Instruction Manual - Nexera UC Piping Kit -
Technical Reference Summary
Covered Models & Document Scope
Kits de tuberías del sistema Nexera UC (documento 228-92325D). Abarca todas las variantes de kits de tuberías identificadas por símbolo: B (Basic, 228-61492-41), M (MS, 228-61493-41), O (Online, 228-61494-41), E (SFE, 228-61496-41), C (Column Switching 6, 228-61105-43 para FCV-34AH / -45 para FCV-0607), P (Column Switching +6, 228-61105-44 para FCV-34AH / -46 para FCV-0607), H (High pressure gas, 228-61497-41), m (MS para I.D. 0.1 mm, 228-63782-41), c (Column Switching 6 para I.D. 0.1 mm, 228-63783-41 para FCV-0607 / -43 para FCV-34AH), p (Column Switching +6 para I.D. 0.1 mm, 228-63783-42 para FCV-0607 / -44 para FCV-34AH), F (Fraction Collector Modification Kit for Prep SFC, 228-75753-42), f (Fraction Collector Modification Kit for Analytical SFC, 228-79729-41), A (Analytical Fraction MS, 228-68817-41), L (LC/SFC Switching, 228-62767-41), D (Direct/Loop Injection Switching, 228-75296-42 para FCV-32AH / -43 para FCV-0206).
Section-by-Section Technical Breakdown
El manual asigna cada símbolo de kit de tuberías a una configuración específica del sistema Nexera UC. Los kits de I.D. 0.1 mm son kits adicionales que sustituyen la tubería estándar de I.D. 0.3 mm para reducir el volumen muerto del sistema. El símbolo de la tabla corresponde al símbolo del diagrama de tuberías donde se utiliza cada kit.
- B is the common basic piping kit for every system.
- M is required when using MS; O is for the Online SFE-SFC system; E is for SFE.
- C and P are for 6- or 12-column switching and are ordered by valve type (FCV-34AH vs FCV-0607).
- m, c and p are I.D. 0.1 mm additional kits that replace standard I.D. 0.3 mm piping to reduce dead volume.
- F and f modify the FRC-40 fraction collector for Prep SFC and Analytical SFC respectively.
- A is used for MS-triggered or ELSD-triggered fractionation in the Analytical Fraction system.
- L and D kits have their own attached instruction manuals.
Enumera las 17 líneas del kit de tuberías Basic con números de pieza, cantidades y ubicaciones de instalación. El kit incluye tubos de SUS y ETFE, férulas, tuercas macho, acoplamientos, etiquetas, bandas de cableado y un tubo de puerto de inyección en bucle para SIL-40.
- B1 SUS Tubing (1.0x100) 228-61552-41 connects line filter to ghost trap.
- B2 SUS Tubing (1.0x2000) 228-61552-42 connects ghost trap to CO2 pump.
- B3 SUS Sleeve Tubing (0.3x1200) 228-53184-41, qty 2, for modifier pump–mixer and CO2 pump–mixer.
- B4 SUS Sleeve Tubing (0.3x700) 228-53184-93 for T-joint–column; also mixer–high pressure valve on Chiral Screening System.
- B5 SUS Tubing (0.3x175) 228-57292-45 for BPR (1)–coupling.
- B6 ETFE Tubing (1.6x1.0x2000) 228-18495-03 for drain tubing (Chiral Screening System only).
- B7 Ferrule 1.6F 316L 228-16000-10 qty 13; B8 Male Nut 1.6MN 228-16001 qty 11; B9 Male Nut 1.6MN,W6 228-16001-03 qty 2; B10 Male Nut 1.6MN PEEK 228-35403 qty 2; B11 Coupling 1.6C-0.4 316L 228-16004-13 qty 2.
- B12 Label, Right Panel 228-61147 qty 11; B13 Wiring Band IT18FL-B 072-60355-07 qty 70; B14 Label, Identification Tag 228-61513 qty 1.
- B15 SUS Sleeve Tubing (0.3x300) 228-53184-92 for Cell Out–BPR (1).
- B16 Injection port pipe, I.D. Φ0.17 228-64106-49 for SIL-40 Loop Injection.
- B17 Male Nut 1.6MN-L 228-16001-01 for BPR (1) IN.
Enumera las 8 líneas del kit de tuberías MS. Proporciona la línea de bomba de reposición a unión en T, el tubo de conexión al MS, una válvula de retención que sustituye el filtro de línea de la bomba de reposición, y la unión en T y sus racores.
