Induztr
Resumen técnico Visor de documentos Modelos relacionados

Rev j xpert nano enclosures user manual

Technical Reference Summary

Covered Models & Document Scope

Cubre la serie Labconco XPert® Nano Enclosure en anchos de 2', 3', 4', 5' y 6'. Los modelos de 2'/3'/4' utilizan una abertura de sash de 9.4" y un conducto de escape nominal de 6"; los modelos de 5'/6' utilizan una abertura de sash de 12" y un conducto de escape nominal de 10". Las opciones incluyen ionizador instalado en fábrica, Guardian Airflow Monitor o Guardian 1000 Digital Airflow Monitor, Canopy Exhaust Connection, sopladores remotos, compuertas de escape, filtros accesorios y estantes de servicios. Variantes eléctricas: 115 V con cable de alimentación y 230 V enviado sin enchufe.

Section-by-Section Technical Breakdown

pp. 7-9
Requisitos de sitio, soporte, vibración, temperatura y humedad

Define los requisitos previos para el sitio de instalación: nivelado, construcción sólida, alimentación eléctrica dedicada cercana y una bancada o soporte que minimice la vibración. Una deriva de temperatura de 1–2 °C es generalmente tolerable según los fabricantes de balanzas. La humedad debe mantenerse entre 45 y 60% para controlar la electricidad estática, y el recinto evita plásticos para reducir superficies aislantes.

  • Avoid tubular stands or mobile benches that can move when touched.
  • A bench rigidly mounted to floor or wall (not both) may be appropriate.
  • Building corners typically have less vibration than the center.
  • Do not place vibration-producing equipment such as shakers or pumps on the bench.
  • Marble slabs with dampening pads inside the enclosure are an effective low-cost vibration control.
  • Calibrate and verify the balance at least annually; best results when calibrated inside the enclosure at the desired face velocity.
  • Never install balances near radiators or hot plates; avoid direct sunlight on the bench.
  • Maintain humidity between 45 and 60%; a factory-installed ionizer is available to neutralize surface charges.
pp. 9
Requisitos de ubicación y corrientes de aire

El recinto debe colocarse para evitar corrientes cruzadas y turbulencias que alteren la contención y las lecturas de la balanza. Deben evitarse zonas de alto tránsito, difusores de HVAC, ventiladores, radiadores y puertas o ventanas que puedan abrirse. El dispositivo de desconexión principal debe permanecer accesible.

  • Avoid high-traffic areas where walking causes air disturbance.
  • Avoid overhead or wall HVAC diffusers, fans, radiators or other air-current-producing lab equipment.
  • Avoid locations next to doorways or windows that may be opened.
  • Do not position the unit so that the main disconnect device is difficult to operate.
pp. 10
Requisitos de escape y soplador

El impulsor motorizado integral aspira aire de la sala a través del filtro ULPA y expulsa el aire filtrado por la parte superior. El escape puede recircularse en el laboratorio o conducirse al exterior mediante la Canopy Exhaust Connection opcional y un soplador remoto. Las tablas indican el volumen de escape, la pérdida de presión estática, el ruido y la presión estática externa máxima para cada ancho a 60, 80 y 100 fpm.

  • 2' model at 60/80/100 fpm: 85/115/145 CFM; initial static pressure loss 0.35–0.41 / 0.48–0.57 / 0.62–0.72 in w.g.; noise 48–53 / 50–56 / 53–58 dB(A); max external static pressure 0.20 / 0.18 / 0.13 in w.g.
  • 3' model at 60/80/100 fpm: 130/175/220 CFM; static pressure loss 0.37–0.43 / 0.53–0.62 / 0.68–0.79 in w.g.; noise 48–53 / 53–57 / 58–61 dB(A); max external static pressure 0.15 / 0.11 / 0.08 in w.g.
  • 4' model at 60/80/100 fpm: 175/235/295 CFM; static pressure loss 0.40–0.46 / 0.57–0.66 / 0.76–0.87 in w.g.; noise 49–54 / 58–61 / 62–66 dB(A); max external static pressure 0.20 / 0.18 / 0.13 in w.g.
  • 5' model at 60/80/100 fpm: 290/385/480 CFM; static pressure loss 0.38–0.46 / 0.55–0.67 / 0.72–0.85 in w.g.; noise 52–56 / 58–63 / 63–67 dB(A); max external static pressure 0.22 / 0.20 / 0.15 in w.g.
  • 6' model at 60/80/100 fpm: 350/465/580 CFM; static pressure loss 0.46–0.56 / 0.67–0.81 / 0.87–1.03 in w.g.; noise 55–57 / 61–63 / 67–69 dB(A); max external static pressure 0.20 / 0.18 / 0.13 in w.g.
  • Weighing and handling nano materials is best done at lower flow rates of 60–70 fpm (0.31–0.36 m/s).
  • If connected directly to a house exhaust system, an adjustable damper or valve must be installed to control airflow, especially when one house system serves multiple filtered enclosures.
pp. 11, 18
Requisitos eléctricos y conexión

