Instruction Manual - Nexis GC-2030
Technical Reference Summary
Covered Models & Document Scope
Este documento es el Manual de Instrucciones del cromatógrafo de gases Shimadzu Nexis™ GC-2030. Cubre procedimientos de resolución de problemas y mantenimiento para el sistema GC-2030, incluidos puertos de inyección (SPL, PTV, OCI), detectores (FID, TCD, PTCD, FTD, FPD), controladores de flujo (AFC, APC) y componentes relacionados. No se enumeran variantes de modelo específicas ni códigos de pedido en las páginas proporcionadas.
Section-by-Section Technical Breakdown
Esta sección aborda problemas en los que la presión o el caudal no se pueden ajustar o no alcanzan el valor establecido, y en los que las fugas de gas no se pueden detener. Proporciona causas y soluciones, incluidos rangos de presión de suministro, procedimientos de verificación de fugas para columnas capilares y empaquetadas, y acciones correctivas para piezas con fugas.
- Supply pressure ranges: carrier gas (other than hydrogen) 300–980 kPa; carrier gas (hydrogen) 150–500 kPa; detector gas 300–980 kPa; hydrogen 150–300 kPa; air 300–500 kPa.
- Carrier gas leak check for capillary columns: set inlet pressure to 150 kPa, total flow 100 mL/min, wait 10 minutes, and compare pressure drop against leak judgment table.
- Leak judgment: pressure drop >2.5 kPa (below 150 kPa), >5.0 kPa (150–450 kPa), >7.5 kPa (450–600 kPa), >10.0 kPa (600–750 kPa), >12.5 kPa (above 750 kPa).
- Leak check points: septum, around injection port, tubing connections, split vent, purge vent, column connection.
- Corrective actions: replace septum, replace O-ring of glass insert, replace seal of blank nut, replace blank nut, replace ferrule/column nut/ClickTek connector.
- Do NOT use leak detecting fluid or soapy water on connections above the carrier and detector gas controllers (AFC/APC).
- The instrument allows 0.2 mL/min leakage from split/purge vent.
Esta sección cubre el problema de que la temperatura no aumenta o no alcanza el valor establecido. Enumera causas como que el GC no se ha iniciado, tiempo de inicio prolongado, pérdida de calor, ajuste de temperatura máxima bajo, temperatura del detector inferior a la temperatura de la columna y programas INJ/horno no coincidentes, junto con soluciones.
- Press [Start GC] on the [GC Start Sequence] screen to start the GC.
- Set start time at a lower value if heating has not started.
- Close the oven door and close the hole of the insulation to prevent heat loss.
- Increase the maximum temperature setting for the column and other units; set [Max Usable Temp] on the [Column Information] screen correctly.
- Set the detector temperature larger than the column temperature.
- Set the total time of the INJ program to match the total time of the oven program.
Esta sección proporciona resolución de problemas para problemas comunes del detector: ausencia de picos o picos extremadamente pequeños, ruido de línea base alto, deriva de línea base o fluctuación a largo plazo, y error de ajuste de cero. Se enumeran causas y soluciones para todos los detectores.
- Check signal cable connections of detector and data processing unit.
- Turn [On] the detector control.
- Check for gas leaks at detector-column connection and tighten.
- Install column correctly with correct insertion length on detector side.
- Set detector attenuation, range, and current at appropriate values.
- Perform Auto Zero if zero level is far below '0'.
- Increase injection volume (normally less than 2 µL for liquid samples and less than 1 mL for gas samples) or increase sample concentration.
- Reduce split ratio for split analysis.
- Check syringe for clogging or leaks; replace if necessary.
- Replace glass insert with deactivated type or acid/alkaline treated one depending on component.
- Set detector gas flow and filter time constant at proper (recommended) values.
- Change analytical conditions such as temperature or column flow if incorrect.
