Quick Reference 5973N MSD 6890 GC
Technical Reference Summary
Covered Models & Document Scope
Referencia rápida para operar un MSD 5973N (detector selectivo de masas) con un GC 6890 usando el software MSD Productivity ChemStation Rev. D.00.00; cubre las variantes EI y CI del MSD, inyección automática (ALS) y manual, y los menús del software en modo Enhanced.
Section-by-Section Technical Breakdown
Describe la vista principal del ChemStation para configurar y monitorear los parámetros del instrumento. Explica el estado de adquisición, los botones de inicio/parada, el reloj de tiempo de ejecución y los botones para inyector, entradas, columnas, horno, auxiliar (interfaz GC/MSD) y parámetros del MSD.
- Start button is green when no run is in progress; click it, fill sample information, and click Start Run.
- Stop button is red during Pre-Run, Run, or Post-Run mode.
- Oven ready indicator: green square when GC is ready, red when not ready.
- Aux button sets the GC/MSD interface temperature (usually Thermal Aux 2).
- MS button edits MS acquisition parameters, selects tune file, or edits MS monitors.
Enumera los comandos de menú disponibles en las vistas Top, Instrument Control, Diagnostics/Vacuum Control, Manual Tune, Data Analysis, EasyID, QEdit, Parametric Retrieval, Align GC, Review Peak Purity, Quick Screener y RTLock. Estos menús proporcionan acceso al control del instrumento, sintonización, análisis de datos y diagnóstico de vacío.
- Diagnostics/Vacuum Control menu includes Pump Down, Vent, MS ON, MS OFF, Set RFPA, Air and Water Check, and MS Error Codes.
- Manual Tune menu includes Autotune, Low Mass Autotune, Standard Spectra Tune, DFTPP Tune, BFB Tune, Target Tune, QuickTune, and calibration/ramp functions.
- Data Analysis menu includes quantitation, library search, integration, and reporting tools.
- RTLock menu provides retention time locking setup and calibration.
Procedimiento paso a paso para ventear el MSD de forma segura, incluyendo apagar el controlador del medidor, cerrar el gas reactivo para MSD CI, ajustar los calentadores a temperatura ambiente, apagar la alimentación y abrir la válvula de venteo 3/4 de vuelta. Incluye advertencias de seguridad para gas portador de hidrógeno y superficies calientes.
- Set GC/MSD interface heater and GC oven to ambient (25°C) before venting.
- Turn vent valve knob counterclockwise only 3/4 turns or until hissing is heard.
- On a CI MSD, the Gas Off light must be on when venting.
- If using hydrogen carrier gas, carrier gas flow must be off before turning off MSD power.
- Do not put ChemStation into Top view while MSD is vented; this turns on the interface heater.
Precondiciones y procedimiento para bombear el MSD. Requiere válvula de venteo cerrada, sellos de vacío seguros, alimentación conectada a tierra, columna acondicionada, gas portador con pureza de al menos 99.999% y escape de línea frontal adecuado. Después del bombeo, espera a que la bomba turbomolecular alcance el 95% y el equilibrio térmico.
- Carrier gas purity must be at least 99.999% with recommended traps.
- If hydrogen is used, carrier gas flow must be off and front sideplate thumbscrew loosely fastened.
- Rough pump gurgling noise should stop within a minute; continued noise indicates a large air leak.
- Turbo pump should reach 80% within 10–15 minutes and eventually 95%.
- After 'Ok to run' appears, wait two hours for thermal equilibrium before tuning or acquiring data.
Explica los procedimientos de autotune y sintonización manual. Las opciones de autotune incluyen Autotune, Low Mass Autotune, Standard Spectra Tune y QuickTune. La sintonización manual permite el ajuste interactivo de voltajes de lentes y masas de sintonización, con barridos de perfil y espectro.
- Always tune with the same GC oven temperature, column flow, and analyzer temperature used for data acquisition.
- Autotune gives maximum sensitivity over the full scan range.
- Standard Spectra Tune gives standard response over full scan range and may reduce sensitivity.
- QuickTune adjusts peak width, mass assignment, and abundance without changing ion ratios.
- Manual tune can provide greater sensitivity than autotune and allows ramping of individual parameters.
Describe la configuración del GC para uso con MSD, inyección con automuestreador e inyección manual. Incluye la verificación de tipos de entrada/inyección, calentador del canal auxiliar 2 y configuración de columna con detector MSD y salida de vacío.
- Select Instrument / Inlet/Injection Types, choose injection source, and select Use MS checkbox.
- Verify Aux channel 2 heater is on and set to desired temperature with MSD selected as Type.
- Verify column detector is MSD and Vacuum is selected for Outlet psi.
