Induztr
Résumé technique Visionneuse de documents Modèles associés

IMG-300 Inverted Magnetron Gauge

Sommaire

  1. Overview pp. 9-10
    Introduces the IMG-300 inverted magnetron gauge and its principle
  2. Warning p. 11
    Electromagnetic compatibility warnings and compliance notes
  3. Overview pp. 13-18
    Describes general purpose inverted magnetron gauge details
  4. Spec pp. 15-19
    Technical specifications and requirements tables for the gauge
  5. Ordering pp. 19-20
    Ordering codes and configuration options for gauge variants
  6. pp. 20-24
    Vacuum Products Division contact and company information
  7. p. 15 table, 9 rows
  8. p. 20 table, 40 rows

Table 1-1 IMG-300 Technical Specifications

SpecificationDefinition
Operating voltage (HV range)3 kV DC
Sensitivity2.5 A/Torr + 100%; -5% @ 5x 10−6 Torr
Measurement Range10-3 to 10-11 Torr
Maximum Operating Temperature250 °C, CFF metal gasket; with magnet
Electrical ConnectorSHV style, 5kV rated
Feedthrough/UHVCeramic brazed
Ignition Time< 5 seconds at pressures > 1E-6 Torr, typically 20 min @ 1E-10 Torr
Response Time< 10 milliseconds for increasing pressure
Material Exposed to the Vacuum304L Stainless steel, Nickel, 2% Thoriated Tungsten, and ceramic

Request for Return Form (Health and Safety Certification)

SectionFieldValue
1) CUSTOMER INFORMATIONCompany Name
1) CUSTOMER INFORMATIONContact Name
1) CUSTOMER INFORMATIONTel
1) CUSTOMER INFORMATIONEmail
1) CUSTOMER INFORMATIONFax
1) CUSTOMER INFORMATIONCustomer Ship To
1) CUSTOMER INFORMATIONCustomer Bill To
1) CUSTOMER INFORMATIONEurope only: VAT reg. Number
1) CUSTOMER INFORMATIONUSA/Canada only: Taxable
1) CUSTOMER INFORMATIONUSA/Canada only: Non-taxable
2) PRODUCT IDENTIFICATIONProduct Description
2) PRODUCT IDENTIFICATIONAgilent P/N
2) PRODUCT IDENTIFICATIONAgilent S/N
2) PRODUCT IDENTIFICATIONOriginal Purchasing Reference
3) TYPE OF RETURN3A. Non-Billable
3) TYPE OF RETURN3A. Billable
3) TYPE OF RETURN3A. New PO # (hard copy must be submitted with this form)
3) TYPE OF RETURN3B. Exchange
3) TYPE OF RETURN3B. Repair
3) TYPE OF RETURN3B. Upgrade
3) TYPE OF RETURN3B. Consignment/Demo
3) TYPE OF RETURN3B. Calibration
3) TYPE OF RETURN3B. Evaluation
3) TYPE OF RETURN3B. Return for Credit
4) HEALTH and SAFETY CERTIFICATIONHAS NOT pumped or been exposed to any toxic or hazardous materials
4) HEALTH and SAFETY CERTIFICATIONHAS pumped or been exposed to the following toxic or hazardous materials
4) HEALTH and SAFETY CERTIFICATIONToxic
4) HEALTH and SAFETY CERTIFICATIONCorrosive
4) HEALTH and SAFETY CERTIFICATIONReactive
4) HEALTH and SAFETY CERTIFICATIONFlammable
4) HEALTH and SAFETY CERTIFICATIONExplosive
4) HEALTH and Safety CertificationBiological
4) HEALTH and Safety CertificationRadioactive
4) HEALTH and Safety CertificationList all toxic/hazardous materials. Include product name, chemical name, and chemical symbol or formula
4) HEALTH and Safety CertificationPrint Name
4) HEALTH and Safety CertificationAuthorized Signature
4) HEALTH and Safety CertificationDate
5) FAILURE INFORMATIONFailure Mode (REQUIRED FIELD. See next page for suggestions of failure terms)
5) FAILURE INFORMATIONDetailed Description of Malfunction: (Please provide the error message)
5) FAILURE INFORMATIONApplication (system and model)

Форма содержит чекбоксы и поля для заполнения; пустые ячейки оставлены пустыми строками.

