Operating Instructions — VGD 4 vacuum pump (BA 234-EN, ed. 1.6 3.12.2019, EN)
Technical Reference Summary
Covered Models & Document Scope
Couvre les pompes à vide à palettes rotatives à joint d'huile V-VGD 4, V-VGD 8, V-VGD 11, V-VGD 16 et V-VGD 21 (série V, édition 1.6, BA 234-EN). Les variantes diffèrent par la capacité d'aspiration, le vide limite, le type/viscosité de l'huile (ISO VG 32 pour V-VGD 4–16, ISO VG 46 pour V-VGD 21), le clapet de ballast à gaz (V-VGD 16 et 21 uniquement) et le montage (V-VGD 4 non vissée à la surface d'appui).
Section-by-Section Technical Breakdown
Décrit la construction et le principe de fonctionnement de la série V-VGD. Les pompes comportent un filtre à maille fine côté aspiration et un séparateur huile/brouillard d'huile côté refoulement renvoyant l'huile dans la circulation. Le moteur et la pompe partagent un arbre commun ; un clapet anti-retour intégré empêche la ventilation du système mis sous vide après l'arrêt.
- Fine mesh filter on suction side; oil and oil mist separator on outlet side
- Motor fan cools motor and pump housing; motor and pump have common shaft
- Integral non-return valve prevents evacuated system from being ventilated after pump stop
- If machine has been idle for more than two minutes, connected pipe should be ventilated to atmospheric pressure
- Gas ballast valve (V-VGD 16 and 21) prevents water vapour condensation inside the pump at operating temperature
Définit l'usage prévu et les limites de fonctionnement des pompes. La capacité d'aspiration à 50 Hz est de 4, 8, 10, 15 et 20 m³/h pour les V-VGD 4, 8, 11, 16 et 21 respectivement. Les pompes conviennent à la mise sous vide de systèmes fermés mais pas au fonctionnement continu ; les limites d'intervalle de commutation et le volume maximal mis sous vide sont spécifiés.
- Suction capacity with unrestricted suction at 50 Hz: 4, 8, 10, 15, 20 m³/h (V-VGD 4, 8, 11, 16, 21)
- Not suitable for continuous operation
- Switching interval may not exceed 12 times per hour (start/stop) at 2–100 mbar (abs.) for V-VGD 4, 8, 11, 16 and 1.5–100 mbar (abs.) for V-VGD 21
- Volume to be evacuated must be no more than 2 % of nominal suction capacity
- If installed in open air, unit must be protected from environmental influences (e.g. protective roof)
Couvre la préparation, l'installation mécanique, le raccordement des tuyauteries, le remplissage d'huile et le raccordement du moteur. La machine doit être installée horizontalement (inclinaison max. 10° dans toutes les directions) et vissée à la surface d'appui (pas pour VGD 4). L'installation électrique doit être réalisée par un électricien qualifié conformément à EN 60204.
- Machine may only be operated when set up horizontally (max. inclination 10° in all directions)
- Machine must be screwed to bearing surface to secure against tipping and slipping (not for VGD 4)
- Bearing surface must be plane, even, able to carry weight, and at least same size as machine
- Output reduction noticeable when installed at more than 1000 m above sea level
- Counter pressures on outlet side only permissible up to +0.1 bar
- Only screw in pipes by hand; use flexible connections if necessary
- Fill lubricating oil between max. and min. mark on oil sight glass
- Motor protection switch required; connecting cable installed via cable fitting for strain relief
- Permissible tolerances: ±5 % voltage deviation, ±2 % frequency deviation
- Motors comply with DIN EN 60034, protection class IP 54, insulation class B
Décrit les contrôles de mise en service, la vérification du sens de rotation, la mise hors service/stockage et la remise en service. La température ambiante de fonctionnement est de 10–40 °C et l'humidité doit être inférieure à 85 %. Le sens de rotation doit être vérifié avec un indicateur de séquence de phases ; le ventilateur du moteur doit tourner dans le sens antihoraire vu depuis le ventilateur.