- M1 SUS Sleeve Tubing (0.1x200) 228-53184-45 qty 2 for column–T-joint and T-joint–BPR (1).
- M2 SUS Sleeve Tubing (0.3x1200) 228-53184-41 for makeup pump–T-joint.
- M3 PEEK TUBE 5999 (0.13x400) 228-32999-01 or 016-42903-01 qty 1 for MS connection.
- M4 Check Valve 228-53334-96 replaces the line filter of the makeup pump.
- M5 T-joint 0.4 228-16008-11 qty 1.
- M6 Ferrule 1.6F 316L 228-16000-10 qty 6; M7 Male Nut 1.6MN 228-16001 qty 5; M8 Male Nut 1.6MN-L 228-16001-01 qty 1.
Enumera las 11 líneas del kit de tuberías Online SFE-SFC. Incluye las líneas SIL HPV–unión en T y unión en T–BPR (2), una unión en T, racores, tubo de drenaje de ETFE y tuercas macho de PEEK.
- O1 SUS Sleeve Tubing (0.3x300) 228-53184-92 for SIL HPV–T-joint.
- O2 SUS Sleeve Tubing (0.3x700) 228-53184-93 for T-joint–BPR (2).
- O3 T-joint 0.4 228-16008-11 qty 1.
- O4 Ferrule 1.6F 316L 228-16000-10 qty 5; O5 Male Nut 1.6MN 228-16001 qty 3; O6 Male Nut 1.6MN-L 228-16001-01 qty 1; O7 Male Nut 1.6MN,W6 228-16001-03 qty 1.
- O8 SUS Tubing ID0.3xL175 228-57292-45 for BPR (2)–coupling.
- O9 Coupling 1.6C-0.4 316L 228-16004-13 qty 1.
- O10 ETFE Tubing OD1.6xID1.0xL2000 228-18495-03 qty 1.
- O11 Male Nut 1.6MN PEEK 228-35403 qty 2.
Enumera las 6 líneas del kit de tuberías SFE. Proporciona tubos mezclador–SFE y SFE–SIL, racores, y un amortiguador más un tornillo de fijación M4x8 para instalar el mezclador en el sistema de pretratamiento SFE.
- E1 SUS Sleeve Tubing (0.3x1200) 228-53184-41 qty 2 for mixer–SFE and SFE–SIL.
- E2 Ferrule 1.6F 316L 228-16000-10 qty 4; E3 Male Nut 1.6MN 228-16001 qty 2; E4 Male Nut 1.6MN,W6 228-16001-03 qty 3.
- E5 Cushion qty 1 is inserted between the mixer mounting plate and the side of the pump as a protective material.
- E6 Bind Screw M4x8 qty 1 fastens one point on the side of the pump for mixer installation.
Enumera los componentes para conmutación de 6 o 12 columnas. La variante -43 es para FCV-34AH y la variante -45 es para FCV-0607; las cantidades difieren entre variantes. El kit incluye el MSS2 CD ASSY, colector, abrazaderas de columna, etiquetas de identificación por color y tapones.
- MSS2 CD ASSY 228-64206-41 qty 1 is used to install Method Scouting System.
- C1 SUS Sleeve Tubing (0.3x300) 228-53184-92 qty 12 for 6 positions FCV–column (6 pc) and column–manifold (6 pc).
- C2 Ferrule 1.6F 316L 228-16000-10 qty 18 (-43) or 24 (-45); C3 Male Nut 1.6MN 228-16001 qty 18; C6 Male Nut 1.6MN,W6 228-16001-03 qty 6 only for -45.
- C8 Manifold ASSY,6IN-1OUT 228-54450-91 qty 1.
- C9 Color Identification Tag Column ASSY 228-54728-92 qty 1; C10 Color Identification Tag MP ASSY 228-54728-93 qty 1.
- C11 Column Clamp ASSY B5 228-15617-91 qty 4 for -43; Column Clamp 228-72586 qty 4 for -45.
- C16 Plug 228-16006-10 qty 6.
Enumera los componentes para conmutación de 12 columnas. La variante -44 es para FCV-34AH y la -46 es para FCV-0607; las cantidades difieren. El kit añade un segundo colector, una unión en T, tubos adicionales y etiquetas de color.
- P1 SUS Sleeve Tubing (0.3x300) 228-53184-92 qty 15 for 2 positions FCV–6 positions FCV (1), 6 positions FCV (2)–column (6 pc), column–manifold (6 pc), manifold (1)–T-joint and manifold (2)–T-joint.
