Induztr
Résumé technique Visionneuse de documents Modèles associés

Minichiller 800-H Datasheet

Sommaire

  1. Overview p. 1
    Introduces the Minichiller 800-H unit and its main features
  2. Spec pp. 1-2
    Performance, temperature, and physical data per DIN 12876
  3. p. 2 table, 6 rows
  4. p. 1 table, 34 rows

Technical data according to DIN 12876

ParameterValue
Fuse16 A
Pressure equipment categoryArt. 4.3 PED
Degree of ProtectionIP20
min. ambient temperature5 °C
max. ambient temperature40 °C
from Serial-No.:S623474

Minichiller 800-H — Technical data according to DIN 12876

ParameterValue
Order-No.3079.0010.01
Operating temperature range-20...100 °C
temperature set point / display5,7" colour Touchscreen
Internal temperature sensorPt100
Sensor external connectionPt100
Temperature stability at -10°C0,2 K
Interface digitalEthernet, USB (Host u. Device), RS232
Safety classificationIII / FL
Heating power at 240V2,1 kW
Heating power at 230V2 kW
Heating power at 220V1,8 kW
Heating power at 208V1,6 kW
Cooling power at ambient temperature +20°C
at 15°C0,8 kW
at 0°C0,6 kW
at -10°C0,45 kW
at -20°C0,3 kW
Refrigeration machineair-cooled, natural refrigerant
Refrigerant (ASHRAE, GHS)R-290 (A3, H220)
Global Warming Potential (GWP)0,02
Refrigerant quantity0,099 kg
CO2 equivalent0,0 t
Circulation pump:Pressure- and suction pump
max. delivery24 l/min
max. delivery pressure0,7 bar
max. delivery (suction)18 l/min
max. delivery pressure (suction)0,4 bar
Pump connectionM16x1 male
min. filling capacity2,8 l
Volume of expansion2,2 l
Overall dimensions WxDxH **280x490x424 mm
Net weight39 kg
Power supply requirement208-240V 1~/2~ 50/60Hz
max. current12 A

** Overall dimensions WxDxH — как напечатано в исходном тексте.

Engineering Facts

12 facts · every claim linked to a page
Selection

The unit uses R-290 (A3, H220) refrigerant, which is flammable, so the installation location must be assessed for A3 refrigerant safety requirements.

Flammable A3 refrigerant affects room ventilation, ignition-source control, and local safety compliance during selection and installation.

Source
“Refrigerant (ASHRAE, GHS) R-290 (A3, H220)”
Installation

The chiller is air-cooled, so sufficient clearance and airflow must be provided around the unit to avoid reduced cooling capacity.

Air-cooled condensers require unobstructed airflow; poor clearance will degrade performance and may cause overheating.

Source
“Chiller with air-cooled refrigerating unit and circulation pump.”
Installation

The power supply must be 208-240 V single-phase or two-phase at 50/60 Hz with a maximum current of 12 A and a 16 A fuse.

Electrical supply, breaker sizing, and cabling must match this requirement before installation.

Source
“Power supply requirement 208-240V 1~/2~ 50/60Hz”
Installation

Voltage and frequency tolerances are ±5% and ±2% respectively, but a -5% voltage combined with +2% frequency is not allowed.

Supply quality must be verified; certain combined tolerances can damage the compressor or electronics.

Source
“-5% voltage and +2% frequency -> not allowed!”
Operation

The ambient temperature must stay between 5 °C and 40 °C, and cooling capacity may drop if ambient temperature rises above 20 °C.

Installation room temperature directly affects available cooling power and must be considered in the thermal design.

Source
“If the ambient temperature rises, the cooling capacity may drop.”
Operation

The plastic pump is not resistant to acetone or polyglycols, so water mixed with glysantine or ethylene glycol should be used for freeze protection.

Fluid compatibility must be checked before commissioning to avoid pump damage and leaks.

Source
“The plastic pump is not resistant against acetone and polyglycols (depending on the manufacturer).”
Installation

Single- and two-phase devices are delivered with a power cable and country-specific plug, which must be specified at ordering.

The correct plug type must be ordered to avoid delays and rework during installation.

Source
“Single / two-phase devices (100V to 240V) --> with power cable and country-specific plug (please specify when ordering)”
Conformité

The equipment is classified as EN55011 Class A, Group 1, so it is intended for industrial electromagnetic environments and may cause interference in residential areas.

Class A equipment has EMC restrictions and may require additional filtering or separation from sensitive electronics.

Source
“Classification (disturbance) to EN55011: Class A, Group 1”
Safety

The unit has IP20 protection, so it must be installed in a dry indoor location protected from water and dust ingress.

IP20 is not suitable for wet or dusty environments; installation location must match the enclosure rating.

Source
“Degree of Protection IP20”
Selection

The minimum filling capacity is 2.8 l and the expansion volume is 2.2 l, which determines the minimum circuit volume and expansion vessel sizing.

External circuit volume and expansion vessel must be sized to avoid overflow or pump cavitation.

Source
“min. filling capacity 2,8 l”
Performance

Cooling capacity drops from 0.8 kW at +15 °C to 0.3 kW at -20 °C, so the required heat load must be checked at the actual operating temperature.

Selecting the chiller only by nominal capacity can lead to insufficient cooling at low temperatures.

Source
“at -20°C 0,3 kW”
Installation

The pump connection is M16x1 male, and hose connection NW12 and sleeve nuts M16x1 are included as accessories.

External piping and hoses must match the M16x1 thread to ensure leak-free connection.

Source
“Pump connection M16x1 male”