Induztr
Engineering Digest Document Viewer Related Models

Agilent 6400 Series Triple Quadrupole LC/MS Concepts Guide

Technical Reference Summary

Covered Models & Document Scope

Covers the Agilent 6400 Series Triple Quadrupole LC/MS models 6410, 6420, 6430, 6460, 6470, 6490, 6495, 6495A and 6495B, including ion source options ESI, APCI, APPI, AJS and MMI, and MassHunter Data Acquisition software version B.08.02 or higher.

Section-by-Section Technical Breakdown

pp. 8
System Configurations and Ion Sources

The 6400 Series can be configured for normal-flow, microflow or nanoflow LC/MS. Supported ion sources are ESI, APCI, APPI, AJS and MMI depending on model. The 6460, 6470, 6490 and 6495 support the AJS source; the 6490 and 6495 add iFunnel technology.

  • Normal flow: binary or quaternary pump with well-plate, autosampler or CTC PAL autosampler; ESI, APCI, APPI, MMI sources.
  • Microflow: capillary pump with micro well-plate sampler or CTC PAL micro-plate autosampler; ESI, APCI or MMI sources.
  • Nanoflow: nanoflow pump, capillary pump and micro well-plate sampler for narrow peak dispersion and lower dead volumes.
  • 6490 and 6495 use iFunnel technology: dual offset ion funnel, AJS source, shorter desolvation assembly with hexabore capillary, curved collision cell.
pp. 23-24, 28-29, 31-32
Model Highlights and Hardware Differences

Each model in the 6400 Series adds specific hardware features. The 6420 has one turbo and one rough pump with a resistive capillary; the 6430 adds a second turbo pump and updated collision cell lenses; the 6460 supports AJS and 3000 m/z quadrupoles; the 6470 adds improved ion optics, a new detector, CATT2 and a 5-3000 m/z range; the 6490 uses iFunnel and CATT1 with 5-1400 m/z; the 6495 uses iFunnel and CATT2 with 5-2250 m/z; the 6495B adds Gate Valve Technology and extends the mass range to 3000 amu.

  • 6420: one turbo pump, one rough pump, resistive capillary.
  • 6430: additional turbo pump, improved vacuum stage 2 pumping, updated collision cell lenses.
  • 6460: supports AJS source, 3000 m/z Q1 and Q2 quadrupoles.
  • 6470: AJS source, improved ion optics, new detector with high energy conversion dynode, high throughput quadrupole driver, CATT2, mass range 5-3000 m/z.
  • 6490: iFunnel technology, additional rough pump for ion funnel, CATT1, mass range 5-1400 m/z.
  • 6495: improved ion optics, new detector, iFunnel, additional rough pump, CATT2, mass range 5-2250 m/z.
  • 6495B: Gate Valve Technology allows capillary replacement without venting; mass range extended to 3000 amu.
pp. 37-39
Dynamic MRM Operation

Dynamic MRM uses a single continuous time segment with up to 4000 transitions. Transitions are automatically grouped into MRM tables of up to 200 transitions based on retention time windows, allowing longer dwell times by acquiring transitions only around compound elution times.

  • Up to 4000 transitions in the Scan Segments table.
  • Transitions separated into MRM tables of up to 200 transitions each.
  • Each transition acquired from Ret Time - 1/2*(Delta Ret Time) to Ret Time + 1/2*(Delta Ret Time).
  • Data Acquisition software creates a lookup recipe grouping transitions into up to 1000+ MRM tables in the DSP.
  • Benefit: longer dwell times by performing MRM transitions around elution time rather than continuously.
pp. 40-44
Triggered Dynamic MRM

Triggered Dynamic MRM acquires confirmatory secondary MRMs when primary MRM abundances exceed set thresholds and other criteria are met. Up to two primary MRMs per compound can be designated as Trigger MRMs. Trigger Entrance Delay, Trigger Delay and Trigger Window control when secondary transitions are acquired.