- P3 T-joint 0.4 228-16008-11 qty 1.
- P4 Ferrule 1.6F 316L 228-16000-10 qty 26 (-44) or 34 (-46); P5 Male Nut 1.6MN 228-16001 qty 23 (-44) or 24 (-46); P6 Male Nut 1.6MN,W6 228-16001-03 qty 2 (-44) or 10 (-46).
- P7 Coupling 1.6C-0.4 316L 228-16004-13 qty 1; P8 Manifold ASSY,6IN-1OUT 228-54450-91 qty 1.
- P9 Color Identification Tag Column ASSY 228-54728-92 qty 1; P10 Color Identification Tag Column ASSY 228-54728-94 qty 1; P11 Color Identification Tag MP ASSY 228-54728-93 qty 1.
- P12 Column Clamp ASSY B5 228-15617-91 qty 4 for -44; Column Clamp 228-72586 qty 4 for -46.
- P13 Male Nut 1.6MN-L 228-16001-01 qty 1; P14 SUS Sleeve Tubing (0.1x200) 228-53184-45 qty 1 for SIL–2 positions FCV; P15 SUS Sleeve Tubing (0.3x700) 228-53184-93 qty 1 for 2 positions FCV–6 positions FCV (2); P16 Plug 228-16006-10 qty 6.
Enumera las 6 líneas del kit de tuberías para gas de alta presión. Incluye una unión de cilindro, juntas de PTFE, un filtro de línea, una trampa fantasma para atrapar objetos extraños de los cilindros, una válvula de retención y un mezclador MR.
- H1 Cylinder Joint 228-61086 qty 1 for connection to cylinder.
- H2 Gasket (PTFE) 228-61087-10 qty 3.
- H3 Line Filter 228-58173-42 qty 1.
- H4 Ghost trap 228-61088-41 qty 1 used to trap foreign objects from cylinders.
- H5 Check valve 228-53334-96 qty 1; replace it with a line filter.
- H6 MR mixer, 180UL SFC 228-61089-41 qty 1.
Enumera las 6 líneas del kit adicional de tuberías MS de I.D. 0.1 mm. Proporciona tubos BPR IN y BPR OUT más racores para la trayectoria de flujo del MS de volumen muerto reducido.
- m1 SUS Tubing, BPR IN 228-57271-41 qty 1 for BPR (1).
- m2 SUS Tubing, BPR OUT 228-57292-41 qty 1 for BPR (1)–coupling.
- m3 Ferrule 1.6F 316L 228-16000-10 qty 3; m4 Male Nut 1.6MN 228-16001 qty 2; m5 Male Nut 1.6MN-L 228-16001-01 qty 1; m6 Male Nut 1.6MN PEEK 228-35403 qty 1.
Enumera los componentes del kit adicional de I.D. 0.1 mm para conmutación de 6 o 12 columnas. La variante -41 es para FCV-0607 y la variante -43 es para FCV-34AH; la variante -43 añade férulas y casquillos para conexiones a FCV-34AH.
- c1 SUS Sleeve Tubing (0.1x200) 228-53137-45 qty 12 for 6 positions FCV–column (6 pc) and column–manifold (6 pc).
- c3 Ferrule 1.6F 316L 228-16000-10 qty 24; c4 Male Nut 1.6MN 228-16001 qty 18; c5 Male Nut 1.6MN,W6 228-16001-03 qty 6.
- c6 FERRULE, 7010-010 670-11412-04 qty 7 only for -43, used for FCV-34AH piping connection.
- c7 BUSH, 7010-011 670-11412-02 qty 6 only for -43; c8 BUSH, 7010-062 670-11412-03 qty 1 only for -43.
Enumera los componentes del kit adicional de I.D. 0.1 mm para conmutación de 12 columnas. La variante -42 es para FCV-0607 y la variante -44 es para FCV-34AH; la variante -44 añade férulas y casquillos para conexiones a FCV-34AH.
- p1 SUS Sleeve Tubing (0.1x200) 228-53137-45 qty 15 for 2 positions FCV–6 positions FCV (1), 6 positions FCV (2)–column (6 pc), column–manifold (2) (6 pc), manifold (1)–T-joint and manifold (2)–T-joint.
- p2 SUS Sleeve Tubing (0.1x600) 228-53137-94 qty 1 for 2 positions FCV–6 positions FCV (2).