Debe haber receptáculos dúplex estándar cerca. El modelo de 115 V utiliza un cable de alimentación suministrado conectado a la entrada IEC en la parte posterior; el modelo de 230 V se envía sin enchufe y requiere un enchufe adecuado según los códigos locales. Todos los modelos consumen menos de 5 A. A 50 Hz, el caudal máximo del soplador se reduce en un 17%.

  • 115 V: connect supplied power cord to IEC electrical supply plug on back of enclosure.
  • 230 V: shipped without plug; install appropriate plug per local electrical specifications and codes.
  • All models use less than 5 amps.
  • At 50 Hz operation, blower maximum airflow is reduced by 17%.
  • All wiring should be performed by a licensed electrician and conform to local codes.
  • Do not use any detachable power cord that is not adequately rated for the unit.
pp. 12-14
Desembalaje e instalación del soporte/gabinete

Los recintos pesan de 173 a 443 lbs (78.47 a 200.94 kg) y deben moverse con una carretilla elevadora mecánica, un gato de piso o una plataforma baja bajo el patín de envío; no inclinar sobre una carretilla de mano ni levantar por el air foil frontal. La superficie superior del soporte base se ajusta de 27.5 a 34.50 pulgadas (698 a 876 mm) en incrementos de 1 pulgada (25 mm). La superficie de trabajo integral de acero inoxidable se monta al soporte con cuatro pernos de 1/4"-20 x 2.5".

  • Enclosure weight range: 173 to 443 lbs (78.47 to 200.94 kg).
  • Do not move the enclosure by tilting it onto a hand truck.
  • Do not lift by the front air foil.
  • Base stand height adjustable 27.5 to 34.50 inches (698 to 876 mm) in 1-inch (25 mm) increments.
  • Leg extensions attach with 5/16"-18 x 2-1/4 inch (57 mm) bolts, flatwasher, lockwasher and acorn nut; select the same height hole for each leg.
  • Work surface mounts with four 1/4"-20 x 2.5 inch (63 mm) hex head bolts, nuts and washers; front edge flush with stand front edge.
  • Use a carpenter level to adjust leveling feet in both planes.
pp. 15-17
Conexión al sistema de escape (opcional)

Los modelos de 2', 3' y 4' aceptan conducto nominal de 6" (6.06" DI) y los modelos de 5' y 6' aceptan conducto nominal de 10" (10.06" DI). En los tamaños 2'/3'/4' la conexión de escape se envía sin instalar en la parte superior y se fija con los tornillos suministrados. El peso de la red de conductos debe soportarse independientemente de la superestructura del recinto.

  • 2', 3', 4' models: 6" nominal exhaust duct, 6.06" ID.
  • 5', 6' models: 10" nominal exhaust duct, 10.06" ID.
  • Exhaust connection on 2'/3'/4' ships uninstalled on top; fasten with screws provided.
  • The weight of the exhaust ductwork system must be supported independently of the enclosure superstructure or damage may occur.
  • Exhaust system should be installed by a qualified HVAC contractor.
  • Selected exhaust duct material should match the enclosure, procedures and chemical applications.
pp. 18-19
Ajuste de la velocidad frontal con el control de velocidad

El control de velocidad detrás del panel frontal ajusta la velocidad frontal de 60 a 100 fpm. La velocidad frontal promedio se mide con un anemómetro en dos filas a través de la abertura del sash: lecturas a 6" de los extremos y cada 12", primera fila a 3" hacia abajo desde el foil del sash superior y segunda fila a 3" hacia arriba desde la superficie de trabajo. Las pruebas de flujo de aire de Labconco según ASHRAE 110-1995 alcanzaron una calificación de fabricación inferior a 0.05 ppm a 4 lpm.