Key Integration, Operating & Safety Requirements
| Specification / Condition | Engineering Implication | S'applique à |
|---|---|---|
| Presión de suministro de gas portador (distinto de hidrógeno): 300 a 980 kPa. p.55 ↗ | Ensure supply pressure is within this range to allow proper pressure/flow control. | GC-2030 series |
| Presión de suministro de gas portador (hidrógeno): 150 a 500 kPa. p.55 ↗ | Use this range when hydrogen is used as carrier gas. | GC-2030 series |
| Presión de suministro de gas del detector: 300 a 980 kPa. p.55 ↗ | Ensure detector gas supply is within this range. | GC-2030 series |
| Presión de suministro de hidrógeno para el detector: 150 a 300 kPa. p.55 ↗ | Use this range for hydrogen detector gas. | GC-2030 series |
| Presión de suministro de aire: 300 a 500 kPa. p.55 ↗ | Ensure air supply is within this range. | GC-2030 series |
| Verificación de fugas de gas portador para columnas capilares: ajuste la presión de entrada a 150 kPa, el flujo total a 100 mL/min, espere 10 minutos y compare la caída de presión con la tabla de juicio de fugas. p.57 ↗ | Use this procedure to verify system leak-tightness. | GC-2030 with capillary column |
| Juicio de fuga: si la presión de entrada inicial es inferior a 150 kPa, una disminución superior a 2.5 kPa indica una fuga. p.58 ↗ | Use this threshold to determine if a leak exists. | GC-2030 series |
| Juicio de fuga: si la presión de entrada inicial es de 150 a 450 kPa, una disminución superior a 5.0 kPa indica una fuga. p.58 ↗ | Use this threshold to determine if a leak exists. | GC-2030 series |
| Juicio de fuga: si la presión de entrada inicial es de 450 a 600 kPa, una disminución superior a 7.5 kPa indica una fuga. p.58 ↗ | Use this threshold to determine if a leak exists. | GC-2030 series |
| Juicio de fuga: si la presión de entrada inicial es de 600 a 750 kPa, una disminución superior a 10.0 kPa indica una fuga. p.58 ↗ | Use this threshold to determine if a leak exists. | GC-2030 series |
| Juicio de fuga: si la presión de entrada inicial es superior a 750 kPa, una disminución superior a 12.5 kPa indica una fuga. p.58 ↗ | Use this threshold to determine if a leak exists. | GC-2030 series |
| El instrumento permite una fuga de 0.2 mL/min desde el venteo de split/purge. p.60 ↗ | This is an acceptable leak rate; higher leakage may require maintenance. | GC-2030 series |
| NO utilice líquido detector de fugas ni agua jabonosa en conexiones por encima de los controladores de gas portador y del detector (AFC/APC). p.60 ↗ | Drips may damage the controller; use a leak detector instead. | GC-2030 series |
| Normalmente, el volumen de inyección debe ser inferior a 2 µL para muestras líquidas e inferior a 1 mL para muestras gaseosas. p.62 ↗ | Exceeding these volumes may contaminate the injection port. | GC-2030 series |
| Para la verificación de fugas, utilice una tuerca ciega (P/N tipo G: 221-35566-92) y una junta de columna (P/N: 201-35184) en el venteo de purga; para SPL o PTV, instale también una tuerca ciega en el venteo de split. p.57 ↗ | These parts are required to seal vents during leak testing. | GC-2030 with SPL/PTV |
Faults & Troubleshooting
| Code / Symptôme | Possible Cause | Remedy | Note |
|---|---|---|---|
| No gas is supplied. p.85 ↗ | No gas is supplied. | Open the gas cylinder main valve to supply gas. Turn [On] the detector/injection port control. Turn [On] the detector gas control. | See also 7.5 Injection Port (P.196), 7.4 Detector (P.139), 7.4.9 Settings for Detector Gas Program (P.175) |
| Supply pressure is low. p.85 ↗ | Supply pressure is low. | Change the supply pressure of the gas. Carrier gas (other than hydrogen): 300 to 980 kPa; Carrier gas (Hydrogen): 150 to 500 kPa; Detector gas: 300 to 980 kPa; Hydrogen: 150 to 300 kPa; Air: 300 to 500 kPa. | See also 8.3.2 Gas Supply Pressure (P.348) |
| Gas leaks. p.85 ↗ | Gas leaks. | Check for gas leaks, and tighten leaking connections. Replace the gasket or septum. Additionally tighten the graphite ferrule. If there is leakage even after additional tightening, replace it. | See also Carrier gas leak check (Capillary) (P.57) |
| Set value is incorrect. p.86 ↗ | Set value is incorrect. | Set pressure at a proper value. | See also 8.6 AFC, APC (P.372) |
| Set value is outside controllable range. p.86 ↗ | Carrier gas type or column information is incorrect. | Set the carrier gas type or column information correctly. | See also 7.5 Injection Port (P.196), 7.6.2 [Column Information] Screen (P.241) |
| Total flow is too low, and pressure cannot increase. p.86 ↗ | Total flow is too low, and pressure cannot increase. | Increase the total flow. | See also 8.6 AFC, APC (P.372) |
| Split ratio is set at a low value and total flow is low. p.86 ↗ | Split ratio is set at a low value and total flow is low. | Increase split ratio to increase the total flow. | |
| Split line filter is clogged. p.86 ↗ | Split line filter is clogged. | Replace the filter of the split line. | See Maintenance Help |
| Even if total flow is increased, the actual flow of the split vent is low and the pressure is high. p.86 ↗ | Split line filter is clogged. | Replace the filter of the split line. | See Maintenance Help |