- p3 Ferrule 1.6F 316L 228-16000-10 qty 32; p4 Male Nut 1.6MN 228-16001 qty 22; p5 Male Nut 1.6MN,W6 228-16001-03 qty 10.
- p6 FERRULE, 7010-010 670-11412-04 qty 7 only for -44, used for FCV-34AH piping connection.
- p7 BUSH, 7010-011 670-11412-02 qty 6 only for -44; p8 BUSH, 7010-062 670-11412-03 qty 1 only for -44.
Enumera los componentes que modifican el FRC-40 para Prep SFC. Incluye una válvula de retención con orientación de flujo definida, una unión de filtro de línea, tubo de FCV a GLS, tapones de cierre y racores. Los elementos X1–X3 no están incluidos en el kit y deben adquirirse por separado.
- F2 CV,OUT-30ADSF 228-45705-41: valve joint side is upstream and check valve side is downstream.
- F3 SUS Joint, for Line Filter, Nexera UC 228-50707-01 qty 1.
- F4 SUS Sleeve Tubing (0.1x600) 228-53137-96 for T-joint–FCV (L), port 2.
- F5 PIPE (1.6x1.0x300 ORANGE) 228-68910-61 qty 2 for T-joint–FCV (R), port 1; only 1 is used, keep the other as spare.
- F6 PEEK TUBE / SUS TUBE 0.5 mm I.D. 228-77523-42 (included in GLS kit) for FCV (R), port 2–GLS; F7 ETFE TUBE 0.5 mm I.D. for FCV (L), port 1–GLS.
- F8 PLUG 228-16006-10 qty 3: use stop plugs on port 3 of FCV (R) and ports 3 and 6 of FCV (L); if not closed, leakage may occur depending on valve position.
- F9 MALE NUT 1.6MN 228-16001 qty 6; F10 FERRULE 1.6F 316L 228-16000-10 qty 6.
- X1 SUS Sleeve Tubing (0.3x300) 228-53137-42 qty 2, X2 SUS Sleeve Tubing (0.3x1200) 228-53184-41 qty 1 and X3 FEMALE,1.6FT316L-0.4 228-16008-11 qty 1 are not included in this kit; use additionally purchased piping.
Enumera los componentes que modifican el FRC-40 para Analytical SFC. Incluye tubo de bomba de reposición, una válvula de retención con orientación de flujo definida, una unión de filtro de línea, tubo de PEEK SIL, tubo de ETFE para flujo principal y de enjuague, y tapones de cierre.
- f1 SUS Tubing (1.6x0.3x2000) 228-50579-91 for FRC makeup pump–T-joint.
- f4 CV,OUT-30ADSF 228-45705-41: valve joint side is upstream and check valve side is downstream.
- f5 SUS Joint, for Line Filter, Nexera UC 228-50707-01 qty 1.
- f6 PEEK SIL TUBE (0.05x100) 225-42910-30 for T-joint–coupling.
- f7 SUS Sleeve Tubing (0.3x300) 228-53137-42 qty 3 for T-joint–valve joint, check valve–T-joint and T-joint–FCV port 2.
- f8 ETFE TUBE 0.3 mm I.D. 228-79342-43 (included in GLS kit) for T-joint–solenoid valve (main flow); f9 ETFE TUBE 0.3 mm I.D. with 'Rinse' tag for FCV port 1–GLS (rinse flow); f10 ETFE TUBE 1.0 mm I.D. for solenoid valve–drain.
- f11 PLUG 228-16006-10 qty 1: use stop plug on port 3 of FCV; if the valve is not closed, leakage may occur.
- f12 MALE NUT 1.6MN 228-16001 qty 10; f13 FERRULE 1.6F 316L 228-16000-10 qty 10.
Enumera los componentes para fraccionamiento disparado por MS o por ELSD en el sistema Analytical Fraction. Incluye tubo de retardo para ajuste de capacidad, tubo de PEEK SIL cortado a medida para conexión al MS, una válvula de retención para prevención de reflujo y tubo de drenaje.
- A1 SUS Sleeve Tubing (0.3x300) 228-53137-42, I.D. 0.3 mm × 300 mm.
- A2 PEEK SIL TUBE 018-30510-51, I.D. 0.025 mm × 500 mm; 2 tubes included but only 1 is used, keep the other as spare.
- A3 SUS316LTP (1.6x0.3x2000) 228-50579-91 qty 5, I.D. 0.3 mm × 2000 mm: 1 pc for LC-40D–T-joint and 4 pc for Cell–SFC-30A; use 1 pc for MS makeup pump outlet piping and 4 pc for delay capacity adjustment piping.