- For autosampler, specify unique data file name and vial position (1–100).
- For manual injection, press Prep Run key on GC keypad before starting run.
Cubre la carga de archivos de datos, integración de cromatogramas, selección de espectros, zoom, promediado de espectros, suma/resta de espectros y sustracción de fondo. Estas operaciones se realizan en la vista Data Analysis.
- Load data file via File / Load; chromatogram appears in window [2].
- Integrate via Chromatogram / Integrate; select integrator first if needed.
- Double-click right mouse button on chromatogram to select a spectrum.
- Subtract Background (BSB) subtracts selected spectrum from every scan and stores result in BSB subdirectory.
- Zoom out by double-clicking left mouse button in zoomed window.
Procedimientos para integrar y buscar picos contra bibliotecas espectrales, y para buscar un solo espectro. Los informes de búsqueda en biblioteca se pueden enviar a pantalla, impresora o archivo.
- Select Spectrum / Library Search Report to integrate TIC and search each peak.
- Choose Summary or Detailed report format and destinations (Screen, Printer, File).
- Select spectrum from each peak: Apex, Apex - Start of Peak, Apex - Background at time, or Peak Average.
- For single spectrum search, double-click right mouse button in spectrum window.
- Statistics button shows quality of each library hit.
Describe el procedimiento de bloqueo de tiempo de retención (RTL) para anular los cambios de tiempo de retención debidos a cambios de columna. Implica recopilar datos a cinco presiones de entrada (-20%, -10%, nominal, +10%, +20%) y generar una curva de presión/tiempo de retención.
- RTL calibration runs are stored as RTLOCK1.D through RTLOCK5.D in method directory under RTLOCK folder.
- Five runs are made automatically at -20%, -10%, nominal, +10%, and +20% pressure.
- Curve equation based on retention time vs. pressure is generated.
- Locked method title bar indicates method is locked and which compound was used.
- When a locked method is run, pressure is restored to locked pressure even if changed via GC keypad or Instrument Control.
Consejos prácticos para operar el sistema GC/MSD, incluyendo respaldo de datos, selección de archivo de sintonización, programación de mantenimiento, tiempo de espera de bombeo, caudales de columna, técnicas de inyección y selección de modo SIM/Scan.
- After pumpdown, wait at least 2 hours for thermal equilibrium before tuning or acquiring data.
- Optimum sensitivity generally occurs at column flow rates of 1.2 ml/minute or less.
- For injections greater than 1 µL, use pulsed splitless mode and increase initial oven temperature 10–20°C.
- For splitless injections, a pulse pressure of twice the initial inlet pressure is typical.
- Use Constant Flow mode for most efficient separation and constant sensitivity.
- For SIM, use exact mass from Tabulation report, not nominal mass.
- Use low resolution mode for SIM unless determining ratios of masses one amu apart.
Enumera síntomas comunes y sus causas probables, incluyendo mensajes de estado, problemas de forma de pico, problemas de sensibilidad, deriva del tiempo de retención, alto ruido de fondo y problemas de vacío. Remite al MSD Hardware Manual y al GC Maintenance and Troubleshooting Manual para más detalles.
- Status flashing 'Server not found! Check LAN connection' is normal initially; if persistent, check for power failure or bad connection.
- No peaks: check sample concentration, syringe installation, vial, injection mode.
- Tailing peaks: active sites, injection too large, injection port too cool, column flow too low, interface or ion source too cool.
- Poor sensitivity: incorrect tuning, tune file mismatch, incorrect temperatures, leaks, dirty ion source, air leak, filament, mass filter polarity.
- Foreline or vacuum manifold pressure too high: excessive column flow, air leak, diffusion pump fluid level/contamination, foreline pump oil level/contamination, constricted foreline hose.
Proporciona un programa de tareas de mantenimiento diarias, semanales, mensuales, trimestrales, semestrales y anuales, además de tareas según sea necesario. Incluye advertencias de seguridad para el mantenimiento.
- Daily: check/replace septum, check tightness of injection port liners and column nuts.
- Weekly: check foreline pump fluid level, change injection port liners and O-rings.
- Monthly: clean split/splitless inlet vent line trap, check for leaks.
- Every three months: replace gas cylinders when below 500 psig.
- Every six months: replace foreline pump fluid, refill calibration vial if needed.
- Every year: check/replace diffusion pump fluid, recondition/replace traps and chemical filters.
- As needed: tune MSD, clean ion source, replace carrier gas trap, replace worn parts, replace column, lubricate seals.
