Cary Eclipse Fluorescence Spectrophotometer User's Guide
Technical Reference Summary
Covered Models & Document Scope
Cubre el sistema Agilent Cary Eclipse Fluorescence Spectrophotometer, incluido el soporte de celda única estándar, los soportes de muestra opcionales, los accesorios de purga con nitrógeno, el software Cary Eclipse WinFLR y el convertidor National Instruments USB-GPIB-HS. Número de referencia del manual 8510175800, edición 7, septiembre de 2016.
Section-by-Section Technical Breakdown
Define las condiciones ambientales para el transporte y el funcionamiento, el peso y las dimensiones del instrumento, los requisitos de alimentación, las conexiones eléctricas, la capacidad del fusible, la presión de suministro de nitrógeno y la ubicación del ordenador. El instrumento es para uso en interiores únicamente, grado de contaminación 2, categoría de instalación II (EN 61010-1).
- Operating temperature within performance specifications: 10–35 °C at 0–853 m altitude; 10–25 °C at 853–2133 m altitude.
- Recommended ambient temperature for optimum analytical performance: 20–25 °C, held constant to within ±2 °C throughout the working day.
- Power: 100–240 VAC, 50–60 Hz, approximately 180 VA.
- Fuse: T3.15 AH 250 V (5 x 20 mm) IEC127 Sheet 5.
- Nitrogen supply: 70 kPa (10 psi).
- Front accessory connection: 25-pin D-range connector; rear: IEEE 488 (GPIB Cary Eclipse system connection).
- Sample compartment connectors: 9-pin, 15-pin, and 25-pin D-range connectors (low voltage AC/DC).
Describe la instalación del soporte de celda única estándar, el ajuste de altura e inclinación de la cubeta y la alineación del soporte de celda mediante la aplicación Align y una muestra fluorescente. Incluye detalles de ajuste mecánico y las herramientas necesarias.
- Cell holder base is positioned on locating pins and locked by turning the lever to the right.
- Cuvette height is raised by turning the cell lifter clockwise and lowered counter-clockwise; downward movement requires pushing the cuvette down due to spring tension.
- Pitch adjustment screw requires a 2.5 mm hex key; clockwise raises the front of the cell holder.
- Alignment uses a fluorescent sample (e.g., anthracene) in a microcell and a 540 nm wavelength to check beam passage.
- Pitch adjustment is optimized by observing the intensity of light striking white paper in the beam path.
Especifica los requisitos del sistema de purga con nitrógeno, incluidos la calidad del gas, la regulación de presión, la tubería de suministro, el colector de gas y el caudalímetro. El sistema de purga no lo suministra Agilent.
- Liquid nitrogen (with heat exchanger) is recommended; compressed nitrogen must be dry, oil-free, and uncontaminated.
- Never use compressed nitrogen from a supplier using oil or water in the compression process.
- Operating pressure is from 70 kPa (10 psi); use an appropriate regulator and gauge.
- Supply tubing: clean, flexible PVC or equivalent, 6 mm (1/4 in) internal diameter; never use rubber tubing.
- Flowmeter should monitor flow rates between 0 and 30 liters per minute (64 cubic feet per hour).
Proporciona instrucciones paso a paso para instalar, registrar y desinstalar el software Cary Eclipse WinFLR y la Ayuda, y para instalar el convertidor National Instruments USB-GPIB-HS. Incluye notas sobre el tiempo de instalación y los avisos del controlador.
- Install Cary Eclipse WinFLR software before installing the USB-GPIB-HS converter.
- During .Net Framework and GPIB driver installation, the computer may appear frozen for 3 to 5 minutes; do not exit the installation.
- The Product Key is found on the cover of the Agilent Cary Eclipse software CD/DVD case.
- During uninstallation, click 'No' when prompted to remove drivers/files that other programs may rely on.
- Read the Software Status Bulletin and Agilent Cary Eclipse WinFLR Release Notes.pdf in the install directory.
Detalla el procedimiento para extraer e instalar el módulo de lámpara de destello de xenón, incluidas las precauciones de seguridad, y el procedimiento de alineación mediante la aplicación Align con los parámetros del instrumento especificados. El módulo de lámpara debe alinearse después de la sustitución.
- Always disconnect the Cary Eclipse from the mains supply before changing the lamp module.
- Remove the lamp access panel, turn the instrument onto its right side, remove four thumb screws from the lamp module cover, and loosen three bolts marked with a black dot.
- Disengage two guide pins at the rear and disconnect the plug by squeezing the clip.
- Alignment parameters: Ex. Wavelength 540 nm, Ex. Slit 1.5 nm, Ave. time 0.1 s, PMT voltage Medium.
- Adjust the bottom left screw (vertical) and top right screw (horizontal) for maximum signal using the supplied 5.5 mm nut driver.
- Click 'Save conditions' to store instrument parameters and the maximum reading.
