Rev v xpert rxpert filtered balance systems stations
Technical Reference Summary
Covered Models & Document Scope
Couvre le système de balance filtrée Labconco XPert® Filtered Balance System, la station de balance filtrée XPert® Filtered Balance Station et le système de balance filtrée RXPert™ Filtered Balance System dans les largeurs 2', 3', 4', 5' et 6', avec des ouvertures de guillotine de 9.4" ou 12", des modèles électriques 115V ou 230V, une filtration HEPA simple ou double, et des filtres à charbon en option Odor Control (vapeurs organiques, formaldéhyde, ammoniac/amines, acide-soufre) et des raccordements d'évacuation en hotte Canopy Exhaust Connections. Les séries de modèles XPert Station 3940200, 3940300, 3940400, 3946500 et 3946600 sont identifiées.
Section-by-Section Technical Breakdown
Définit le débit d'air, le volume d'évacuation, la perte de pression statique, le bruit et la pression statique externe maximale pour chaque largeur d'enceinte et ouverture de guillotine à 60, 80 et 100 fpm. Les XPert Systems utilisent une turbine motorisée intégrée et peuvent recirculer ou être évacués vers l'extérieur via un raccordement d'évacuation en hotte Canopy Exhaust Connection et un ventilateur distant ; les XPert Stations n'ont pas de turbine intégrée et doivent être évacuées par un ventilateur distant.
- 2' 9.4" sash: 60/80/100 fpm correspond to 85/115/145 CFM, static loss .35-.41/.48-.57/.62-.72 in w.g., noise 48-53/50-56/53-58 dBA.
- 3' 9.4" sash: 60/80/100 fpm correspond to 130/175/220 CFM, static loss .37-.43/.53-.62/.68-.79 in w.g., noise 48-53/53-57/58-61 dBA.
- 4' 9.4" sash: 60/80/100 fpm correspond to 175/235/295 CFM, static loss .40-.46/.57-.66/.76-.87 in w.g., noise 49-54/58-61/62-66 dBA.
- 4' 12" sash (tall/deep): 60/80/100 fpm correspond to 230/305/380 CFM, static loss .56-.65/.77-.87/.92-1.04 in w.g., noise 58-61/62-66/67-70 dBA.
- 5' 12" sash (10" duct): 60/80/100 fpm correspond to 290/385/480 CFM, static loss .38-.46/.55-.67/.72-.85 in w.g., noise 52-56/58-63/63-67 dBA.
- 6' 12" sash (10" duct): 60/80/100 fpm correspond to 350/465/580 CFM, static loss .46-.56/.67-.81/.87-1.03 in w.g., noise 55-57/61-63/67-69 dBA.
- Balances typically work best between 60-90 fpm with the balance shield closed tightly.
- If connected directly to a house exhaust system, an adjustable damper (or valve) must be installed to control airflow properly.
Spécifie le raccordement électrique pour les modèles 115V et 230V et le circuit de relais du ventilateur distant pour les XPert Stations. Les XPert Systems n'ont aucune disposition pour commander un ventilateur distant ; les XPert Stations fournissent un interrupteur de ventilateur et un relais avec une charge de circuit maximale de 6 amps.
- 115V models: connect supplied power cord to IEC inlet on back of enclosure; at 50 Hz maximum airflow is reduced by 17%.
- 230V models: shipped without a plug; install plug per local codes.
- XPert Station remote blower is switched by an electrical relay via the blower switch; maximum circuit load for the relay is 6 amps.
- Only remote blower wiring is connected inside the electrical junction box; lights and airflow monitor are powered from a nearby standard duplex receptacle.
- Grounding connection shall not be made to the terminal box cover.
- Building supply for the remote blower should include overload protection (switch or circuit breaker) close to and within easy reach of the operator, marked as the disconnecting device.
