Induztr
Résumé technique Visionneuse de documents Modèles associés

MALDImini-1 Instruction Manual

Technical Reference Summary

Covered Models & Document Scope

Espectrómetro de masas MALDI de trampa de iones digital MALDImini-1 (Shimadzu). El manual cubre el instrumento base, sus accesorios, piezas opcionales (p. ej., Piping Set for Gas Cylinder), placas de muestra (desechables para microscopio y SUS) y el software MALDImini Server / Console / Maintenance. No se describen códigos de pedido ni variantes de modelo más allá del MALDImini-1.

Section-by-Section Technical Breakdown

pp. 6-10, 144-145
Lugar de instalación y condiciones

Define las condiciones físicas, ambientales y eléctricas necesarias para instalar el MALDImini-1. Especifica la carga sobre la mesa, los espacios libres, los rangos de temperatura y humedad, las características de la fuente de alimentación y los requisitos de puesta a tierra.

  • Bench/floor must support instrument weight of 25 kg plus PC system and table.
  • Minimum clearances: 10 cm rear, 5 cm left/right/top; 70 cm rear/left/right for maintenance; 50 cm table surface to the left for the folding chassis.
  • Room temperature 18 to 26 °C with changes within ±3 °C; humidity 40 to 70 % non-condensing.
  • Indoor location, overvoltage category II, pollution degree 2, elevation ≤ 2000 m.
  • Power supply 100 to 240 V AC (50/60 Hz), 960 VA, voltage fluctuation within ±10 V, dedicated circuit with electrical leakage breaker and earth ground.
pp. 119-129
Conexión del instrumento y ajustes de comunicación

Cubre la conexión del instrumento a la alimentación, al gas y al PC de control, y la configuración de los ajustes de comunicación Ethernet entre el instrumento y el software MALDImini.

  • Connect only to the specified power supply; check the nameplate for voltage specification.
  • Ethernet cable connection is required for communication with the instrument.
  • Communication settings are configured in the software (Section 10.1.3).
  • Gas supply uses helium and argon lines with regulator and Swagelok-type connections.
pp. 100-102, 127-129, 145
Gas utilizado

Describe los gases necesarios para el funcionamiento (helio y argón), sus líneas de suministro, los ajustes del regulador y el procedimiento de purga.

  • Helium and argon gas supply lines are monitored; low pressure triggers warning WRN??-06-01 / WRN??-06-02.
  • Regulator settings and gas line nut tightness must be checked if pressure is low.
  • Gas line purging procedure is given in Section 8.4.
pp. 14, 21-23, 118
Arranque y parada del instrumento

Proporciona los procedimientos de arranque, arranque/parada diarios y parada de emergencia, incluido el tiempo de espera tras el apagado y el comportamiento en caso de corte de energía.

  • After turning power OFF, wait at least 10 seconds before turning it back ON.
  • Emergency shutdown: turn OFF mains switch (rear, above power cable), close gas supply, disconnect power plug.
  • After a power outage the vacuum system restarts automatically when power is restored; long outages require emergency-stop procedure then normal startup and gas purging.
pp. 11-20
Placas de muestra y preparación de muestras

Describe las placas de muestra recomendadas, su limpieza (básica y química), la preparación de muestras de calibración estándar/mixtas y la carga/registro de muestras.

  • Use only Shimadzu-recommended sample plates; other plates may damage the instrument.
  • Sample must be dry before opening the door and inserting the plate.
  • Wear powder-free gloves when handling plates and opening the sample door.
  • Cleaning procedures: basic cleaning and chemical cleaning.
pp. 24-39, 142
Operación básica y análisis

Cubre el flujo de trabajo de análisis: inserción de la placa de muestra, activación de voltajes, calibración, análisis MS, MS/MS y MS3, y apagado/extracción de la placa.