| Part is incorrectly installed. p.86 ↗ | Part is incorrectly installed. | Install parts correctly. | |
| Graphite ferrule or other seal such as O-ring is damaged. p.86 ↗ | Graphite ferrule or other seal such as O-ring is damaged. | Replace O-ring. Additionally tighten the graphite ferrule. If there is leakage even after additional tightening, replace it. | See Maintenance Help |
| Tubing including pipes and joints is damaged. p.86 ↗ | Tubing including pipes and joints is damaged. | Replacement of the tubing part is required. Turn off the main power of the instrument, shut off gas supplies, and contact your Shimadzu sales/service representative. | |
| GC has not started yet. p.91 ↗ | GC has not started yet. | Press [Start GC] on the [GC Start Sequence] screen to start the GC. | See also 7.1.1 [GC Start Sequence] Screen (P.98) |
| Because start time is too long, heating has not started yet. p.91 ↗ | Because start time is too long, heating has not started yet. | Set the start time at a lower value. Immediately after this setup value is changed, the new value is in effect. | See also 7.1.1 [GC Start Sequence] Screen (P.98) |
| Heat loss is large. p.91 ↗ | Heat loss is large. | Close the oven door. Close the hole of the insulation. | |
| Because maximum temperature is set at a very low value, an overheat error occurs. p.91 ↗ | Because maximum temperature is set at a very low value, an overheat error occurs. | Increase the maximum temperature setting for the column and other units. Set [Max Usable Temp] on the [Column Information] screen correctly. | See also [Max Temperature] Screen (P.284), 7.6.2 [Column Information] Screen (P.241) |
| Detector temperature is lower than the set value of column temperature. p.91 ↗ | Detector temperature is lower than the set value of column temperature. | Set the detector temperature larger than the column temperature. | See also 7.4 Detector (P.139) |
| The INJ program does not match the oven program. p.91 ↗ | The INJ program does not match the oven program. | Set the total time of the INJ program to match the total time of the oven program. | See also 7.5.4 [INJ/FLOW] Screen (OCI) (P.208), 7.5.5 [INJ/FLOW] Screen (PTV) (P.212) |
| Signal cable of the detector is connected incorrectly. p.91 ↗ | Signal cable of the detector is connected incorrectly. | Connect the signal cable correctly. | See Maintenance Help |
| Detector control is turned [Off]. p.91 ↗ | Detector control is turned [Off]. | Turn [On] the detector control. | See also 7.4 Detector (P.139) |
| Signal cable of the data processing unit is connected incorrectly. p.91 ↗ | Signal cable of the data processing unit is connected incorrectly. | Connect the signal cable correctly. | See also 8.9 Connecting to External Devices (P.404) |
| There is a leak at the connection of the detector with the column. p.91 ↗ | There is a leak at the connection of the detector with the column. | Check for gas leaks, and tighten leaking connections. | See also Carrier gas leak check (Capillary) (P.57) |
| The length of the inserted column on the detector side is incorrect. p.91 ↗ | The length of the inserted column on the detector side is incorrect. | Install the column correctly. | See Maintenance Help |
| Detector attenuation, range, or current is not appropriate. p.92 ↗ | Detector attenuation, range, or current is not appropriate. | Set the detector attenuation, range, and current at appropriate values. | See also 7.4 Detector (P.139) |
| Zero level is far below "0". p.92 ↗ | Zero level is far below "0". | Check the signal level on the Monitor screen and perform Auto Zero. | See also 7.2 Monitor (P.111) |
| Injection volume is too low. Or sample concentration is low. p.92 ↗ | Injection volume is too low. Or sample concentration is low. | Increase the injection volume. (Normally, less than 2 μL for liquid samples and less than 1 mL for gas samples.) Large injection volume may contaminate the injection port. Increase the sample concentration. | |
| Split ratio is too high. (For split analysis) p.92 ↗ | Split ratio is too high. (For split analysis) | Reduce the split ratio. | See also 7.5.1 [INJ/FLOW] Screen (SPL) (P.196), 7.5.5 [INJ/FLOW] Screen (PTV) (P.212) |
| Sample is injected incorrectly. p.92 ↗ | Sample is injected incorrectly. | Check the clogging or leaks of the syringe and repair it. Replace the syringe. | See Maintenance Help |
| Component is adsorbed in the glass insert. p.92 ↗ | Component is adsorbed in the glass insert. | Replace the glass insert with deactivated type. Replace the glass insert with acid or alkaline treated one depending on the component. | See Maintenance Help |
| Detector gas flow is incorrect. p.92 ↗ | Detector gas flow is incorrect. | Set it at a proper (recommended) value. | See Maintenance Help |
| Detector filter time constant is incorrect. p.92 ↗ | Detector filter time constant is incorrect. | Set it at a proper (recommended) value. | See also 7.4.10 [Signal Settings] Screen (P.177) |
| Analytical conditions, such as temperature or column flow are incorrect. p.92 ↗ | Analytical conditions, such as temperature or column flow are incorrect. | Change the analytical conditions. |