Décrit la mise à niveau et la fixation de la surface de travail, le positionnement de l'enceinte et sa fixation avec quatre vis de montage et du mastic silicone RTV. La surface de travail doit être lisse, rigide, non poreuse et résistante aux produits chimiques et au moins aussi large que l'enceinte.
- Front of enclosure should be aligned within 0.3" of the front of the work surface.
- Insert supplied mounting screws in four holes, allowing a minimum of 1/8" clearance under the screw head for positioning.
- For 5' and 6' stainless work surfaces use #10-24 x 3/8" hex washer head screw, Labconco part number 1885806.
- Apply RTV silicone sealant between work surface and enclosure for additional support.
- Seal enclosure to work surface with a bead of silicone sealant to prevent spilled materials collecting under walls and to add rigidity.
Couvre les raccordements de gaines pour les XPert Stations et les raccordements d'évacuation en hotte Canopy Exhaust Connections en option pour les XPert Systems. Les Stations 2', 3' et 4' acceptent une gaine de 6" ; les Stations 5' et 6' acceptent une gaine de 10". Le poids de la gaine doit être supporté indépendamment de l'enceinte.
- 2', 3' and 4' XPert Stations: 6.06" ID exhaust connection; 5' and 6': 10.09" ID.
- Canopy Exhaust Connection part numbers: 3924400 (2'), 3924401 (3'), 3924402 (4'), 39294403 (5'), 3924404 (6').
- Canopy connection for 2', 3' and 4' is 6.09" ID / 6.19" OD for 6" nominal duct; 5' and 6' are 10.09" ID / 10.19" OD for 10" nominal duct.
- Exhaust duct material must match the enclosure, procedures and chemical applications.
- Exhaust system should be installed by a qualified HVAC contractor.
Les filtres HEPA sont expédiés installés avec le joint côté aval et sont contrôlés pour fuite chez Labconco ; un second contrôle de fuite est recommandé avant utilisation et au moins annuellement. Les filtres à charbon sont installés par gravité avec le joint vers le bas du côté évacuation du filtre HEPA et assurent uniquement le contrôle des odeurs, pas la protection contre les particules.
- HEPA filters are 99.99% efficient for 0.3-micron particles.
- HEPA part numbers: 2' 3707900, 3' 3707901, 4' 3707902, 5' 3707903 (2 ea), 6' 3707901 (2 ea).
- Organic vapor carbon: 2' 3937200, 3' 3937300, 4' 3937400, 5' 3981400 (2 ea), 6' 3937300 (2 ea).
- Formaldehyde carbon: 2' 3937201, 3' 3937301, 4' 3937401, 5' 3981401 (2 ea), 6' 3937301 (2 ea).
- Ammonia/amines carbon: 2' 3937202, 3' 3937302, 4' 3937402, 5' 3981402 (2 ea), 6' 3937302 (2 ea).
- Acid-sulfur carbon: 2' 3937203, 3' 3937303, 4' 3937403, 5' 3981403 (2 ea), 6' 3937303 (2 ea).
- Carbon filter use requires work-area concentration not exceed IDLH and exhaust not exceed TWA.
Explique le réglage du contrôle de vitesse sur les XPert Systems pour atteindre 60-100 fpm pour la pesée, et décrit la validation du débit d'air par des relevés d'anémomètre à travers l'ouverture de guillotine. Labconco rapporte les cotes de confinement ASHRAE 110-1995 et les résultats d'essais de confinement biologique NSF/ANSI 49.
- Speed control is behind the front panel; turn counterclockwise to increase face velocity and clockwise to decrease.
- Face velocity should be 60-100 fpm for weighing operations; lowest appropriate velocity gives quietest operation.
- Average face velocity readings: two rows, 6" from ends and every 12", first row 3" down from upper sash foil, second row 3" up from work surface.
- As-manufactured ASHRAE 110-1995 rating: less than 0.05 ppm at 4 lpm.
- Biological containment test at 75 fpm inflow typically 1 or fewer spores escaped per test.