  • Workflow: set-up, calibration, analysis, settlement.
  • MSn analysis requires appropriate isolation and CID parameters.
  • Wait approximately 30 minutes after applying voltage before measurement for temperature stability; on first switch to [Ready] after mains ON, run an analysis and wait.
pp. 40-93, 130
Ajustes y parámetros avanzados

Documenta los paneles de parámetros del software: ajustes de adquisición, ajustes de rasterizado, calibración de masas, procesamiento de espectros, ajustes de visualización y adquisición por lotes.

  • Acquisition settings include number of measurements and measurement conditions.
  • Mass calibration panel relates time and m/z.
  • Spectrum processing includes baseline subtraction, smoothing and peak detection.
  • Batch acquisition supports batch tables, editing, loading and saving.
pp. 22, 95-108, 147
Mantenimiento

Enumera las inspecciones periódicas y el mantenimiento, la limpieza, la inspección/sustitución de la junta tórica de la puerta de muestras, la purga de la línea de gas, las pruebas de control de calidad del cliente y los procedimientos de devolución/reparación del instrumento.

  • Periodic inspection/calibration should be requested from Shimadzu representative.
  • Customer QC tests: High Mass Test and Mass Resolution Test.
  • Turbomolecular pump overhaul is handled via instrument return.
  • Replacement parts available for 7 years after discontinuation.
pp. 112-118, 140-146
Solución de problemas

Proporciona tablas de problema/causa/acción correctiva para problemas generales y de adquisición de datos, códigos de mensajes de error/advertencia, notificaciones de tiempo de funcionamiento, comprobación de archivos de registro y manejo de cortes de energía.

  • Indicator states: pink steady = stage initialization error; pink flashing = vacuum operation; light blue = ready; red flashing = error.
  • Error codes format ERR/WRN<system status>-<cause>-<details>.
  • Log files stored in C:\MALDImini-1\Log, separated by date.
  • Operating-time notifications appear in MALDImini Console.
pp. 15, 142-145
Especificaciones

Enumera las especificaciones de rendimiento, hardware, software e instalación del MALDImini-1.

  • Laser: Nd:YLF, 349 nm, 60 µJ @ 1 kHz, pulse width < 5 ns, beam divergence 3.2 ± 0.5 mrad.
  • Class 1 laser product per IEC60825-1:2014 and JIS C 6802 (2018).
  • Power: 100 to 240 V AC, 50/60 Hz, 960 VA.
  • Weight: 25 kg.
pp. 147
Piezas de mantenimiento

Enumera las piezas consumibles y de reparación del instrumento.

  • Consumable parts and repair parts are listed in Sections 12.1 and 12.2.
  • Use only specified parts when replacing.