- Operating ambient temperature 10–40 °C; humidity less than 85 %
- Use phase sequence indicator to check clockwise rotating field
- Start motor briefly (max. two seconds) to check direction; when looking at motor fan, it must rotate anti-clockwise
- After correcting rotation direction, run motor for 2 minutes then top up oil to upper edge of sight glass; filling point must not be open when pump is running
- Decommissioning: switch off, close cut-off devices, disconnect from electricity, depressurise, remove pipes, seal connections with adhesive foil
- Re-commissioning: check condition, drain preserving agents
Spécifie les intervalles de maintenance et les procédures pour le filtrage de l'air, la lubrification et le remplacement de l'élément séparateur d'huile. Une maintenance régulière est nécessaire pour garantir la sécurité de fonctionnement. L'ensemble de l'unité doit toujours être maintenu propre.
- Monthly: check pipes and screws for leaks, check terminal box and cable inlet holes for leaks, clean ventilation slots and motor cooling ribs
- Clean intake air filter depending on how dirty the discharged medium is
- Daily: check oil level
- First oil change after 500 h; subsequent oil changes every 1,500–3,000 h
- Change oil separator element every 1,500–3,000 operating hours
- Oil viscosity must comply with ISO VG 32 (V-VGD 4–16) or ISO VG 46 (V-VGD 21) as per DIN ISO 3448
- Recommended oils: SUPER-LUBE 32 for V-VGD 4–16, SUPER-LUBE 46 for V-VGD 21
- Always change oil when machine is at operating temperature and in an atmospherically ventilated area
- If changing oil type, empty oil removing device housing and oil cooler completely
- Oil separator element cannot be cleaned; replace every 1,500–3,000 operating hours
- Lightly oil O-ring on new oil separator element before fitting
Fournit le niveau de pression acoustique, le poids, les dimensions, le vide limite, la taille du raccordement au vide et la quantité d'huile correcte pour chaque modèle. Les valeurs sont données pour un fonctionnement à 50 Hz ; la longueur et le poids peuvent différer selon la conception du moteur.
- Sound pressure level (max.) at 50 Hz: 58 dB(A) V-VGD 4, 62 dB(A) V-VGD 8 and 11, 65 dB(A) V-VGD 16 and 21 (tolerance ±3 dB(A), EN ISO 3744)
- Weight: 5.8 kg (V-VGD 4), 11.5 kg (V-VGD 8 and 11), 16 kg (V-VGD 16), 19.5 kg (V-VGD 21)
- Ultimate vacuum: 2 mbar (abs.) for V-VGD 4, 8, 11, 16; 1.5 mbar (abs.) for V-VGD 21
- Vacuum connection: Ø 13 mm (V-VGD 4), Ø 20 mm (V-VGD 8, 11, 16, 21)
- Correct amount of oil: 0.13 l (V-VGD 4), 0.25 l (V-VGD 8 and 11), 0.45 l (V-VGD 16 and 21)
Key Integration, Operating & Safety Requirements
| Specification / Condition | Engineering Implication | S'applique à |
|---|---|---|
| La capacité d'aspiration avec aspiration non restreinte à 50 Hz est de 4 m³/h (V-VGD 4), 8 m³/h (V-VGD 8), 10 m³/h (V-VGD 11), 15 m³/h (V-VGD 16) et 20 m³/h (V-VGD 21). p.16 ↗ | Used for sizing the pump to the required evacuation flow; note that actual capacity is reduced by narrow or long inlet pipes. | V-VGD 4, 8, 11, 16, 21 |
| L'intervalle de commutation ne doit pas dépasser 12 fois par heure (marche/arrêt) dans une plage de pression de 2–100 mbar (abs.) pour V-VGD 4, 8, 11 et 16 et de 1.5–100 mbar (abs.) pour V-VGD 21. p.16 ↗ | Frequent cycling outside these ranges risks oil leaking through the outlet opening and exceeding motor winding/bearing temperature limits. | V-VGD 4, 8, 11, 16, 21 |