- Balance stability tests were excellent at 78 fpm and 100 fpm with a five-decimal-place balance.
Couvre le fonctionnement et la programmation du moniteur de débit d'air Guardian Digital 1000, y compris l'étalonnage du point de consigne d'alarme et la mise en sourdine de l'alarme. Le moniteur déclenche une alarme lorsque le débit d'air s'écarte du point de consigne étalonné.
- Alarm can be temporarily silenced using the SILENCE ALARM or enter buttons.
- Audible disable requires a continuously present alarm condition; fluctuating flow near the set point resets the monitor.
- Calibration steps are given in Chapter 6 and in the supplied Digital 1000 Monitor Manual.
Fournit le calendrier de maintenance de routine, les critères de remplacement des HEPA, la procédure de remplacement des HEPA en sac (bag-in/bag-out), le test de fuite HEPA, le calcul de la durée de vie des filtres à charbon et leur remplacement, ainsi que le remplacement des éclairages LED, de la turbine motorisée et du contrôle de vitesse.
- HEPA filter leak test recommended before use and at least annually thereafter.
- Bag-in/bag-out HEPA filter allows safe disposal of hazardous filters.
- Carbon filter life must be calculated based on chemical loading; replace when loaded.
- Motorized impeller and speed control are replaceable items described in Chapter 6.
Un tableau problème/cause/action corrective couvrant les dysfonctionnements de confinement, de ventilateur, d'éclairage et de moniteur de débit d'air. Il liste des symptômes tels que contaminants à l'extérieur de l'enceinte, ventilateur ne fonctionnant pas, vitesse frontale faible, éclairages ne fonctionnant pas et alarmes du moniteur de débit d'air.
- Contaminants outside enclosure may be caused by improper technique, blocked baffle slots or exhaust outlet, external air disturbances, or improper face velocity.
- Blower won't operate: check power, circuit breaker/GFI, blower wiring, blower switch, motorized impeller.
- Low face velocity or poor containment: close sash, replace clogged HEPA filter or increase speed, replace loaded carbon filter.
- Lights do not work: check lamp installation and wiring, replace lamp, light switch or ballast.
- Airflow monitor malfunction: check power, cables, fuses, alarm set point and sensor airway.
Key Integration, Operating & Safety Requirements
| Specification / Condition | Engineering Implication | S'applique à |
|---|---|---|
| Les filtres HEPA ont un rendement d'au moins 99.99% pour les particules de 0.3 micron. p.5 ↗ | Suitable for hazardous particulate containment; carbon filters add odor control only and provide no particulate protection. | All XPert and RXPert models |
| La vitesse frontale pour les opérations de pesée doit être de 60-100 fpm ; les balances fonctionnent généralement au mieux entre 60-90 fpm avec le pare-vent de la balance bien fermé. p.10 ↗ | Set speed control within this range and verify with anemometer; lower end gives quieter operation. | XPert Filtered Balance System |
| Les modèles XPert Station 2', 3' et 4' nécessitent un raccordement d'évacuation de 6" (6.06" ID) ; les modèles 5' et 6' nécessitent 10" (10.09" ID). p.16 ↗ | Duct sizing and remote blower selection must match enclosure width. | XPert Filtered Balance Station |
| La charge de circuit maximale pour le relais du ventilateur distant de la XPert Station est de 6 amps. p.11 ↗ | Remote blower electrical load must not exceed 6 A on this circuit. | XPert Filtered Balance Station |
| En fonctionnement à 50 Hz, le débit d'air maximal du ventilateur est réduit de 17%. p.16 ↗ | Account for reduced airflow when sizing and setting face velocity on 50 Hz supplies. | 115V models |
| L'avant de l'enceinte doit être aligné à 0.3" près de l'avant de la surface de travail. p.13 ↗ | Critical for proper airflow entry and sealing. | All models |