  • Up to two Trigger MRMs per compound.
  • Secondary transitions acquired only when Trigger MRM abundances exceed thresholds.
  • Trigger Entrance Delay: number of scans to skip after thresholds met within Trigger Window.
  • Trigger Delay: number of scans to skip between acquiring each secondary transition.
  • Trigger Window default is 0, meaning the same as the Peak Retention Time window; value entered is full width in minutes.
pp. 50-52
Sensitivity and Noise Reduction

The 6400 Series achieves high sensitivity through orthogonal spray sources, heated counter-current drying gas, dielectric capillary and skimmer, RF octopole ion guide, hyperbolic quadrupoles, and curved high-pressure collision cells. The 6470 combines noise reduction features from the 6460 and 6495.

  • Orthogonal spray sources maximize ionization while minimizing solvent and matrix noise.
  • Heated counter-current drying gas, dielectric capillary and skimmer enhance desolvation and minimize chemical noise.
  • Curved, high pressure collision cell optimizes MS/MS fragmentation while eliminating crosstalk even at very low dwell times.
  • 6470 uses hexapole field axial focusing curved collision cell with tapered cell structure.
  • 6420 and 6460 use high pressure collision cell with linear acceleration and small diameter high frequency hexapole assembly.
pp. 55
Linearity of the Triple Quadrupole LC/MS

Verapamil analyses demonstrate linear dynamic ranges of six orders of magnitude for the 6470, 6490 and 6495, and five orders of magnitude for the 6460, 6430 and 6420.

  • 6470, 6490, 6495: six orders of magnitude linear dynamic range.
  • 6460, 6430, 6420: five orders of magnitude linear dynamic range.
  • Example calibration curve: 100 attograms to 100 picograms on-column, six orders of magnitude, acquired with 6495 and AJS source.
pp. 58-61
Mass Spectrometer Ion Sources

The AJS source uses superheated nitrogen sheath gas collinear and concentric to the electrospray for efficient desolvation. The 6490A and 6495 use a resistive capillary with 6 inlets sampling up to 10X more ion-rich gas. The 6410 uses a glass dielectric cold capillary. APCI is suited for smaller, thermally stable polar and non-polar compounds. The G1978B Multimode Source combines ESI and APCI in separated zones.

  • AJS parameters: superheated nitrogen sheath gas temperature and flow rate, and nozzle voltage.
  • 6490A and 6495 resistive capillary has 6 capillary inlets and samples up to 10X more ion-rich gas.
  • 6410 glass dielectric cold capillary enhances desolvation and focusing of high mass ions while minimizing chemical noise.
  • APCI does not generate multiply charged ions and operates at higher temperatures.
  • G1978B Multimode Source: ESI and APCI zones separated in space; simultaneous operation can cause up to a factor of two sensitivity loss for some compounds.
pp. 65
Collision Cell

The collision cell is a high pressure hexapole assembly with linear acceleration to optimize MS/MS fragmentation while eliminating crosstalk even at very low dwell times. The hexapole field axial focusing curved collision cell includes a tapered cell structure for increased ion acceptance and reduced ionizer-generated noise.

  • High pressure hexapole assembly with linear acceleration.
  • Eliminates crosstalk even at very low dwell times.
  • Curved collision cell has tapered cell structure for increased ion acceptance at entrance.
  • Structure reduces ionizer-generated noise.
pp. 71
Pumping System

The 6490 and 6495 use two rough pumps and a three-stage turbo pump for the first five vacuum stages, with a second turbo pump on the last stage. The 6470 uses a single roughing pump and three-stage turbo pump for the first four vacuum stages, with a second turbo pump on the fourth stage.

  • 6490/6495: two rough pumps needed to decrease pressure in dual-stage ion funnel.
  • 6490/6495: second turbo pump added to last vacuum stage for gas load from curved collision cell.
  • 6470: single roughing pump and three-stage turbo pump partitioned for multiple vacuum stages.
  • 6470: second turbo pump added to fourth vacuum stage for gas load from enhanced collision cell.
pp. 77
Tuning

Checktune verifies peak width and mass axis before acquisition and takes approximately 3 to 5 minutes per polarity. Autotune is needed only after preventative maintenance or if Checktune fails; duration is 15-20 minutes per polarity for most models, 45 minutes per ionization mode for the 6490, and 25 minutes per ionization mode for the 6495. The calibrant delivery system is switched on automatically during tuning.

