7343000 Rev M Benchtop Freeze Dryers
Technical Reference Summary
Covered Models & Document Scope
Cubre los sistemas de liofilización de sobremesa Labconco FreeZone en tamaños de colector de 2,5 L, 4,5 L y 8 L con variantes de refrigeración de -50 °C, -84 °C y -105 °C. Prefijos de modelo/número de pieza: 70020xxxx (2,5L -50C), 70040xxxx (4,5L -50C), 70080xxxx (8L -50C), 71020xxxx (2,5L -84C), 71040xxxx (4,5L -84C), 72040xxxx (4,5L -105C). Se describen las variantes eléctricas de 115 V y 230 V; las cámaras de secado/múltiples y las bombas de vacío son accesorios suministrados por el usuario.
Section-by-Section Technical Breakdown
Define los circuitos eléctricos dedicados, los tipos de enchufe y los requisitos de espacio libre y ambiente para instalar el liofilizador. También especifica los requisitos de rendimiento y conexión de la bomba de vacío suministrada por el usuario.
- 115 V models require a 20 A dedicated single-phase circuit and a NEMA 5-20P grounded receptacle.
- 230 V models require a 15 A dedicated single-phase circuit and a grounded receptacle matching the supplied plug (US NEMA 6-15P, EU, China, UK, India).
- Frequency must agree with the serial tag rating; improper frequency will damage the compressor.
- Minimum 3" clearance between the back and both sides of the freeze dryer and adjacent walls; ideal ambient temperature is 23 °C.
- Vacuum pump: 98 L/min displacement and 0.007 mbar ultimate pressure is adequate for most samples; inlet must accept 3/4" ID hose.
- 115 V vacuum pumps need a 115 V, 15 A NEMA 5-15P plug; 230 V pumps need a reverse IEC plug.
Enumera los componentes enviados por modelo y describe el traslado y la instalación del liofilizador. Incluye la instalación del deflector requerida en los modelos -84 °C y -105 °C.
- Benchtop freeze dryers weigh 82–142 lbs (37–64 kg) depending on model; use at least two persons for manual lifting.
- Shipped components include vacuum hose 7373450, two hose clamps 1488800, drain hose 7205304 and a USB manual 1089005.
- Baffle 7419300 is supplied with -84 °C models; baffle 7208100 with -84 °C and -105 °C models.
- Baffle installs into the collector chamber with the flat flange upward and the arrow pointing toward the front of the freeze dryer.
- Operating system takes approximately 90 seconds to fully load after power-up.
Conexión paso a paso de la bomba de vacío suministrada por el usuario al liofilizador, incluida la verificación del nivel de aceite, la verificación de voltaje y las recomendaciones de filtración del escape.
- Use the supplied 3/4" ID vacuum hose and hose clamps; cut hose to length to allow gentle bends without kinks.
- Check vacuum pump oil level between the lines on the sight gauge before operation.
- Verify vacuum pump voltage setting agrees with the freeze dryer voltage on the serial number label.
- Connect the pump power cord to the receptacle labeled 'vacuum pump' on the back of the freeze dryer; 230 V models use a reverse IEC receptacle.
- An oil mist exhaust filter is highly recommended on rotary vane pumps; an oil return kit can return trapped oil to the pump.
Describe el montaje de cámaras de secado y múltiples en tapas de acrílico o acero inoxidable, incluidas las placas adaptadoras de cámara transparentes y la orientación de la junta.
- A drying chamber or manifold is purchased separately and positions above the 3-inch hole in the collector chamber lid.
- 12- or 16-port drying chambers install on acrylic and stainless steel lids with gasket lip facing down.
- 4- or 8-port manifolds install on acrylic or stainless steel lids.
- Clear drying chambers use their own bottom adapter plate in place of the supplied collector chamber lid.
Proporciona clasificaciones de compatibilidad de materiales para ácidos, tampones y disolventes comunes frente a vástagos de válvula, tapas de colector, mangueras/juntas/cuerpos de válvula, tapones de matraz y cámaras de acero inoxidable. Proporciona orientación sobre limpieza y mantenimiento del aceite de la bomba de vacío.