Key Integration, Operating & Safety Requirements

Specification / Condition Engineering Implication S'applique à
El peso del instrumento es de 25 kg; la mesa/suelo debe soportar el instrumento más el sistema de PC y la mesa. p.6 ↗ Select a stable bench rated for the full load to prevent tipping or injury. MALDImini-1
Espacio libre mínimo: 10 cm en la parte trasera, 5 cm a izquierda/derecha/superior; 70 cm en la parte trasera/izquierda/derecha para mantenimiento; 50 cm de superficie de mesa a la izquierda para plegar el chasis. p.7 ↗ Plan lab layout to allow airflow and service access. MALDImini-1
Entorno de funcionamiento: 18 a 26 °C con cambios dentro de ±3 °C; humedad del 40 al 70 % sin condensación; interior, categoría de sobretensión II, grado de contaminación 2, altitud ≤ 2000 m. p.8 ↗ HVAC must maintain tight temperature stability for reproducible measurements. MALDImini-1
Fuente de alimentación: 100 a 240 V CA (50/60 Hz), 960 VA; fluctuación de tensión dentro de ±10 V; circuito dedicado con interruptor de fuga eléctrica y toma de tierra. p.9 ↗ Do not share the circuit with other instruments; verify capacity and grounding. MALDImini-1
Después de apagar la alimentación, espere al menos 10 segundos antes de volver a encenderla. p.11 ↗ Prevents instrument failure from rapid power cycling. MALDImini-1
Láser: Nd:YLF, longitud de onda 349 nm, energía de pulso 60 µJ @ 1 kHz, anchura de pulso < 5 ns FWHM, divergencia del haz 3.2 ± 0.5 mrad. p.15 ↗ Defines the ionization source characteristics relevant to matrix selection and fluence settings. MALDImini-1
Producto láser de clase 1 según IEC60825-1:2014 y JIS C 6802 (2018); láser interno equivalente a clase 4. p.15 ↗ Covers must not be removed; internal service only by Shimadzu personnel. MALDImini-1
Espere aproximadamente 30 minutos después de aplicar voltaje antes de iniciar la medición; en el primer cambio a [Ready] tras encender la alimentación, realice un análisis y espere. p.142 ↗ Temperature stabilization is required for mass accuracy and resolution. MALDImini-1
Utilice únicamente placas de muestra recomendadas por Shimadzu; la muestra debe estar seca antes de abrir la puerta. p.11 ↗ Non-recommended plates or wet samples may damage the instrument or impair vacuum. MALDImini-1
Use guantes sin polvo al abrir la puerta de muestras y al colocar/retirar las placas de muestra. p.11 ↗ Prevents contamination that degrades evacuation performance. MALDImini-1
Apagado de emergencia: apague el interruptor principal (parte trasera, encima del cable de alimentación), cierre el suministro de gas, desconecte el enchufe de alimentación. p.14 ↗ Defines the safe shutdown sequence for abnormalities. MALDImini-1
Tras un corte de energía, el sistema de vacío se reinicia automáticamente cuando se restablece la alimentación; los cortes prolongados requieren el procedimiento de parada de emergencia y luego el arranque normal y la purga de gas. p.14 ↗ Plan for unattended restarts and purge gas lines after extended outages. MALDImini-1
Formato de códigos de error: ERR o WRN<Código de estado del sistema>-<Código de causa>-<Código de detalles>, cada uno un número de 2 dígitos. p.144 ↗ Enables interpretation of error messages for corrective action. MALDImini-1
Los archivos de registro se almacenan en C:\MALDImini-1\Log, separados por fecha, legibles con un editor de texto. p.146 ↗ Useful for diagnosing intermittent faults. MALDImini-1
Piezas de repuesto disponibles durante 7 años después de la discontinuación del producto. p.22 ↗ Long-term maintenance planning should account for this availability window. MALDImini-1
Las pruebas de control de calidad del cliente incluyen High Mass Test y Mass Resolution Test. p.103 ↗ Periodic performance verification can be performed by the customer. MALDImini-1
No someta el instrumento a impactos ni vibraciones; no lo mueva ni lo incline durante el funcionamiento. p.11 ↗ Prevents misalignment of the optical system and damage to the turbomolecular pump. MALDImini-1
No limpie con alcohol ni disolventes a base de diluyente; limpie con un paño suave humedecido con agua o detergente neutro diluido y luego seque. p.12 ↗ Avoids rust or discoloration of covers. MALDImini-1