  • Face velocity adjustable from 60 to 100 fpm via speed control behind front panel.
  • Containment is maximized within this range; lowest permissible velocity gives least turbulent, quietest operation.
  • Average face velocity readings: two rows, 6" from ends, evenly spaced every 12"; first row 3" down from upper sash foil, second row 3" up from work surface.
  • As-manufactured ASHRAE 110-1995 rating: less than 0.05 ppm at 4 lpm.
  • Face velocity profiles and smoke testing should be performed frequently per the organization's quality system.
pp. 20-24
Características de alto rendimiento

Describe los elementos de diseño aerodinámico: air foil Clean-Sweep, foil del sash superior, suministro de aire de dilución superior, deflector perforado trasero zonificado, air foils de entrada lateral, sash de vidrio de seguridad, puertos de servicios, plenum de presión negativa, impulsor motorizado aislado de vibraciones, control de velocidad, manómetro de presión del sistema de filtros, puerto de acceso al filtro ULPA, panel de control, filtro ULPA, collarín de escape opcional, conexión de escape tipo canopy, ionizador y estantes de servicios.

  • Upper dilution air supply introduces 5 to 7 percent of required air volume through the upper dilution air supply.
  • Zoned rear perforated baffle has three zones with increasingly more open area at the bottom to form laminar airflow.
  • Safety glass sash has a wiping seal and spring-loaded latch; 5' and 6' units use a gas spring assist instead of the latch.
  • ULPA filter rated to remove 99.999% of all particles 0.12 micron in size.
  • Plenum and ULPA filter are jacketed by negative pressure; leaks are recaptured and refiltered.
  • True bag-in/bag-out ULPA filter disposal system protects worker from hazardous powders and particulates.
  • Optional ionizer cannot be installed after manufacture.
  • Filter system pressure gauge indicates total system pressure across filter and pressurized plenum to help predict filter loading.
pp. 27-28
Procedimientos rutinarios de trabajo diario

Cubre la planificación, el arranque, la carga, las técnicas de trabajo, la purga final, la descarga y el apagado. Deje que el recinto funcione sin obstrucciones durante 1 minuto al arrancar y después de cargar; tras el trabajo, deje de 2 a 3 minutos de purga sin perturbaciones antes de apagar el soplador.

  • Turn on exhaust system and light; only raise sash for loading and cleaning.
  • Check baffle air slots for obstructions.
  • Allow enclosure to operate unobstructed for 1 minute before work.
  • After loading, wait one minute to purge airborne contaminants.
  • Upon completion, allow enclosure to operate for two to three minutes undisturbed before shutting down blower.
  • Surface decontaminate objects in contact with contaminated material before removal; cover open trays, weigh vessels or containers before removal.
pp. 28
Aplicaciones, idoneidad y directrices del filtro ULPA

El filtro ULPA es adecuado para pesar y manipular polvos, partículas no volátiles, polvos peligrosos y materiales biopeligrosos. Proporciona protección al personal y al medio ambiente, pero no protección del producto frente a la contaminación ambiental. Los gases o vapores requieren ventilación al exterior. La superficie del filtro es frágil y no debe tocarse ni perforarse.

  • Suitable for weighing and handling of powders and release of nonvolatile particulates.
  • Provides personal and environmental protection from particulate matter, hazardous powders and biohazardous materials.
  • Not for operations requiring sample protection from environmental contamination.
  • ULPA filters are only effective for entrapment of particulate matter; gases or vapors require outside ventilation.
  • If a ULPA filter is suspected damaged, do not use the enclosure; contact a certification agency or Labconco.
  • For powders and particulates follow the ULPA Filter Bag-In/Bag-Out procedure in Chapter 6; for biohazardous materials follow the Decontamination Procedure.
pp. 25, 43
Ionizador opcional

El ionizador instalado en fábrica controla la carga estática en las superficies dentro del recinto. Su descarga se ubica en la cara frontal de la superficie de trabajo, protegida de contaminantes y de la limpieza. Los emisores tienen una vida finita y pueden requerir reemplazo.

  • Ionizer floods the work area with positive and negative ions to neutralize static charges on non-conductive items.
  • Discharge located at the front face of the work surface.
  • Ionizer cannot be installed after manufacture.
  • Emitters have a finite life and may require replacement.
pp. 27-44
Programa de mantenimiento rutinario

Proporciona un programa para el mantenimiento rutinario, incluida la descontaminación, la determinación de cuándo reemplazar los filtros ULPA, la instalación de filtros bag-in/bag-out, las pruebas de fuga del filtro, el ajuste de la velocidad frontal de entrada y la calibración y operación de los monitores de flujo de aire.