Key Integration, Operating & Safety Requirements
| Specification / Condition | Engineering Implication | S'applique à |
|---|---|---|
| La pureza del gas portador debe ser de al menos 99.999% con trampas recomendadas. p.17 ↗ | Use high-purity carrier gas and appropriate traps to prevent contamination and ensure proper MSD operation. | 5973N MSD with 6890 GC |
| Si se usa hidrógeno como gas portador, el flujo de gas portador debe estar apagado y el tornillo de mariposa de la placa lateral frontal debe estar ligeramente apretado antes del bombeo. p.17 ↗ | Prevents hydrogen accumulation and explosion risk; follow Hydrogen Carrier Gas Safety Guide (5955-5398). | 5973N MSD with hydrogen carrier gas |
| Después del bombeo, espere dos horas para que el MSD alcance el equilibrio térmico antes de sintonizar o adquirir datos. p.17 ↗ | Data acquired before thermal equilibrium may not be reproducible. | 5973N MSD |
| La bomba turbomolecular debe alcanzar el 80% de velocidad en 10 a 15 minutos y eventualmente el 95%. p.17 ↗ | If pump speed does not reach these levels, check for air leaks or vacuum problems. | 5973N MSD with turbo pump |
| La sensibilidad óptima generalmente ocurre con caudales de columna de 1.2 ml/minuto o menos. p.23 ↗ | Use column flow rates at or below 1.2 ml/min for best sensitivity. | 5973N MSD with 6890 GC |
| Al inyectar volúmenes mayores a un microlitro, use modo splitless pulsado y aumente la temperatura inicial del horno 10–20°C. p.23 ↗ | Improves sample transfer and peak shape for large injections. | 5973N MSD with 6890 GC |
| Para inyecciones splitless, es típica una presión de pulso del doble de la presión inicial de entrada. p.23 ↗ | Provides more quantitative sample transfer onto the column. | 5973N MSD with 6890 GC |
| Al elegir masas para SIM, use la masa exacta impresa en el informe de tabulación, no la masa nominal anotada en la pantalla del espectro. p.23 ↗ | Provides more accurate SIM data. | 5973N MSD with ChemStation |
| Para análisis SIM, use modo de baja resolución a menos que se determinen relaciones de masas separadas por una uma. p.23 ↗ | Low resolution provides maximum sensitivity and repeatability. | 5973N MSD with ChemStation |
| Ajuste el calentador de la interfaz GC/MSD y el horno del GC a temperatura ambiente (25°C) antes de ventear el MSD. p.16 ↗ | Ensures safe venting and prevents damage to components. | 5973N MSD |
| Gire la perilla de la válvula de venteo en sentido antihorario solo 3/4 de vuelta o hasta que se escuche un silbido. p.16 ↗ | Prevents O-ring from falling out of its groove; retighten knob before pumping down. | 5973N MSD |
| En un MSD CI, la luz Gas Off debe estar encendida cuando el MSD se está venteando. p.16 ↗ | Ensures reagent gas flow is off and isolation valve is closed. | 5973N MSD CI variant |
| Cuando se ejecuta un método bloqueado, la presión se restaura al valor de presión bloqueado incluso si se realizaron cambios usando el teclado del GC o Instrument Control. p.22 ↗ | Retention time locking overrides manual pressure changes; ensure method is unlocked if pressure changes are needed. | 5973N MSD with ChemStation RTLock |
| La calibración RTL recopila datos a cinco presiones de entrada: -20%, -10%, nominal, +10% y +20% del punto de ajuste actual del método. p.22 ↗ | Generates pressure/retention time curve for locking; five runs are made automatically. | 5973N MSD with ChemStation RTLock |
| Reemplace los cilindros de gas cuando la presión esté por debajo de 500 psig. p.26 ↗ | Prevents contamination and ensures consistent gas supply. | 5973N MSD with 6890 GC |
| Verifique el nivel de fluido de la bomba de línea frontal cada semana y reemplace el fluido cada seis meses. p.26 ↗ | Maintains proper vacuum and prevents pump damage. | 5973N MSD |
| Limpie la trampa de la línea de venteo de la entrada split/splitless cada mes. p.26 ↗ | Prevents contamination and maintains proper inlet performance. | 6890 GC with split/splitless inlet |
| Para inyección manual, presione la tecla Prep Run en el teclado del GC para cancelar el flujo de ahorro de gas, llevar el flujo de entrada al punto de ajuste y cerrar la válvula de purga (solo para inyección splitless). p.19 ↗ | Prepares the GC for manual injection and ensures proper sample transfer. | 5973N MSD with 6890 GC manual injection |
| No use el botón Start en el GC para iniciar una ejecución cuando use el automuestreador. p.19 ↗ | Use the ChemStation software to start runs with the autosampler to avoid inconsistent results. | 5973N MSD with 6890 GC and ALS |
| No ponga el ChemStation en la vista Top cuando el MSD esté venteado; hacerlo encenderá el calentador de la interfaz. p.16 ↗ | Prevents overheating and potential damage during venting. | 5973N MSD |
Faults & Troubleshooting
