolerance is ±5% only with simultaneous frequency tolerance of ±2%, and certain combinations are not allowed.

Supply quality must be checked to avoid invalid voltage/frequency combinations.

Source
“Voltage + / - 5% with a simultaneous frequency tolerance of + / - 2%”
Installation

Three-phase devices below 63 A are delivered with cable but without a plug, so a plug must be provided on site.

Electrical installation planning must include a suitable plug for the supplied cable.

Source
“Three-phase devices with current consumption less than 63A --> with cable, without plug”
Safety

The unit uses R-744 refrigerant classified A1 with H280 hazard statement, requiring appropriate handling precautions.

Refrigerant safety classification affects handling and site safety requirements.

Source
“R-744 (A1, H280)”
Operation

Ambient temperature must remain between 5 °C and 40 °C for safe operation.

Room conditions must be controlled to stay within the permitted ambient range.

Source
“max. ambient temperature 40 °C”
Selection

The unit is intended for externally closed applications, which constrains how it can be integrated into the process.

Application type must match the closed-loop process design.

Source
“For externally closed applications.”
Cumplimiento

The equipment is classified Class A, Group 1 for electromagnetic disturbance to EN55011.

EMC class affects installation environment and potential interference considerations.

Source
“Classification (disturbance) to EN55011: Class A, Group 1”