| Les vis de montage doivent laisser un dégagement minimal de 1/8" sous la tête pour le positionnement de l'enceinte. p.14 ↗ | Ensures flanges can slide under screw heads during installation. | All models |
| Pour les surfaces de travail en acier inoxydable 5' et 6', utiliser une vis à tête hexagonale à rondelle #10-24 x 3/8", référence Labconco 1885806. p.14 ↗ | Correct fastener for large stainless work surfaces. | 5' and 6' models with stainless work surface |
| Maintenir l'humidité entre 45 et 60% pour maîtriser les effets électrostatiques. p.9 ↗ | Reduces weighing errors and powder attraction in the enclosure. | All models |
| Une dérive de température de 1-2°C est généralement tolérable pour les balances. p.8 ↗ | Avoid installing near heating sources or direct sunlight. | All models |
| Le test de fuite des filtres HEPA est recommandé avant utilisation et au moins annuellement par la suite. p.19 ↗ | Scheduled leak testing is required to maintain containment assurance. | All models |
| Les filtres à charbon sont installés par gravité avec le joint vers le bas du côté évacuation du filtre HEPA. p.19 ↗ | Correct orientation is essential for odor control performance. | Models with accessory carbon filter |
| L'utilisation de filtres à charbon exige que la concentration dans la zone de travail ne dépasse pas l'IDLH et que l'évacuation ne dépasse pas la TWA. p.19 ↗ | Chemical application must be reviewed by a Labconco product specialist for suitability. | Models with accessory carbon filter |
| Références des raccordements d'évacuation en hotte Canopy Exhaust Connection : 3924400 (2'), 3924401 (3'), 3924402 (4'), 39294403 (5'), 3924404 (6'). p.18 ↗ | Order correct canopy for outside exhaust of XPert Systems. | XPert Filtered Balance System |
| La cote de confinement ASHRAE 110-1995 telle que fabriquée est inférieure à 0.05 ppm à 4 lpm. p.18 ↗ | Baseline containment performance for field validation comparison. | All models |
| Les essais de confinement biologique à 75 fpm d'admission ont généralement montré 1 spore ou moins s'échappant par essai. p.19 ↗ | Supports use for biohazardous procedures at appropriate face velocity. | All models |
| Les essais de stabilité de la balance étaient excellents à 78 fpm et 100 fpm avec une balance à cinq décimales. p.19 ↗ | Confirms suitability for high-precision weighing within the recommended velocity range. | XPert Filtered Balance System |
| Chaque modèle d'enceinte pèse entre 125 et 350 lbs (55 à 152 kg). p.12 ↗ | Work surface and supporting structure must safely support this weight plus equipment. | All models |
| Un registre réglable (ou une vanne) doit être installé en cas de raccordement direct à un système d'évacuation du bâtiment. p.11 ↗ | Required to control airflow properly, especially when multiple enclosures share a house exhaust. | Models ducted to house exhaust |
| Le raccordement de mise à la terre ne doit pas être effectué sur le couvercle du boîtier de raccordement. p.17 ↗ | Electrical installation must follow this grounding restriction. | XPert Filtered Balance Station |
Faults & Troubleshooting
| Code / Symptôme | Possible Cause | Remedy | Note |
|---|---|---|---|
| Contaminants outside of enclosure. p.62 ↗ | Improper user techniques for the enclosure. | See “Certifying the Enclosure” Chapter 3 and “Safety Precautions” Chapter 4 sections in the manual. (Ref. Appendix D). | Ref. Appendix D |
| Contaminants outside of enclosure. p.62 ↗ | Restriction of the baffle air slots or blockage of the exhaust outlet. | Remove obstruction to ensure that all air slots and the exhaust outlet are unobstructed. | |
| Contaminants outside of enclosure. p.62 ↗ | External factors are disrupting the enclosure airflow patterns or acting as a source of contamination. | See “Location Requirements” Chapter 2, “Certifying the Enclosure” Chapter 3, and “Safety Precautions” Chapter 4 sections of this manual. (Ref. Appendix D). | Ref. Appendix D |