| Code / Symptôme | Possible Cause | Remedy | Note |
|---|---|---|---|
| Server not found! Check LAN connection p.24 ↗ | Normal when MSD is initially turned on; if flashing continues after pumpdown initiated: temporary power failure interrupted communications, or bad connection between MSD and ChemStation and/or hub. | Check power and LAN connections; if persistent, refer to MSD Hardware Manual or online help. | Troubleshooting Tips |
| No peaks p.24 ↗ | Incorrect sample concentration; no analytes present; syringe missing or not installed correctly (ALS only); empty sample vial; injection in split mode instead of splitless mode. | Check sample concentration, syringe installation, vial, and injection mode. | Troubleshooting Tips |
| Tailing peaks p.24 ↗ | Active sites in sample path; injection too large; injection port too cool; column flow too low; GC/MSD interface or ion source too cool. | Check for active sites, reduce injection volume, increase temperatures, increase column flow. | Troubleshooting Tips |
| Peaks with flat tops p.24 ↗ | Solvent delay time too short; display scale is wrong; injection too large; electron multiplier voltage too high. | Adjust solvent delay, display scale, injection volume, or EM voltage. | Troubleshooting Tips |
| Peaks with split tops p.24 ↗ | Bad injection technique; injection too large. | Improve injection technique or reduce injection volume. | Troubleshooting Tips |
| Rising baseline p.24 ↗ | Column bleed; other contamination. | Condition column or check for contamination. | Troubleshooting Tips |
| Retention time (RT) drift p.24 ↗ | Column has been shortened (shorter RT); old column (shorter RT); active sites in sample path (longer RT); reduced column flow (longer RT); injection port leak (longer RT); initial oven temperature changed (up = shorter RT, down = longer RT). | Check column, flow, leaks, and oven temperature program. | Troubleshooting Tips |
| Poor sensitivity p.24 ↗ | Incorrect tuning; tune file does not match type of analysis; incorrect temperatures; incorrect sample concentration; leaking injection port; incorrect split ratio; purge off time in splitless mode too short; excessive pressure in the MSD; dirty ion source; air leak; detector is not working correctly; poor filament operation; incorrect mass filter polarity. | Check tuning, temperatures, concentrations, leaks, split ratio, purge time, pressure, ion source cleanliness, detector, filament, and mass filter polarity. | Troubleshooting Tips |
| Poor repeatability p.25 ↗ | Dirty syringe needle; leaking injection port; mismatched injection port liner and injection size; loose column connections; variations in pressure, column flow, and temperature; dirty ion source; loose connections in the analyzer; ground loop. | Clean syringe, check for leaks, match liner to injection size, tighten connections, stabilize pressure/flow/temperature, clean ion source, check for ground loops. | Troubleshooting Tips |
| Inconsistent peakwidths p.25 ↗ | Incorrect tuning; no PFTBA in calibration vial; calibration valve failure; dirty ion source; worn out electron multiplier; MSD has not had enough time to reach thermal equilibrium; large variations in the temperature of the lab. | Check tuning, calibration vial, calibration valve, ion source, electron multiplier, allow thermal equilibrium, stabilize lab temperature. | Troubleshooting Tips |
| High background in mass spectra p.25 ↗ | Air leak; foreline or vacuum manifold pressure too high; other contamination. | Check for air leaks, vacuum pressure, and contamination. | Troubleshooting Tips |
| Ions at m/z 18, 28, 32, and 44 p.25 ↗ | Detector vented recently (residual air and water); air leak. | Allow system to pump down longer; check for air leaks. | Troubleshooting Tips |
| Isotopes missing or isotope ratios incorrect p.25 ↗ | Incorrect tuning; dirty ion source; high background; electron multiplier voltage too high; repeller voltage too high; high scan speed (Scan mode); low dwell time (SIM mode); peaks too wide or too narrow; repeller and ion focus leads have been reversed. | Check tuning, clean ion source, reduce background, adjust EM and repeller voltages, scan speed, dwell time, peak width, and verify lead connections. | Troubleshooting Tips |
| Foreline or vacuum manifold pressure too high p.25 ↗ | Excessive column flow; air leak; diffusion pump fluid level too low; diffusion pump fluid is contaminated; foreline pump oil level too low; foreline pump oil is contaminated; constricted foreline hose (this would cause the vacuum manifold pressure to be too high but the foreline pressure to be too low). | Check column flow, air leaks, diffusion pump fluid level and condition, foreline pump oil level and condition, and foreline hose for constriction. | Troubleshooting Tips |