- A4 PEEK TUBE (0.13x3000) 228-33833-91, I.D. 0.13 mm × 3000 mm: cut as needed to reach MS; cut 200 mm for T-joint–LCMS and 164 mm for T-joint–coupling.
- A5 FEMALE,1.6FT316L-0.4 228-16008-11 qty 3; A6 Coupling 1.6C-0.4 316L 228-16004-13 qty 5.
- A7 Drain tube 228-25495-93 qty 1; when using ELSD, connect with PEEK tube of 0.25 mm I.D. instead of the drain tube (sold separately, 228-33833-91 PEEK TUBE 0.25×3000).
- A8 Ferrule 1.6F 316L 228-16000-10 qty 16; A9 Male Nut 1.6MN 228-16001 qty 16; A10 Male Nut 1.6MN PEEK 228-35403 qty 5 for both ends of A4*2 and A4*3 and No. 6 connections.
- A11 CV,OUT-UHP TP 228-53334-96 qty 1 is a check valve to prevent backflow; A12 Pipe bands qty 3 for bundling delay pipe (A3).
Proporciona diagramas de tuberías que muestran dónde se utiliza cada símbolo de kit en los sistemas Online SFE-SFC-MS, Analytical Fraction, Analytical Fraction MS, SFC-MS, pretratamiento SFE (FRC-40 SF y FRC-10A), Chiral Screening, Column Switching 6/+6 para I.D. 0.1 mm, y SFC-UV/PDA. El manual remite a la sección 2.1.3 de la Nexera UC System Guide para ejemplos de tuberías de líneas de flujo analítico.
- Online SFE-SFC-MS System diagram.
- Analytical Fraction System and Analytical Fraction MS System diagrams.
- SFC-MS System and Piping Kit MS for I.D.0.1 mm diagram.
- SFE pretreatment system diagrams for FRC-40 SF and FRC-10A.
- Chiral Screening System diagram.
- Piping Kit Column Switching 6/+6 for I.D.0.1 mm diagram.
- SFC-UV/PDA System diagram.
Key Integration, Operating & Safety Requirements
| Specification / Condition | Engineering Implication | Aplica a |
|---|---|---|
| Los kits de tuberías de I.D. 0.1 mm (m, c, p) sustituyen la tubería estándar de I.D. 0.3 mm para reducir el volumen muerto del sistema. p.1 ↗ | Select an I.D. 0.1 mm kit when reduced dead volume is required; otherwise the standard I.D. 0.3 mm kit applies. | m (228-63782-41), c (228-63783-41/-43), p (228-63783-42/-44) |
| El kit Column Switching 6 228-61105-43 es para FCV-34AH y el 228-61105-45 es para FCV-0607. p.1 ↗ | Order the kit variant matching the installed FCV valve model. | C kit |
| El kit Column Switching +6 228-61105-44 es para FCV-34AH y el 228-61105-46 es para FCV-0607. p.1 ↗ | Order the kit variant matching the installed FCV valve model. | P kit |
| El kit Column Switching 6 de I.D. 0.1 mm 228-63783-41 es para FCV-0607 y el 228-63783-43 es para FCV-34AH. p.1 ↗ | The -43 variant includes ferrules 670-11412-04 (qty 7) and bushes 670-11412-02 (qty 6) and 670-11412-03 (qty 1) for FCV-34AH connections. | c kit |
| El kit Column Switching +6 de I.D. 0.1 mm 228-63783-42 es para FCV-0607 y el 228-63783-44 es para FCV-34AH. p.1 ↗ | The -44 variant includes ferrules 670-11412-04 (qty 7) and bushes 670-11412-02 (qty 6) and 670-11412-03 (qty 1) for FCV-34AH connections. | p kit |
| El tubo de puerto de inyección B16 del kit Basic tiene I.D. Φ0.17 mm (228-64106-49) y se utiliza para SIL-40 Loop Injection. p.2 ↗ | Use this specific injection port pipe when configuring SIL-40 loop injection. | B kit |
| La válvula de retención M4 Check Valve 228-53334-96 del kit MS sustituye el filtro de línea de la bomba de reposición. p.2 ↗ | Remove the makeup pump line filter and install the check valve in its place when using the MS kit. | M kit |
| La válvula de retención H5 Check valve 228-53334-96 del kit de gas de alta presión debe sustituirse por un filtro de línea. p.4 ↗ | In the high-pressure gas kit, the check valve position is replaced by a line filter. | H kit |