Engineering Facts

14 facts · every claim linked to a page
Safety

The controller and vacuum system must be separately connected to a common ground, and a ground wire must not be placed between the vacuum chamber and controller chassis.

Improper grounding can create large circulating currents and lethal high-voltage hazards, so grounding must be verified before operation.

Source
“Do not place a ground wire between the vacuum chamber and the controller chassis; large continuous currents could flow through it.”
Safety

The system ground must be tested to confirm it is complete and can support at least 10 A.

A verified low-impedance ground is required to safely handle the 3 kV high voltage present in the gauge.

Source
“Test the system ground to be sure that it is complete and capable of supporting at least 10 A.”
Safety

The gauge is not intrinsically safe and must never be turned on when combustible gases or mixtures are present.

The high-voltage discharge and filament/grid can act as ignition sources, so the gauge must be isolated from combustible atmospheres.

Source
“As with all ionization gauges, this device is not intrinsically safe.”
Installation

The IMG-300 must not be mounted closer than a few inches to any magnetic material because the magnet generates an external field.

Magnetic material near the gauge distorts the field and can change calibration and starting behavior.

Source
“Do not mount the IMG-300 closer than a few inches to any magnetic material.”
Installation

Rough handling or prolonged contact with the metal surface can weaken the magnet and shift calibration.

Mechanical abuse of the magnet assembly degrades measurement accuracy, so careful mounting and handling are required.

Source
“Avoid rough handling or prolonged contact with the metal surface which can cause a decrease in magnet strength and result in a calibration change.”
Operation

The gauge can be baked out at up to 250 °C with the cable unplugged.

Bakeout capability determines UHV compatibility, but the cable must be disconnected to avoid damage during bakeout.

Source
“The IMG-300 with CFF handles bakeout temperatures of up to 250 °C, with the cable unplugged.”
Performance

The gauge covers the pressure range from 10-3 Torr down to 10-11 Torr.

The measurement range must match the application's operating pressure to select the correct gauge.

Source
“measures vacuum pressure from 10-3 Torr (10-3 mbar) down to 10-11 Torr (10-11 mbar).”
Performance

Ignition time is under 5 seconds above 1E-6 Torr but typically about 20 minutes at 1E-10 Torr.

Slow starting at high vacuum affects process timing and may require patience or starting aids in UHV applications.

Source
“Ignition Time < 5 seconds at pressures > 1E-6 Torr, typically 20 min @ 1E-10 Torr”
Performance

The response time is under 10 milliseconds for increasing pressure.

Fast response is important for leak detection and rapid pressure-change monitoring.

Source
“Response Time < 10 milliseconds for increasing pressure”
Selection

The gauge uses a standard SHV connector rated to 5 kV and a coaxial cable for connection to a Multi-Gauge.

The connector type and 5 kV rating must match the controller cable and high-voltage supply.

Source
“A standard SHV connector and coaxial cable provides for a safe, easy connection to a Multi-Gauge.”
Selection

All materials exposed to vacuum are high-vacuum compatible and no elastomers are used in construction.

Elastomer-free all-metal construction reduces outgassing and is suitable for UHV applications.

Source
“All materials exposed to the vacuum system are high vacuum compatible. No elastomers are used in IMG-300 construction.”
Maintenance

Silicone oil and silicone grease must not be used when servicing the vacuum equipment.

Silicone contamination migrates and degrades vacuum performance, so only approved lubricants may be used.

Source
“Do not use silicone oil or silicone grease.”
Maintenance

Alconox is incompatible with aluminum and must not be used to clean aluminum parts.

Using the wrong cleaning agent can corrode aluminum components and introduce contamination.

Source
“Do not clean any aluminum parts with Alconox. AIconox is not compatible with aluminum and will cause damage.”
Conformité

The product is Class A equipment and may cause radio interference in domestic environments.

Class A rating means the gauge is intended for commercial/industrial use, not residential, and EMC measures may be needed.

Source
“This is a Class A product. In a domestic environment this product may cause radio interference.”