Faults & Troubleshooting

Code / Symptôme Possible Cause Remedy Note
The indicator does not light up when the power is turned ON. p.140 ↗ Power cable not properly connected or no 100 to 240 V power at distribution panel. Check that the power cable is properly connected and 100 to 240 V power is being supplied to the distribution panel. 9.1.1 General
Unable to connect to instrument. p.140 ↗ Ethernet cable connection problem. Check the connection of the Ethernet cable. 9.1.1 General
The initialization operation does not end. (indicator lights up in pink) p.140 ↗ Stage initialization error. Contact your Shimadzu representative. 9.1.1 General
The initialization operation does not end. (indicator flashes in pink) p.140 ↗ Vacuum operation being performed; sample door may not be closed; instrument may have been inactive for a long time. Check the gauge to see whether the vacuum is changing. Check that the sample door is closed. If the vacuum value has completely stopped changing, contact your Shimadzu representative. 9.1.1 General
The instrument does not enter [Ready] mode. p.140 ↗ Initialization operation or vacuum operation may not be complete. Check that the indicator lights up in light blue. 9.1.1 General
The gas cylinder becomes depleted quickly. p.140 ↗ Gas leak in the connecting parts. Check the connecting parts. 9.1.1 General
The stage vacuum operation does not end. p.140 ↗ Sample door may not be closed, or seal surface of sample door may be contaminated. Clean the seal surface and O-ring. 9.1.1 General
The indicator flashes in red. p.140 ↗ An error was detected. Turn OFF the power to the instrument and restart it. 9.1.1 General
The camera image is not displayed. p.140 ↗ Not specified. Contact your Shimadzu representative. 9.1.1 General
The ion intensity is unstable or low. p.142 ↗ Method file or batch file not appropriate. Check the method file or batch file. 9.1.2 Data Acquisition
The mass accuracy and mass resolution cannot be obtained. p.142 ↗ Laser intensity not appropriate, resulting in insufficient or excessive ions; instrument temperature not stable. Adjust the laser intensity. Wait approximately 30 minutes after applying voltage before starting measurement. On first switch to [Ready] after mains ON, click [Start] to run an analysis and wait. 9.1.2 Data Acquisition
The MSn spectrum cannot be obtained. p.142 ↗ Isolation parameter or CID parameter not appropriate. Check the isolation parameter. Check the CID parameter. 9.1.2 Data Acquisition
ERR02-05-01 or ERR02-05-02 p.144 ↗ Timeout occurred in vacuum operation (rough pumping). Instrument power turned ON while sample door open; or foreign object caught in sample door / door dirty. Close the sample door and turn ON the power again. If error persists, contact Shimadzu. If foreign object/dirt: use ethanol to clean the area where the sample door touches the O-ring, then close door and turn ON power again. 9.2 Error/Warning Messages
ERR02-05-08 or ERR02-05-09 p.144 ↗ Timeout occurred in vacuum operation (TMP). Vacuum performance decreased due to condensation in vacuum piping or other area; or leak due to dirty O-ring contact area. Turn ON the power again and check for the error. If leak suspected: use ethanol to clean the area where the sample door touches the O-ring, close door and turn ON power again. If error persists, contact Shimadzu. 9.2 Error/Warning Messages
ERR04-05-01 p.144 ↗ Decrease in vacuum during measurement was detected. Leakage of vacuum piping and deterioration of vacuum equipment suspected. Make a note of the error code that occurred, and contact your Shimadzu representative. 9.2 Error/Warning Messages
ERR06-05-01 p.144 ↗ Timeout occurred in vacuum operation (rough pumping) after replacing the sample. Foreign object caught in sample door or door dirty. Use ethanol to clean the area where the sample door touches the O-ring, then close the sample door and turn ON the power again. If error persists, contact Shimadzu. 9.2 Error/Warning Messages
ERR06-05-04 p.145 ↗ Timeout occurred in vacuum operation (TMP) after replacing the sample. Vacuum performance decreased due to condensation; or leak due to dirty O-ring contact area. Turn ON the power again and check for the error. If leak suspected: turn ON power again, open door after instrument enters standby mode, then use ethanol to clean the area where the sample door touches the O-ring. If error persists, contact Shimadzu. 9.2 Error/Warning Messages
WRN??-06-01 p.145 ↗ The gas pressure of the helium gas supply line is low. Leak or other abnormality in gas supply line suspected. Check that the regulator settings are correct and that the gas supply line nuts are not loose. 9.2 Error/Warning Messages; ?? varies with instrument state
WRN??-06-02 p.145 ↗ The gas pressure of the argon gas supply line is low. Check that the regulator settings are correct and that the gas supply line nuts are not loose. 9.2 Error/Warning Messages; ?? varies with instrument state
Other error codes p.145 ↗ Not specified. Make a note of the error code that occurred, and contact your Shimadzu representative. 9.2 Error/Warning Messages

Modèles liés