| Lors de la mise sous vide de systèmes fermés, le volume à mettre sous vide ne doit pas dépasser 2 % de la capacité d'aspiration nominale de la pompe à vide. p.16 ↗ | Limits the allowable connected volume for intermittent evacuation; larger volumes require a larger pump or different operating mode. | V-VGD 4, 8, 11, 16, 21 |
| La machine ne doit être utilisée qu'à une température ambiante et une température d'aspiration comprises entre 10 et 40 °C. p.7 ↗ | Installation location and process gas temperature must be controlled within this range; contact manufacturer for temperatures outside this range. | V-VGD 4, 8, 11, 16, 21 |
| Les contre-pressions côté refoulement ne sont admissibles que jusqu'à +0.1 bar. p.18 ↗ | Exhaust lines must be sized and routed to avoid back pressure exceeding 0.1 bar; never close or constrict exhaust air openings. | V-VGD 4, 8, 11, 16, 21 |
| La tolérance de tension admissible est de ±5 % et la tolérance de fréquence de ±2 %. p.19 ↗ | Mains supply must be within these tolerances of the motor data plate values to avoid loss of power or damage. | V-VGD 4, 8, 11, 16, 21 |
| Les moteurs sont conformes à DIN EN 60034, classe de protection IP 54 et classe d'isolation B. p.19 ↗ | Electrical installation must be suitable for IP 54 environment; motor protection switch required and connecting cable installed via cable fitting for strain relief. | V-VGD 4, 8, 11, 16, 21 |
| Première vidange d'huile après 500 heures de fonctionnement ; vidanges suivantes après 1,500–3,000 heures de fonctionnement. p.24 ↗ | Maintenance schedule must include initial 500 h oil change and recurring 1,500–3,000 h changes; reduce intervals depending on contamination of discharged medium. | V-VGD 4, 8, 11, 16, 21 |
| L'élément séparateur d'huile doit être remplacé toutes les 1,500–3,000 heures de fonctionnement ; il ne peut pas être nettoyé. p.25 ↗ | Plan spare part replacement at these intervals; contaminated element increases power consumption and pump temperature and may cause oil ignition in extreme cases. | V-VGD 4, 8, 11, 16, 21 |
| La viscosité de l'huile doit être conforme à ISO VG 32 (V-VGD 4–16) ou ISO VG 46 (V-VGD 21) selon DIN ISO 3448. p.24 ↗ | Use only oil of correct viscosity; recommended Elmo Rietschle oils are SUPER-LUBE 32 for V-VGD 4–16 and SUPER-LUBE 46 for V-VGD 21. | V-VGD 4, 8, 11, 16, 21 |
| Quantité d'huile correcte : 0.13 l (V-VGD 4), 0.25 l (V-VGD 8 et 11), 0.45 l (V-VGD 16 et 21). p.30 ↗ | Oil fill quantity for initial fill and refill; oil level must always be visible between max. and min. mark on sight glass. | V-VGD 4, 8, 11, 16, 21 |
| Vide limite : 2 mbar (abs.) pour V-VGD 4, 8, 11, 16 ; 1.5 mbar (abs.) pour V-VGD 21. p.30 ↗ | Defines the maximum vacuum achievable with suction opening closed; selection must consider required final pressure. | V-VGD 4, 8, 11, 16, 21 |
| Raccordement au vide : Ø 13 mm (V-VGD 4), Ø 20 mm (V-VGD 8, 11, 16, 21). p.30 ↗ | Pipework and fittings must match these connection sizes; undersized inlet pipe reduces pumping capacity. | V-VGD 4, 8, 11, 16, 21 |
| Niveau de pression acoustique (max.) à 50 Hz : 58 dB(A) V-VGD 4, 62 dB(A) V-VGD 8 et 11, 65 dB(A) V-VGD 16 et 21 (tolérance ±3 dB(A), EN ISO 3744). p.30 ↗ | Use ear protection when spending long time near running machine; consider acoustic measures for noise-sensitive installations. | V-VGD 4, 8, 11, 16, 21 |
| La machine ne peut être utilisée que si elle est installée horizontalement avec une inclinaison max. de 10° dans toutes les directions. p.17 ↗ | Mounting surface must be plane and even; machine must be screwed to bearing surface (not for VGD 4) to secure against tipping and slipping. | V-VGD 4, 8, 11, 16, 21 |