| Contaminants outside of enclosure. p.62 ↗ | Enclosure has improper face velocity. | Have enclosure certified and check exhaust system. Check HEPA filters for loading. Adjust enclosure speed control. Enclosure should have an average face velocity of 60-100 fpm for weighing procedures and 75-105 fpm for biohazardous procedures. | |
| Blower won’t operate. p.62 ↗ | Unit not plugged into outlet. | Plug the enclosure into appropriate electrical service. | |
| Blower won’t operate. p.62 ↗ | Circuit breaker(s) or Ground Fault Interrupter. | Reset circuit breaker. | |
| Blower won’t operate. p.62 ↗ | Blower wiring is disconnected. | Inspect blower wiring. | |
| Blower won’t operate. p.62 ↗ | Blower switch is defective. | Replace switch. | |
| Blower won’t operate. p.62 ↗ | Motorized impeller or blower is defective. | Replace motorized impeller or blower. See Chapter 6. | Chapter 6 |
| Low face velocity or poor containment of contaminants. p.62 ↗ | Enclosure sash not closed. | Close sash to the lowest position. | |
| Low face velocity or poor containment of contaminants. p.62 ↗ | HEPA filter clogged. | Replace HEPA filter or increase speed. | |
| Low face velocity or poor containment of contaminants. p.62 ↗ | Carbon filter loaded with chemicals. | Replace carbon filter. | |
| Blower and lights won’t operate. p.62 ↗ | Unit not plugged into outlet. | Plug enclosure into appropriate electrical service. | |
| Blower and lights won’t operate. p.62 ↗ | Circuit breaker(s) tripped. | Reset or replace circuit breaker. | |
| Lights do not work. p.63 ↗ | Lamp not installed properly. | Inspect lamp installation. | |
| Lights do not work. p.63 ↗ | Lamp wiring disconnected. | Inspect lamp wiring. | |
| Lights do not work. p.63 ↗ | Defective lamp. | Replace lamp. | |
| Lights do not work. p.63 ↗ | Light switch is defective. | Replace light switch. | |
| Lights do not work. p.63 ↗ | Defective electronic ballast. | Replace ballast. | |
| Airflow monitor malfunction. p.63 ↗ | No power. No lights. No display. | Power cable to circuit board is disconnected and needs to be connected. Sensor cable needs to be connected. Power supply is not plugged into proper voltage; plug in power supply. Verify that all airflow monitor interface cables are connected. Check fuses on enclosure. | |
| No audible alarm. p.63 ↗ | Alarm has been temporarily silenced using “SILENCE ALARM” or “enter” buttons. | Wrong alarm set point. Airflow monitor was not properly adjusted. Repeat calibration steps outlined in this manual in Chapter 6 or in the supplied Digital 1000 Monitor Manual. | Chapter 6 |
| Constant audible alarm. p.63 ↗ | Check airflow and calibration of airflow monitor. | See Chapter 6. | Chapter 6 |
| Continuous alarm. p.63 ↗ | Check the face velocity of the enclosure as the airflow of the system may have changed. | If incorrect, adjust the speed control to increase face velocity. The HEPA filter may have become loaded. If face velocity is correct, calibrate the airflow monitor outlined in this manual in Chapter 6. | Chapter 6 |
| Monitor alarms; air way to airflow monitor sensor is blocked by insects, dust or debris. p.63 ↗ | Airway to airflow monitor sensor is blocked by insects, dust or debris. | Lightly clean the airway with clean air. Be careful not to touch sensitive electrical components. | |
| Audible disable will not stay operational. p.63 ↗ | An alarm condition must be continuously present before the audible alarm can be silenced. If flow conditions fluctuate near the alarm set point, the airflow monitor will automatically reset it. | Action should be taken to bring the enclosure airflow into proper operating parameters or adjust the alarm set point lower. |