- Ratings: C = moderate degradation, limited use; D = severe degradation, infrequent use recommended with immediate thorough cleaning.
- Acrylic collector lids are rated D for acetone, acetonitrile, dioxane, methyl t-butyl ether and pyridine.
- Neoprene hoses, gaskets and valve bodies are rated D for acetic acid 20%, formic acid, TFA, acetone, acetonitrile, carbon tetrachloride, cyclohexane, dioxane, MTBE and pyridine.
- Stainless steel chambers and fittings are rated C only for pyridine; otherwise not listed as degraded.
- Vacuum pump oil must be changed if cloudy, particulate-laden or discolored; extended pump operation after a run with inlet blocked helps purge contaminants.
- Operating the pump at elevated vacuum level (>10 mbar) may expel oil and cause damage.
Describe el panel de control táctil, las indicaciones de estado LED, los parámetros de la pantalla de inicio y la estructura del menú. Define los umbrales de color para las lecturas de temperatura del colector y de vacío.
- On/Standby LED: 1 flash/s = initial power-up; slow pulse = screen in low-power mode; ON = active; Off = unplugged.
- Collector temperature displays RED above -40 °C (-50C models), -60 °C (-84C models) or -75 °C (-105C models); GREEN at or below those thresholds.
- Vacuum display reads 'High' if vacuum > 5 mbar; numerical value shown at ≤ 5 mbar.
- Vacuum value displays RED if > 1.500 mbar and GREEN if ≤ 1.500 mbar.
- Menu icons: Home, Programs, Data Logging, Settings, Sensors, Drying Accessory, End Point Detection, Help.
- Operation modes displayed: Standby, Manual, Program.
Cubre el ajuste del lastre de la bomba de vacío, el arranque automático y manual, el ajuste del nivel de vacío de operación, la preconcentración por congelación y la adición de muestras, el apagado y la descongelación.
- Operating vacuum level is set on the freeze dryer; higher vacuum set points increase the likelihood of oil mist exhaust.
- Samples with eutectic temperatures of -20 °C or lower should be added one flask at a time so vacuum can recover.
- If vacuum does not recover after adding a sample, system capacity has been exceeded and the sample should be removed.
- Freeze dry flask volume should be two to three times the sample volume; shell freezing maximizes surface area.
- Collector should be at least 15–20 °C colder than the sample eutectic temperature.
- A vacuum of 0.133 mbar or less is recommended for many applications.
Describe las alertas del sistema, incluidas falla de energía, rango de voltaje de línea, temperatura del colector, humedad del colector, mantenimiento de la bomba de vacío, fuga de vacío y punto de ajuste de vacío, además de la detección del punto final y la exportación del registro de datos.
- Alert conditions include Power Fail, Line Voltage Range, Collector Temp, Collector Moisture, Service Vacuum Pump, Vacuum Leak and Vacuum Set Point.
- End point detection is configured on its own screen.
- Data logs can be exported and downloaded via Ethernet.
Proporciona precauciones de seguridad para el servicio y un programa de mantenimiento rutinario para el liofilizador.
- Routine maintenance schedule is provided in Chapter 6.
- Service safety precautions must be followed before maintenance.
Proporciona puntos de referencia de rendimiento de vacío y procedimientos sistemáticos de aislamiento para la bomba de vacío, juntas/tuberías/conexiones/válvulas de muestra, componentes del sistema y cámara del colector, y funcionamiento del módulo de refrigeración.
- A clean, dry system without samples should reach 0.133 mbar within 10 minutes and ultimate vacuum of 0.040 mbar within 18 hours with refrigeration operating.
- Vacuum pump should achieve ultimate vacuum less than 0.010 mbar (approximately 10 microns) when deadheaded.
- Collector should reach design temperature (-50 °C, -84 °C or -105 °C) or lower within 30 minutes under no-load conditions.
- Leak isolation: cover the connection port with an inverted flask to test chamber/manifold; stopper the rear collector hole to test collector chamber vs. plumbing.
- Bulkhead fitting leaks on 4.5 L and 8 L models can be corrected by tightening the fitting or applying vacuum grease to the O-rings.
Los apéndices B y C proporcionan dibujos dimensionales, especificaciones eléctricas y condiciones ambientales para el liofilizador.