| Une réduction de puissance est perceptible en cas d'installation à plus de 1000 m au-dessus du niveau de la mer. p.17 ↗ | For high-altitude installations, contact manufacturer for suitability and possible derating. | V-VGD 4, 8, 11, 16, 21 |
| Plage de température de stockage : -10 °C à +60 °C ; humidité relative 0 % à 80 %. p.11 ↗ | Storage area must meet these conditions; for long-term storage (more than 3 months) use preservation oil rather than operating oil. | V-VGD 4, 8, 11, 16, 21 |
| Si la machine est restée inactive pendant plus de deux minutes, la tuyauterie raccordée doit être mise à l'air libre à la pression atmosphérique. p.16 ↗ | Prevents oil from being drawn into the evacuated system due to vacuum remaining in the pipe after pump stop. | V-VGD 4, 8, 11, 16, 21 |
| Le clapet de ballast à gaz est présent uniquement sur V-VGD 16 et V-VGD 21. p.16 ↗ | For processes with water vapour, select V-VGD 16 or 21; gas ballast prevents condensation inside the pump when low amounts of steam are sucked in at operating temperature. | V-VGD 16, V-VGD 21 |
Faults & Troubleshooting
| Code / Symptôme | Possible Cause | Remedy | Note |
|---|---|---|---|
| Machine is switched off by the motor protection switch p.27 ↗ | Mains voltage/ Frequency does not correspond with the motor data | Check by qualified electrician | Section 5.5 |
| Machine is switched off by the motor protection switch p.27 ↗ | Connection to motor terminal board is not correct | Check by qualified electrician | Section 5.5 |
| Machine is switched off by the motor protection switch p.27 ↗ | Motor protection switch is not set correctly | Check by qualified electrician | Section 5.5 |
| Machine is switched off by the motor protection switch p.27 ↗ | Motor protection switch is triggered too quickly | Use a motor protection switch with an overload-dependent delayed switch off that takes into consideration the short term excess current at start up (version with short circuit and overload trigger as per IEC 60947-4-1 or VDE 0660 Part 102) | |
| Machine is switched off by the motor protection switch p.27 ↗ | Vacuum pump or its oil is too cold | Note the ambient temperature and the intake temperature | Section 2.3 |
| Machine is switched off by the motor protection switch p.27 ↗ | The lubricating oil is too viscous | The oil viscosity must comply with ISO VG 32 / 46 (see pump type) as per DIN ISO 3448 | Section 7.2.2 |
| Machine is switched off by the motor protection switch p.27 ↗ | The oil separator element is dirty. | Change the oil separator element | Section 7.2.3 |
| Machine is switched off by the motor protection switch p.27 ↗ | The back pressure is too high when the exhaust air is being discharged. | Check the hose or the pipe | Section 5.3 |
| Suction capacity is insufficient p.27 ↗ | The suction pipe is too long or too narrow | Check the hose or the pipe | Section 5.3 |
| Suction capacity is insufficient p.27 ↗ | Leak on the suction side of the vacuum pump or in the system | Check the pipework and screw connections for leaks and to ensure that they are firmly seated. | Section 7.2 |
| Suction capacity is insufficient p.27 ↗ | The intake filter is dirty | Clean or replace the intake filter | Section 7.2.1 |
| Final pressure (max. vacuum) is not reached p.27 ↗ | Leak on the suction side of the vacuum pump or in the system | Check the pipework and screw connections for leaks and to ensure that they are firmly seated. | Section 7.2 |