Describe la ubicación y la sustitución de los dos fusibles en la parte posterior del instrumento, la interpretación del código de fusible y el procedimiento de comprobación. La fusión repetida de fusibles puede indicar otros problemas del instrumento.
- The Cary Eclipse contains two fuses located at the back of the instrument.
- Replace a blown fuse with one of the same type and rating as indicated in Chapter 2 (T3.15 AH 250 V).
- Fuse code: 'T' = time lag, 'F' = fast-acting; current rating in amperes; 'H' = heavy, 'L' = low breaking capacity; voltage rating in volts.
- Always ensure the code on the fuse cap matches the information printed next to the fuse holders.
- If a fuse repeatedly blows, it may indicate other problems with the instrument.
Proporciona soluciones para problemas comunes: instrumento fuera de línea, botón Connect en lugar de Start y prueba de rendimiento del instrumento que no cumple las especificaciones. Incluye comprobaciones de reinicio del software, conexiones de cables, inicialización, pulsación de la lámpara y alineación de la lámpara.
- Instrument offline: restart computer after software installation, check USB-GPIB-HS cable connection, ensure initialization tests complete before starting software.
- Connect button instead of Start: check for other Cary applications running; click Connect to gain control if they are not collecting data.
- Performance test failure: ensure sample compartment is empty, cable retaining screws are tightened, lamp is pulsing (green power indicator flashing), and lamp is correctly aligned.
- If the lamp is not pulsing, there may be a hardware conflict.
Key Integration, Operating & Safety Requirements
| Specification / Condition | Engineering Implication | S'applique à |
|---|---|---|
| La temperatura de funcionamiento dentro de las especificaciones de rendimiento es de 10–35 °C a altitudes de 0–853 m y de 10–25 °C a altitudes de 853–2133 m. p.18 ↗ | Install the instrument in a temperature-controlled laboratory; higher altitudes require reduced ambient temperature to maintain performance. | Whole series |
| Para un rendimiento analítico óptimo, la temperatura ambiente debe ser de 20–25 °C y mantenerse constante dentro de ±2 °C durante toda la jornada de trabajo. p.18 ↗ | Use a stable laboratory HVAC system to avoid drift in fluorescence measurements. | Whole series |
| Requisito de alimentación: 100–240 VAC, 50–60 Hz, aproximadamente 180 VA. p.19 ↗ | Ensure the mains supply and circuit capacity are adequate; use the country-specific Agilent-supplied power cord. | Whole series |
| Capacidad del fusible: T3.15 AH 250 V (5 x 20 mm) IEC127 Hoja 5. p.20 ↗ | Replace blown fuses only with the specified type and rating; verify the code on the fuse cap matches the label next to the fuse holder. | Whole series |
| La presión de funcionamiento del suministro de nitrógeno es a partir de 70 kPa (10 psi). p.20 ↗ | Use an appropriate pressure regulator and gauge to maintain consistent nitrogen pressure for purging. | Whole series with nitrogen purging |
| La tubería de suministro de nitrógeno debe ser de PVC limpio y flexible o equivalente, con 6 mm (1/4 in) de diámetro interior; nunca utilice tubería de goma. p.25 ↗ | Rubber tubing may introduce talc into the optical system, causing contamination. | Whole series with nitrogen purging |
| El caudalímetro debe ser capaz de monitorizar caudales entre 0 y 30 litros por minuto (64 pies cúbicos por hora). p.26 ↗ | Select a flowmeter with adequate range for the purging system. | Whole series with nitrogen purging |
| El módulo de lámpara contiene una lámpara de destello de xenón de alta tensión que funciona a 1260 kPa. p.8 ↗ | Never disassemble the lamp module or look down the hole; risk of electric shock and eye damage. | Whole series |
| Parámetros de alineación de la lámpara: Ex. Wavelength 540 nm, Ex. Slit 1.5 nm, Ave. time 0.1 s, PMT voltage Medium. p.35 ↗ | Use these settings in the Align application when aligning the lamp module after replacement. | Whole series |
| La alineación de la lámpara requiere ajustar el tornillo inferior izquierdo (vertical) y el tornillo superior derecho (horizontal) para obtener la señal máxima con el destornillador de tuerca de 5.5 mm suministrado. p.35 ↗ | Proper alignment is essential for optimum instrument performance after lamp module replacement. | Whole series |
| El tornillo de ajuste de inclinación del soporte de celda única requiere una llave hexagonal de 2.5 mm. p.24 ↗ | Keep a 2.5 mm hex key available for cell holder alignment. | Whole series with single cell holder |
| Durante la instalación del software, la instalación de .Net Framework y del controlador GPIB puede tardar de 3 a 5 minutos y el ordenador puede parecer bloqueado. p.27 ↗ | Do not exit the installation during this period; wait for completion. | Cary Eclipse WinFLR software |