- Appendix B contains freeze dryer dimensions.
- Appendix C contains electrical specifications and environmental conditions.
Key Integration, Operating & Safety Requirements
| Specification / Condition | Engineering Implication | Aplica a |
|---|---|---|
| Los modelos de 115 V requieren un circuito dedicado monofásico de 20 A con un receptáculo con conexión a tierra NEMA 5-20P. p.11 ↗ | Verify site electrical capacity before installation; sharing the circuit may trip the breaker. | 115 V models |
| Los modelos de 230 V requieren un circuito dedicado monofásico de 15 A y un receptáculo con conexión a tierra que coincida con el enchufe suministrado (US NEMA 6-15P, EU, China, UK o India). p.11 ↗ | Confirm plug style at order and provide the matching receptacle. | 230 V models |
| La frecuencia debe coincidir con la clasificación de la placa de características; una frecuencia incorrecta dañará el compresor. p.12 ↗ | Check supply frequency against the serial tag before energizing. | whole series |
| Debe dejarse un espacio libre mínimo de 3" entre la parte posterior y ambos lados del liofilizador y las superficies de pared adyacentes; la temperatura ambiente ideal es de 23 °C. p.12 ↗ | Maintain airflow for refrigeration performance; performance is reduced as ambient temperature increases. | whole series |
| Una bomba de vacío con un desplazamiento de 98 L/min y una presión final de 0,007 mbar es adecuada para la mayoría de las muestras; la entrada debe aceptar una manguera de 3/4" de DI. p.12 ↗ | Select a user-supplied pump meeting these minimums and provide an exhaust filter to minimize oil mist. | whole series |
| Los liofilizadores de sobremesa pesan 82–142 lbs (37–64 kg) según el modelo. p.14 ↗ | Use at least two persons and safe lifting guidelines for manual handling. | whole series |
| El deflector 7419300 se suministra con los modelos -84 °C; el deflector 7208100 con los modelos -84 °C y -105 °C; instálelo con la brida plana hacia arriba y la flecha apuntando hacia adelante. p.18 ↗ | Correct baffle positioning is required to achieve maximum ice loading capability. | 71020xxxx, 71040xxxx, 72040xxxx |
| El sistema operativo tarda aproximadamente 90 segundos en cargarse completamente después del encendido; la pantalla permanece apagada durante los primeros 10–15 segundos. p.24 ↗ | Allow full boot time before assessing faults or operating the unit. | whole series |
| La temperatura del colector se muestra en ROJO por encima de -40 °C (modelos -50C), -60 °C (modelos -84C) o -75 °C (modelos -105C); VERDE en o por debajo de esos umbrales. p.25 ↗ | Use color indication to confirm collector is ready before adding samples. | whole series |
| La pantalla de vacío muestra 'High' si el vacío > 5 mbar; el valor numérico se muestra a ≤ 5 mbar; ROJO si > 1,500 mbar, VERDE si ≤ 1,500 mbar. p.26 ↗ | Interpret displayed vacuum status against these thresholds for process readiness. | whole series |
| El colector debe estar al menos 15–20 °C más frío que la temperatura eutéctica de la muestra; se recomienda un vacío de 0,133 mbar o menos para muchas aplicaciones. p.9 ↗ | Select collector temperature variant based on sample eutectic temperature. | whole series |
| Las muestras con temperaturas eutécticas de -20 °C o inferiores deben colocarse en el sistema un matraz a la vez para que el vacío pueda recuperarse; si el vacío no se recupera, se ha superado la capacidad. p.10 ↗ | Load such samples sequentially and monitor vacuum recovery to avoid overloading the collector and pump. | whole series |
| El volumen del matraz de liofilización debe ser de dos a tres veces el volumen de la muestra; la congelación en capa maximiza el área superficial y minimiza el espesor. p.9 ↗ | Select flask size and pre-freeze technique accordingly for efficient drying. | whole series |
| Si la temperatura eutéctica de la muestra es de -40 a -60 °C, el sistema debe tener refrigeración en cascada capaz de alcanzar un colector por debajo de -75 °C, o una trampa de hielo seco/disolvente entre el colector y la bomba. p.10 ↗ | Choose -84 °C or -105 °C models or add a secondary trap for low-eutectic samples. | whole series |