  • Checktune: approximately 3 to 5 minutes per polarity.
  • Autotune: 15 to 20 minutes per polarity for all models except 6490 and 6495.
  • Autotune: 6490 approximately 45 minutes per ionization mode; 6495 approximately 25 minutes per ionization mode.
  • Mark Tune from factory default only if regular Autotune fails or tune file is corrupted.
  • Calibrant delivery system (CDS) switched on automatically during tune.
pp. 75-76, 80
Acquisition

The Data Acquisition program controls and monitors Agilent LC modules and the Triple Quadrupole LC/MS from a single interface. The Instrument Status, Chromatogram Plot and Spectrum Plot windows can be closed for easier viewing, but at least one window must remain open.

  • All LC and MS parameters immediately visible.
  • Real-time plots show instrument at work.
  • Worklist spreadsheet-like interface handles multiple samples.
  • Chromatogram Plot window can show MS and UV chromatograms in real time.
  • At least one window must always be open.

Key Integration, Operating & Safety Requirements

Specification / Condition Engineering Implication Applies To
Dynamic MRM supports up to 4000 transitions, automatically grouped into MRM tables of up to 200 transitions each. p.37 ↗ Method design can include large transition lists while maintaining adequate dwell times by acquiring transitions only around elution windows. 6400 Series with Dynamic MRM
Each Dynamic MRM transition is acquired from Ret Time - 1/2*(Delta Ret Time) to Ret Time + 1/2*(Delta Ret Time), with times entered in minutes. p.37 ↗ Accurate retention time and delta retention time entries are critical to ensure the compound elutes within the acquired window. 6400 Series with Dynamic MRM
Triggered Dynamic MRM allows up to two Trigger MRMs per compound; secondary transitions are acquired only when Trigger MRM abundances exceed thresholds. p.40 ↗ Confirmatory MRMs can be acquired only when needed, preserving dwell time for primary quantitation. 6400 Series with Triggered Dynamic MRM
Trigger Entrance Delay of 2 means if trigger conditions are met at scan 200, only primaries are acquired at scans 201 and 202; primary and secondary transitions start at scan 203. p.42 ↗ Entrance delay can be used to avoid premature acquisition of secondary transitions immediately after threshold crossing. 6400 Series with Triggered Dynamic MRM
Trigger Delay of 1 with Repeats set to 3 and trigger conditions met at scan 200 results in secondary transitions at scans 201, 203 and 205; primaries only at 202 and 204. p.42 ↗ Trigger Delay controls spacing between secondary transition acquisitions, affecting data density for confirmatory ions. 6400 Series with Triggered Dynamic MRM
Trigger Window default is 0, meaning the Trigger Window equals the Peak Retention Time window; the entered value is the full width in minutes. p.43 ↗ Narrowing the Trigger Window restricts threshold monitoring to a sub-window, reducing false triggers from matrix interferences. 6400 Series with Triggered Dynamic MRM
The 6490 and 6495 use two rough pumps and a three-stage turbo pump for the first five vacuum stages; the second turbo pump is on the last stage. p.71 ↗ These models require two roughing pumps to maintain pressure in the dual-stage ion funnel and handle gas load from the curved collision cell. 6490, 6495
The 6470 uses a single roughing pump and three-stage turbo pump for the first four vacuum stages, with a second turbo pump on the fourth stage. p.71 ↗ The 6470 vacuum system is simpler than the 6490/6495 but still uses a second turbo pump for the enhanced collision cell gas load. 6470
The first ion funnel operates at 7 to 14 Torr; the second low-pressure ion funnel operates at 1 to 3 Torr. p.31 ↗ These pressure ranges are characteristic of the iFunnel dual-stage ion funnel and are relevant for vacuum performance verification. 6490, 6495
The 6490A and 6495 resistive capillary has 6 capillary inlets and samples up to 10X more ion-rich gas from the source. p.58 ↗ This design improves ion transmission and sensitivity compared to single-inlet capillaries. 6490A, 6495
Checktune takes approximately 3 to 5 minutes per polarity and verifies peak width and mass axis before acquisition. p.77 ↗ Checktune should be run before acquisition to confirm tuning mix ion masses and response are within expectations. 6400 Series
Autotune takes approximately 15 to 20 minutes per polarity for all models except 6490 and 6495; the 6490 takes approximately 45 minutes per ionization mode and the 6495 approximately 25 minutes per ionization mode. p.77 ↗ Plan maintenance and tuning time accordingly, especially for 6490 which requires the longest Autotune. 6400 Series
Autotune only needs to run after preventative maintenance or if Checktune indicates a problem; Tune from factory default should only be marked if regular Autotune fails or the tune file is corrupted. p.77 ↗ Avoid unnecessary full factory-default tuning; use Checktune as the routine verification step. 6400 Series
The 6495B Gate Valve Technology allows capillary replacement without venting the instrument, using a Capillary Removal Tool and a safety lock. p.28 ↗ Capillary maintenance can be performed without breaking vacuum, increasing uptime and productivity. 6495B
The 6495B mass range is extended to 3000 amu, and the quadrupole driver is improved compared to the 6495A. p.28 ↗ The 6495B covers a wider mass range than the 6495A (5-2250 m/z) for higher-mass analytes. 6495B
The 6470 has a mass range of 5 to 3000 m/z; the 6490 has 5 to 1400 m/z; the 6495 has 5 to 2250 m/z. p.23 ↗ Model selection should consider the required mass range for target analytes. 6470, 6490, 6495
Linear dynamic range is six orders of magnitude for the 6470, 6490 and 6495, and five orders of magnitude for the 6460, 6430 and 6420 (verapamil analysis). p.55 ↗ Higher-end models provide an additional order of magnitude for quantitation across wide concentration ranges. 6400 Series
When the Multimode source is operated in ESI and APCI simultaneously, there can be a loss of sensitivity up to a factor of two for some compounds. p.61 ↗ Weigh the benefit of simultaneous ESI/APCI against potential sensitivity loss; for most applications a loss of less than 2 is negligible. G1978B Multimode Source
The collision region in the single quadrupole between capillary exit and skimmer is at about 2 Torr, approximately three orders of magnitude below atmospheric pressure (760 Torr). p.21 ↗ This pressure regime supports collisionally induced dissociation for fragment ion studies. Single quadrupole (conceptual comparison)
The Data Acquisition program requires at least one window to remain open; Instrument Status, Chromatogram Plot and Spectrum Plot windows can be closed for easier viewing. p.80 ↗ Operators can customize the workspace but must keep at least one window open to maintain control and monitoring. MassHunter Data Acquisition for 6400 Series