| El instrumento pesa más de 30 kg (66 lb); utilice dos o más personas para levantarlo o transportarlo. p.21 ↗ | Plan for safe handling during installation or relocation to avoid injury or equipment damage. | Whole series |
| El Cary Eclipse está clasificado como Equipment Class I y requiere una conexión a tierra integral entre la base metálica y la toma de tres clavijas con toma de tierra. p.9 ↗ | Ensure proper grounding to avoid electric shock hazard. | Whole series |
| El instrumento es adecuado para uso en interiores únicamente, grado de contaminación 2, categoría de instalación II (EN 61010-1). p.18 ↗ | Do not install in outdoor or harsh environments; ensure the electrical installation meets Category II requirements. | Whole series |
Faults & Troubleshooting
| Code / Symptôme | Possible Cause | Remedy | Note |
|---|---|---|---|
| Instrument offline p.42 ↗ | Computer not restarted after software installation; main instrument cable (USB-GPIB-HS) not properly connected; instrument initialization not completed before starting software. | Restart the computer after installing Cary Eclipse WinFLR software; check the connection of the USB-GPIB-HS cable; ensure the instrument has completed initialization tests before starting the software; contact local Agilent office if problem persists. | |
| Connect button instead of Start p.42 ↗ | Another Cary application is running and may have control of the instrument. | Check for other Cary applications running; if they are not collecting data, click the 'Connect' button to get control of the instrument. | |
| Instrument performance tests do not meet specifications p.43 ↗ | Sample compartment not empty; cable connecting instrument to computer not correctly connected or retaining screws not tightened; lamp not pulsing during initialization (indicated by green power indicator not flashing); lamp not correctly aligned; possible hardware conflict. | Ensure sample compartment is empty; check cable connection and tighten retaining screws; verify lamp is pulsing (green power indicator flashing, audible lamp and monochromator/filter wheel movement); align the lamp module as described in Chapter 4; if lamp is not pulsing, check for hardware conflict. | Chapter 4 for lamp alignment |
Technical Data
| Parameter | Value | Condition |
|---|---|---|
| Non-operating (transport) altitude | 0–2133 m p.18 ↗ | Non-operating (transport) |
| Non-operating (transport) altitude | 0–7000 ft p.18 ↗ | Non-operating (transport) |
| Non-operating (transport) temperature | 5–45 °C p.18 ↗ | Non-operating (transport) |
| Non-operating (transport) temperature | 41–113 °F p.18 ↗ | Non-operating (transport) |
| Non-operating (transport) relative humidity, non-condensing | 20–80 % p.18 ↗ | Non-operating (transport) |
| Operating altitude within performance specifications | 0–853 m p.18 ↗ | Operating within performance specifications |
| Operating altitude within performance specifications | 0–2800 ft p.18 ↗ | Operating within performance specifications |
| Operating altitude within performance specifications | 853–2133 m p.18 ↗ | Operating within performance specifications |
| Operating altitude within performance specifications | 2800–7000 ft p.18 ↗ | Operating within performance specifications |
| Operating temperature within performance specifications | 10–35 °C p.18 ↗ | Operating within performance specifications, 0–853 m |
| Operating temperature within performance specifications | 50–95 °F p.18 ↗ | Operating within performance specifications, 0–853 m |
| Operating temperature within performance specifications | 10–25 °C p.18 ↗ | Operating within performance specifications, 853–2133 m |
| Operating temperature within performance specifications | 50–77 °F p.18 ↗ | Operating within performance specifications, 853–2133 m |
| Operating relative humidity, non-condensing | 8–80 % p.18 ↗ | Operating within performance specifications |
| Weight, packed | 54 kg p.19 ↗ | Packed |
| Weight, packed | 119 lb p.19 ↗ | Packed |
| Weight, unpacked | 31 kg p.19 ↗ | Unpacked |
| Weight, unpacked | 68 lb p.19 ↗ | Unpacked |
| Dimensions (width x depth x height), packed | 820 x 760 x 560 mm p.19 ↗ | Packed |
| Dimensions (width x depth x height), packed | 32 x 30 x 22 in p.19 ↗ | Packed |
| Dimensions (width x depth x height), unpacked | 600 x 610 x 280 mm p.19 ↗ | Unpacked |
| Dimensions (width x depth x height), unpacked | 24 x 24 x 11 in p.19 ↗ | Unpacked |
| Voltage | 100–240 VAC p.19 ↗ | |
| Frequency | 50–60 Hz p.19 ↗ | |
| Consumption | 180 VA p.19 ↗ | approximately |
| Mains inlet coupler | 3/2 A 120/250 VAC 50–60 Hz IEC type p.19 ↗ | |
| Fuse | T3.15 AH 250 V (5 x 20 mm) IEC127 Sheet 5 p.20 ↗ | |
| Nitrogen supply pressure | 70 kPa p.20 ↗ | |
| Nitrogen supply pressure | 10 psi p.20 ↗ |