Best Practices for Analysis of IVT mRNA by Fragment Analyzer
Contenido
Overviewpp. 1-2
Introduces best practices for IVT mRNA analysis workflow
Procedurepp. 3-4
Master mix preparation and vortexing steps
Procedurepp. 5-5
Heat denaturation requirements for RNA Ladder
Qualitypp. 6-6
Sample and reagent stability considerations
Qualitypp. 7-7
Reproducibility of Fragment Analyzer instrument results
Specpp. 8-10
Dynamic range and serial dilution analysis examples
pp. 11-11
Summary of best practices recommendations
pp. 12-12
Agilent website and contact information
p. 2table, 10 rows
Table 1. List of IVT mRNA samples used in this study and their sequence size.
Reaction Number
Sequence Size (nt)
1
212
2
410
3
493
4
894
5
996
6
1,902
7
2,055
8
3,900
9
4,053
10
5,979
Engineering Facts
12 facts · every claim linked to a page
Operation
Proper mixing of IVT mRNA with the RNA Diluent Marker is required for reliable analysis; unmixed samples show large variation in peak intensity affecting reported concentration and percent total.
Without proper mixing, concentration and purity results are unreliable, so the sample preparation protocol must include a validated mixing step.
Source
“This data provides evidence that proper mixing of IVT mRNA samples is necessary for reliable sample analysis.”
Operation
Heat denaturation at 70 °C for 2 minutes followed by snap cooling to 4 °C sharpens peaks and can influence reported purity, though size remains consistent.
Operators must decide whether to heat denature based on sample secondary structure, since it affects peak shape and potentially purity readout.
Source
“heat denaturation results in a sharper peak. This change in sample distribution may impact peak heights and thus could influence the reported purity of the sample.”
Operation
The RNA Ladder must be heat denatured for accurate sizing; without it, secondary structures cause split peaks and inconsistent peak heights.
Sizing accuracy depends on proper ladder preparation, so the ladder must always be heat denatured before running the assay.
Source
“Heat denaturation is required for the RNA Ladder.”
Operation
IVT mRNA samples prepared with the RNA Diluent Marker are stable at room temperature for approximately 10 hours, allowing multiple plate rows to be run without degradation concerns.
This defines the maximum bench time for prepared samples and supports scheduling of multi-plate runs without re-preparation.
Source
“The IVT mRNA samples analyzed were stable at room temperature for 10 hours, providing sufficient time to analyze many rows of samples on the Fragment Analyzer without having to worry about degradation.”
Performance
Across four Fragment Analyzer systems, size %CV was less than 0.5% and size percent error was less than 8% for the 212 nt sample, less than 3% for 894 nt, and less than 1.5% for 1,902 nt.
This quantifies instrument-to-instrument reproducibility, which is critical when selecting or qualifying multiple systems for a QC lab.
Source
“is consistent between all instruments with a %CV of less than 0.5% for each sample.”
Operation
For accurate IVT mRNA quantification and to determine loading concentration, UV-Vis methods are recommended because fluorescent dyes may not bind IVT mRNA with appropriate affinity.
Using the wrong quantification method leads to incorrect loading concentrations and unreliable size/purity results.
Source
“for the most accurate quantification of IVT mRNA, and to determine the concentration at which to load samples onto the Fragment Analyzer, it is recommended to use UV-Vis methods.”
Operation
The maximum recommended peak height is approximately 24,000 RFU to avoid cross-talk between wells; higher peaks require dilution and reanalysis.
Exceeding this threshold causes signal cross-talk in adjacent wells, corrupting data, so loading concentration must be controlled.
Source
“The maximum peak height recommendation is approximately 24,000 RFU to avoid cross-talk.”
Operation
Samples must be run at high enough concentration to detect small impurities; if too low, impurity peaks are not integrated and reported percent purity is overestimated.
Purity assessment is a primary QC goal, so the input concentration must be optimized to avoid false-high purity results.
Source
“If the concentration tested is too low, these impurity peaks may be too small to be successfully integrated in the electropherogram, and the reported percent purity will be overexaggerated.”
Operation
The minimum peak height in ProSize software can be adjusted to ensure all peaks are integrated for better purity analysis.
Software integration settings directly affect reported purity, so analysts must configure the minimum peak height appropriately.
Source
“Within the Agilent ProSize data analysis software, the minimum peak height can be adjusted to ensure that all peaks are successfully integrated, thus allowing for better analysis of sample purity.”
Operation
Recommended starting sample concentration range is 1 to 100 ng/µL, but concentration should be optimized for each transcript type because IVT mRNA behavior varies with sequence and composition.
This gives the initial loading range for method development, while acknowledging that each transcript requires optimization.
Source
“it is recommended to start sample analysis within the recommended range of 1 to 100 ng/µL”
Selection
The Agilent RNA kit (15 nt), part number DNF-471, is the specified kit for IVT mRNA size and purity assessment on the Fragment Analyzer systems.
This identifies the exact consumable part number required for the application, which is essential for procurement and method setup.
Source
“the size and purity were assessed using the Agilent 5200 and 5300 Fragment Analyzer systems with the Agilent RNA kit (15 nt) (part number DNF-471).”
Operation
The Fragment Analyzer can hold up to three 96-well sample plates and run multiple sample rows consecutively, enabling batch processing.
This capacity determines throughput planning and whether the instrument fits the lab's batch size requirements.
Source
“The Fragment Analyzer system can hold up to three 96-well sample plates and can be programmed to run multiple sample rows consecutively.”