  • Routine maintenance schedule covers decontamination, filter replacement determination, bag-in/bag-out filter installation, filter leak test, face velocity setting and airflow monitor calibration.
  • Initial certification and re-certification are required.
  • Fluorescent and LED light replacement, motorized impeller replacement, speed control replacement, ionizer maintenance and trace odor carbon filter installation are covered.
pp. 28-31
Reemplazo del filtro ULPA, bag-in/bag-out y prueba de fuga

Describe la determinación de cuándo reemplazar los filtros ULPA, la instalación de un nuevo filtro ULPA mediante el procedimiento bag-in/bag-out y la prueba de fuga del filtro. El perno de sujeción del filtro sella uniformemente el filtro al marco. Los filtros ULPA de escape se desechan como residuos peligrosos utilizando la bolsa de desecho.

  • Replace ULPA filter when face velocity falls below acceptable limits established by Safety Officer.
  • Use true bag-in/bag-out procedure for harmful powders and particulates.
  • Filter clamping bolt evenly seals filter to enclosure frame.
  • Exhaust ULPA filters are disposed as hazardous waste; user is responsible for recording material and disposing properly.
  • Filter leak test is part of maintenance.
pp. 33-40
Calibrar y operar los monitores de flujo de aire

Cubre el Guardian Digital 1000 Airflow Monitor y el Guardian Airflow Monitor, incluida la programación de la alarma digital Guardian 1000. El Guardian 1000 muestra la velocidad frontal, proporciona salida RS232, modo de reducción nocturna y puertos de relé auxiliares. Los pasos de calibración se describen en el Capítulo 6 o en el Manual del Digital 1000 Monitor suministrado.

  • Guardian 1000 Digital Airflow Monitor displays face velocity value, provides RS232 output, night setback mode and several auxiliary relay ports.
  • Guardian Airflow Monitor continuously monitors airflow with audio/visual alarm for low airflow.
  • Programming the Guardian 1000 Digital Alarm is covered.
  • Calibration steps are in Chapter 6 or the supplied Digital 1000 Monitor Manual.
pp. 40-44
Mantenimiento de luz, impulsor motorizado, control de velocidad e ionizador

Cubre el reemplazo de luz fluorescente y LED, el reemplazo del impulsor motorizado, el reemplazo del control de velocidad, el mantenimiento del ionizador opcional y la instalación del filtro de carbón para olores traza.

  • Fluorescent light replacement and LED light replacement procedures.
  • Motorized impeller replacement procedure.
  • Speed control replacement procedure.
  • Maintenance on the optional ionizer.
  • Trace odor carbon filter installation.
pp. 45-48
Accesorios del Nano Enclosure

Enumera las opciones de accesorios: Guardian Airflow Monitors, Canopy Exhaust Connection, sopladores remotos, compuertas de escape y filtros accesorios. La Canopy Exhaust Connection incluye un adaptador de transición de escape de acero recubierto de epoxi para conducto nominal de 6" en tamaños 2'/3'/4' y conducto nominal de 10" en tamaños 5'/6'.

  • Guardian Airflow Monitors available as accessories.
  • Canopy Exhaust Connection includes epoxy-coated steel exhaust transition adapter.
  • 2', 3', 4' sizes use 6" nominal duct; 5', 6' sizes use 10" nominal duct.
  • Remote blowers and exhaust dampers available.
  • Accessory filters available.
pp. 53-64
Piezas de repuesto, dimensiones y especificaciones

El Apéndice A enumera las piezas de repuesto, el Apéndice B proporciona las dimensiones de todos los modelos, el Apéndice C proporciona las especificaciones eléctricas y ambientales, y el Apéndice D es una tabla rápida.

  • Appendix A: Replacement Parts.
  • Appendix B: Dimensions for different models.
  • Appendix C: Specifications for electrical and environmental conditions.
  • Appendix D: Quick Chart.