Technical Data

Parameter Value Condition
Mass range 5 to 3000 m/z p.23 ↗ 6470
Mass range 5 to 1400 m/z p.24 ↗ 6490
Mass range 5 to 2250 m/z p.24 ↗ 6495
Mass range 3000 amu p.28 ↗ 6495B
Mass range 5 to 2250 m/z p.29 ↗ 6495A
Mass range 5 to 1400 m/z p.32 ↗ 6490
Linear dynamic range six orders of magnitude p.55 ↗ 6470, 6490, 6495 (verapamil)
Linear dynamic range five orders of magnitude p.55 ↗ 6460, 6430, 6420 (verapamil)
Limit of detection and quantitation Femtogram-level p.9 ↗ 6430 and 6460
Limit of detection and quantitation Attogram-level p.9 ↗ 6470, 6490, and 6495
First ion funnel pressure 7 to 14 Torr p.31 ↗ iFunnel dual-stage ion funnel
Second ion funnel pressure 1 to 3 Torr p.31 ↗ iFunnel dual-stage ion funnel
Collision region pressure about 2 Torr p.21 ↗ single quadrupole, between capillary exit and skimmer
Maximum transitions 4000 transitions p.37 ↗ Dynamic MRM
Maximum transitions per MRM table 200 transitions p.37 ↗ Dynamic MRM
Maximum MRM tables 1000+ tables p.38 ↗ Dynamic MRM
Maximum Trigger MRMs per compound two p.40 ↗ Triggered Dynamic MRM
Checktune duration 3 to 5 minutes p.77 ↗ per polarity
Autotune duration 15 to 20 minutes p.77 ↗ all models except 6490 and 6495, per polarity
Autotune duration 45 minutes p.77 ↗ 6490, per ionization mode
Autotune duration 25 minutes p.77 ↗ 6495, per ionization mode