| Un sistema limpio y seco sin muestras debe alcanzar 0,133 mbar en 10 minutos y un vacío final de 0,040 mbar en 18 horas con la refrigeración en funcionamiento. p.53 ↗ | Use these benchmarks to judge whether vacuum performance is acceptable. | whole series |
| La bomba de vacío con salida bloqueada y un manómetro secundario debe alcanzar un vacío final inferior a 0,010 mbar (aproximadamente 10 micras). p.54 ↗ | If not achieved, the pump has likely failed and may need replacement or rebuild. | whole series |
| En condiciones sin carga, el colector debe alcanzar -50 °C, -84 °C o -105 °C (según el modelo) o menos en 30 minutos con la bomba de vacío en funcionamiento. p.58 ↗ | Failure to reach design temperature within 30 minutes indicates the refrigeration module is not functioning properly. | whole series |
| Operar la bomba de vacío a un nivel de vacío elevado (>10 mbar) puede expulsar aceite y causar daños. p.21 ↗ | Avoid prolonged pump operation at high inlet pressure; block the inlet when purging contaminants. | whole series |
| Cargas de refrigerante: 2,5L -50C R452A 185 g; 4,5L -50C R452A 210 g; 8L -50C R452A 390 g; 2,5L -84C R452A 190 g + R170 37 g; 4,5L -84C R452A 190 g + R170 39 g; 4,5L -105C R452A 410 g + R1150 55 g. p.7 ↗ | Use correct refrigerant type and charge for service; hydrocarbon refrigerants require authorized personnel. | specific models |
Faults & Troubleshooting
| Código / Síntoma | Possible Cause | Remedy | Note |
|---|---|---|---|
| Vacuum pump fails to operate p.53 ↗ | Electrical connections of the freeze dryer to the power source or of the vacuum pump to the freeze dryer; vacuum pump power switch may be off. | Check electrical connections of the freeze dryer to the power source and the vacuum pump to the freeze dryer; if the pump has a power switch, make sure it is turned on. | Chapter 7, Section I |
| Vacuum reading remains on HIGH p.53 ↗ | Vacuum START button not initiated on the display screen when the vacuum pump is plugged directly into a wall outlet for troubleshooting. | Initiate the vacuum START button on the display screen; otherwise the vacuum vent valve remains open. | Chapter 7, Section I |
| Vacuum is not adequate when the vacuum pump is operating p.53 ↗ | Cloudy or particulate-contaminated pump oil; incorrect oil level; loose vacuum hose connections. | Check oil clarity and replace if cloudy or particulate-laden (flush 5–10 minutes with clean oil as needed); check oil level; check vacuum hose connections from pump to freeze dryer and try running the unit. | Chapter 7, Section I, steps 1–3 |
| Inadequate vacuum reading when pump is deadheaded p.54 ↗ | Vacuum pump has most likely failed. | Replace or rebuild the vacuum pump. | Chapter 7, Section I, step 4 |
| Vacuum fluctuations when wiggling or rotating sample valves p.54 ↗ | Potential vacuum leak at the sample valve. | Remove valve and apply a thin coat of vacuum grease to the stem and outside sealing surface of the valve body, then reinstall; do not apply vacuum grease to sample valve gaskets that seal to the chamber wall; if still leaking, remove valve and stopper the hole with a rubber stopper. | Chapter 7, Section II, step 6 |
| Vacuum leak at bulkhead fittings (4.5L & 8L models) p.58 ↗ | Loose bulkhead fittings where collector coil penetrates the bottom of the chamber. | Remove insulation, place a wrench on the fitting inside the chamber and use a second wrench to turn the nut on the bottom of the chamber; if leak persists, loosen fittings and apply vacuum grease to the O-rings, reassemble and test. | Chapter 7, Section II, step 5 |
| Collector temperature does not reach design temperature within 30 minutes p.58 ↗ | Refrigeration module is not functioning properly. | Contact local laboratory supply dealer or Labconco; repairs should only be undertaken by a competent refrigeration technician or authorized Labconco service agency. | Chapter 7, Refrigeration Module Operation |