Key Integration, Operating & Safety Requirements

Specification / Condition Engineering Implication Aplica a
Filtro ULPA con una eficiencia nominal de al menos 99.999% para partículas de 0.12 micrones. p.5 ↗ Suitable for containment of hazardous powders and biohazardous particulates; not for gases or vapors. whole series
Velocidad frontal ajustable de 60 a 100 fpm mediante el control de velocidad detrás del panel frontal. p.18 ↗ Set within this range for containment; lowest permissible velocity gives least turbulent, quietest operation. whole series
Para procedimientos de pesaje, la velocidad frontal debe ser de 60–100 fpm; para procedimientos biopeligrosos, de 75–105 fpm. p.54 ↗ Select face velocity according to application; verify with anemometer. whole series
El pesaje y la manipulación de nanomateriales se realizan mejor a caudales más bajos de 60–70 fpm (0.31–0.36 m/s). p.10 ↗ Use lower face velocity for nanoparticle work to optimize containment. whole series
Los modelos de 2', 3', 4' aceptan conducto de escape nominal de 6" (6.06" DI); los modelos de 5', 6' aceptan conducto nominal de 10" (10.06" DI). p.15 ↗ Ductwork and canopy exhaust connection must match model width. 2'/3'/4' vs 5'/6' models
Modelo de 2' a 60 fpm: 85 CFM, pérdida de presión estática inicial 0.35–0.41 in w.g., ruido 48–53 dB(A), presión estática externa máxima 0.20 in w.g. p.10 ↗ Use for blower sizing and exhaust system design. 2' model
Modelo de 6' a 100 fpm: 580 CFM, pérdida de presión estática inicial 0.87–1.03 in w.g., ruido 67–69 dB(A), presión estática externa máxima 0.13 in w.g. p.10 ↗ Highest airflow and pressure loss of the series; blower must be sized accordingly. 6' model
Todos los modelos utilizan menos de 5 amperios. p.18 ↗ Standard duplex receptacle circuit is adequate; verify local codes. whole series
A operación de 50 Hz, el caudal máximo del soplador se reduce en un 17%. p.18 ↗ Account for reduced airflow when sizing blower and setting face velocity in 50 Hz regions. whole series
Rango de peso del recinto: 173 a 443 lbs (78.47 a 200.94 kg). p.12 ↗ Use mechanical lift truck, floor jack or low dolly under shipping skid; do not tilt onto hand truck or lift by front air foil. whole series
Superficie superior del soporte base ajustable de 27.5 a 34.50 pulgadas (698 a 876 mm) en incrementos de 1 pulgada (25 mm). p.14 ↗ Select optimum working height; use same height hole for each leg. models with base stand
La superficie de trabajo se monta con cuatro pernos hexagonales de 1/4"-20 x 2.5 pulgadas (63 mm), tuercas y arandelas; las extensiones de patas utilizan pernos de 5/16"-18 x 2-1/4 pulgadas (57 mm). p.14 ↗ Use specified hardware for assembly; tighten after all four bolts started. models with base stand
El suministro de aire de dilución superior introduce de 5 a 7 por ciento del volumen de aire requerido. p.23 ↗ Part of total airflow; account for when measuring face velocity. whole series
Medición de la velocidad frontal promedio: dos filas, lecturas a 6" de los extremos y cada 12", primera fila a 3" hacia abajo desde el foil del sash superior, segunda fila a 3" hacia arriba desde la superficie de trabajo. p.18 ↗ Standardized method for certifying face velocity. whole series
Calificación de fabricación ASHRAE 110-1995: inferior a 0.05 ppm a 4 lpm. p.18 ↗ Baseline containment performance; field testing available through Labconco certified contractor. whole series
Mantener la humedad entre 45 y 60% para controlar la electricidad estática. p.8 ↗ Static charges can cause weighing errors and particulate attraction; ionizer available as factory option. whole series
Una deriva de temperatura de 1–2 °C es generalmente tolerable según los fabricantes de balanzas. p.8 ↗ Avoid heating sources and direct sunlight; validate through Operational Qualification protocol. whole series
Deje el soplador encendido al menos un minuto después del trabajo; permita de 2 a 3 minutos de purga sin perturbaciones antes del apagado. p.26 ↗ Ensures airborne contaminants are purged before blower is turned off. whole series
El recinto debe recertificarse siempre que se realice mantenimiento o al menos anualmente a partir de entonces. p.25 ↗ Maintain certification schedule for continued safe operation. whole series
Si se conecta directamente a un sistema de escape del edificio, debe instalarse una compuerta o válvula ajustable para controlar el flujo de aire. p.10 ↗ Required especially when one house system serves multiple filtered enclosures. models with house exhaust connection