| Final pressure (max. vacuum) is not reached p.27 ↗ | Incorrect oil viscosity | The oil viscosity must comply with ISO VG 32 / 46 (see pump type) as per DIN ISO 3448 | Section 7.2.2 |
| Machine gets too hot p.28 ↗ | Ambient or intake temperature is too high | Ensure it is being used properly | Section 2.3 |
| Machine gets too hot p.28 ↗ | Cooling air supply is obstructed | Check environmental conditions | Section 5.1 |
| Machine gets too hot p.28 ↗ | Cooling air supply is obstructed | Clean ventilation slots | Section 7.2 |
| Machine gets too hot p.28 ↗ | The lubricating oil is too viscous | The oil viscosity must comply with ISO VG 32 / 46 (see pump type) as per DIN ISO 3448 | Section 7.2.2 |
| Machine gets too hot p.28 ↗ | The oil separator element is dirty. | Change the oil separator element | Section 7.2.3 |
| Machine gets too hot p.28 ↗ | The back pressure is too high when the exhaust air is being discharged. | Check the hose or the pipe | Section 5.3 |
| Exhaust air contains visible oil mist p.28 ↗ | The oil separator element is not inserted correctly or the O ring is missing | Check that it is correctly seated | Section 7.2.3 |
| Exhaust air contains visible oil mist p.28 ↗ | Unsuitable oil is being used | Use suitable types | Section 7.2.2 |
| Exhaust air contains visible oil mist p.28 ↗ | The oil separator element is dirty. | Change the oil separator element | Section 7.2.3 |
| Exhaust air contains visible oil mist p.28 ↗ | Ambient or intake temperature is too high | Ensure it is being used properly | Section 2.3 |
| Exhaust air contains visible oil mist p.28 ↗ | Cooling air supply is obstructed | Check environmental conditions | Section 5.1 |
| Exhaust air contains visible oil mist p.28 ↗ | Cooling air supply is obstructed | Clean ventilation slots | Section 7.2 |
| The machine makes a abnormal noise (The blades making a hammering noise when starting from cold is normal if it disappears within two minutes as the operating t p.29 ↗ | The pump housing is worn (chatter marks) | Repair by manufacturer or authorised workshop | Elmo Rietschle Service |
| The machine makes a abnormal noise (The blades making a hammering noise when starting from cold is normal if it disappears within two minutes as the operating t p.29 ↗ | Blades are damaged | Repair by manufacturer or authorised workshop | Elmo Rietschle Service |
| The machine makes a abnormal noise (The blades making a hammering noise when starting from cold is normal if it disappears within two minutes as the operating t p.29 ↗ | Vacuum pump or its oil is too cold | Note the ambient temperature and the intake temperature | Section 2.3 |
| The machine makes a abnormal noise (The blades making a hammering noise when starting from cold is normal if it disappears within two minutes as the operating t p.29 ↗ | The lubricating oil is too viscous | The oil viscosity must comply with ISO VG 32 / 46 (see pump type) as per DIN ISO 3448 | Section 7.2.2 |
| Water in lubricating oil p.29 ↗ | Pump sucks in water | Install water interceptor upstream of the pump | |
| Water in lubricating oil p.29 ↗ | The pump sucks in more water vapour than is suitable for its water vapour compatibility | Contact the manufacturer for increased gas ballast | |
| Water in lubricating oil p.29 ↗ | Pump only works for a short time and therefore does not reach its normal operating temperature | Let the pump continue to run with a closed suction side after extracting the water vapour until the water has evaporated from the oil |