| El amortiguador E5 Cushion del kit SFE se inserta entre la placa de montaje del mezclador y el lateral de la bomba como material protector; el tornillo de fijación E6 Bind Screw M4x8 fija un punto en el lateral de la bomba. p.3 ↗ | Follow this mounting arrangement when installing the mixer in the SFE pretreatment system. | E kit |
| La válvula de retención F2 CV,OUT-30ADSF 228-45705-41 del kit de modificación Prep SFC debe orientarse con el lado de la unión de válvula aguas arriba y el lado de la válvula de retención aguas abajo. p.6 ↗ | Incorrect orientation will prevent proper check-valve function. | F kit (228-75753-42) |
| La válvula de retención f4 CV,OUT-30ADSF 228-45705-41 del kit de modificación Analytical SFC debe orientarse con el lado de la unión de válvula aguas arriba y el lado de la válvula de retención aguas abajo. p.6 ↗ | Incorrect orientation will prevent proper check-valve function. | f kit (228-79729-41) |
| F8 PLUG 228-16006-10 cant. 3 del kit Prep SFC: utilice tapones de cierre en el puerto 3 de FCV (R) y en los puertos 3 y 6 de FCV (L); si la válvula no se cierra con un tapón de cierre, puede producirse fuga según la posición de la válvula. p.6 ↗ | Always plug the specified unused FCV ports to prevent leakage. | F kit (228-75753-42) |
| f11 PLUG 228-16006-10 cant. 1 del kit Analytical SFC: utilice tapón de cierre en el puerto 3 de FCV; si la válvula no se cierra, puede producirse fuga. p.6 ↗ | Always plug the specified unused FCV port to prevent leakage. | f kit (228-79729-41) |
| A3 SUS316LTP (1.6x0.3x2000) 228-50579-91 cant. 5 del kit Analytical Fraction MS: utilice 1 ud. para la tubería de salida de la bomba de reposición del MS y 4 ud. para la tubería de ajuste de capacidad de retardo (LC-40D–unión en T 1 ud.; Cell–SFC-30A 4 ud.). p.7 ↗ | Allocate the five tubes exactly as specified to achieve the intended delay volume. | A kit (228-68817-41) |
| A4 PEEK TUBE (0.13x3000) 228-33833-91 del kit Analytical Fraction MS: corte 200 mm para unión en T–LCMS y 164 mm para unión en T–acoplamiento; corte lo necesario para alcanzar el MS para unión en T–unión en T. p.7 ↗ | Use these cut lengths to maintain the intended flow path geometry. | A kit (228-68817-41) |
| Cuando se utiliza ELSD con el kit Analytical Fraction MS, conecte con un tubo de PEEK de I.D. 0.25 mm en lugar del tubo de drenaje A7 (vendido por separado, 228-33833-91 PEEK TUBE 0.25×3000). p.7 ↗ | Do not use the standard drain tube with ELSD; use the specified PEEK tube. | A kit (228-68817-41) |
| A11 CV,OUT-UHP TP 228-53334-96 del kit Analytical Fraction MS es una válvula de retención para prevenir el reflujo. p.7 ↗ | Install it to protect the flow path from backflow. | A kit (228-68817-41) |
| Los elementos X1 (SUS Sleeve Tubing 0.3x300, 228-53137-42, cant. 2), X2 (SUS Sleeve Tubing 0.3x1200, 228-53184-41, cant. 1) y X3 (FEMALE,1.6FT316L-0.4, 228-16008-11, cant. 1) del kit Prep SFC no están incluidos en el kit. p.6 ↗ | Order these items additionally when installing the Prep SFC modification kit. | F kit (228-75753-42) |
| B3 SUS Sleeve Tubing (0.3x1200) 228-53184-41 cant. 2 del kit Basic se utiliza para bomba de modificador–mezclador y bomba de CO2–mezclador; B4 (0.3x700) 228-53184-93 se utiliza para unión en T–columna y, solo en el Chiral Screening System, mezclador–válvula de alta presión. p.2 ↗ | Route these tubes to the specified connections; B4 has an additional use only on the Chiral Screening System. | B kit |
| B6 ETFE Tubing (1.6x1.0x2000) 228-18495-03 del kit Basic es para tubo de drenaje y se utiliza solo en el Chiral Screening System. p.2 ↗ | Install B6 only when configuring the Chiral Screening System. | B kit |