Faults & Troubleshooting

Código / Síntoma Possible Cause Remedy Note
Contaminants outside of enclosure. p.54 ↗ Improper user techniques for the enclosure. See "Certifying the Enclosure" Chapter 3 and "Safety Precautions" Chapter 4 sections in the manual. (Ref. Appendix D). Chapter 8
Contaminants outside of enclosure. p.54 ↗ Restriction of the baffle air slots or blockage of the exhaust outlet. Remove obstruction to ensure that all air slots and the exhaust outlet are unobstructed. Chapter 8
Contaminants outside of enclosure. p.54 ↗ External factors are disrupting the enclosure airflow patterns or acting as a source of contamination. See "Location Requirements" Chapter 2, "Certifying the Enclosure" Chapter 3, and "Safety Precautions" Chapter 4 sections of this manual. (Ref. Appendix D). Chapter 8
Contaminants outside of enclosure. p.54 ↗ Enclosure has improper face velocity. Have enclosure certified and check exhaust system. Check filters for loading. Adjust enclosure speed control. Enclosure should have an average face velocity of 60-100 fpm for weighing procedures and 75-105 fpm for biohazardous procedures. Chapter 8
Blower won't operate. p.54 ↗ Unit not plugged into outlet. Plug the enclosure into appropriate electrical service. Chapter 8
Blower won't operate. p.54 ↗ Circuit breaker(s) or Ground Fault Interrupter. Reset circuit breaker. Chapter 8
Blower won't operate. p.54 ↗ Blower wiring is disconnected. Inspect blower wiring. Chapter 8
Blower won't operate. p.54 ↗ Blower switch is defective. Replace switch. Chapter 8
Blower won't operate. p.54 ↗ Motorized impeller or blower is defective. Replace motorized impeller or blower. See Chapter 6. Chapter 8
Low face velocity or poor containment of contaminants. p.54 ↗ Enclosure sash not closed. Close sash to the lowest position. Chapter 8
Low face velocity or poor containment of contaminants. p.54 ↗ ULPA filter clogged. Replace ULPA filter or increase speed. Chapter 8
Low face velocity or poor containment of contaminants. p.54 ↗ Carbon filter loaded with chemicals. Replace carbon filter. Chapter 8
Blower and lights won't operate. p.54 ↗ Unit not plugged into outlet. Plug enclosure into appropriate electrical service. Chapter 8
Blower and lights won't operate. p.54 ↗ Circuit breaker(s) tripped. Reset or replace circuit breaker. Chapter 8
Lights do not work. p.55 ↗ Lamp not installed properly. Inspect lamp installation. Chapter 8
Lights do not work. p.55 ↗ Lamp wiring disconnected. Inspect lamp wiring. Chapter 8
Lights do not work. p.55 ↗ Defective lamp. Replace lamp. Chapter 8
Lights do not work. p.55 ↗ Light switch is defective. Replace light switch. Chapter 8
Lights do not work. p.55 ↗ Defective electronic ballast. Replace ballast. Chapter 8
Airflow monitor malfunction. No power. No lights. No display. p.55 ↗ Power cable to circuit board is disconnected and needs to be connected. Sensor cable needs to be connected. Power supply is not plugged into proper voltage; plug in power supply. Verify that all airflow monitor interface cables are connected. Check fuses on enclosure. Connect power cable to circuit board; connect sensor cable; plug power supply into proper voltage; verify all airflow monitor interface cables are connected; check fuses on enclosure. Chapter 8
No audible alarm. p.55 ↗ Alarm has been temporarily silenced using "SILENCE ALARM" or "enter" buttons. Check alarm status; refer to Chapter 6 or Digital 1000 Monitor Manual. Chapter 8
Wrong alarm set point. p.55 ↗ Airflow monitor was not properly adjusted. Repeat calibration steps outlined in this manual in Chapter 6 or in the supplied Digital 1000 Monitor Manual. Chapter 8
Constant audible alarm. p.55 ↗ Airflow monitor calibration or airflow issue. Check airflow and calibration of airflow monitor. See Chapter 6. Chapter 8
Continuous alarm. p.55 ↗ Face velocity of the enclosure may have changed; airflow of the system may have changed; ULPA filter may have become loaded. Check the face velocity of the enclosure. If incorrect, adjust the speed control to increase face velocity. If face velocity is correct, calibrate the airflow monitor outlined in this manual in Chapter 6. Chapter 8
Monitor alarms; air way to airflow monitor sensor is blocked by insects, dust or debris. p.55 ↗ Airway to airflow monitor sensor is blocked by insects, dust or debris. Lightly clean the airway with clean air. Be careful not to touch sensitive electrical components. Chapter 8
Audible disable will not stay operational. p.55 ↗ An alarm condition must be continuously present before the audible alarm can be silenced. If flow conditions fluctuate near the alarm set point, the airflow monitor will automatically reset it. Action should be taken to bring the enclosure airflow into proper operating parameters or adjust the alarm set point lower. Chapter 8