Induztr
Engineering Digest Document Viewer Related Models

Agilent 6400 Series Triple Quadrupole LC/MS System Quick Start Guide

Technical Reference Summary

Covered Models & Document Scope

Covers the Agilent 6400 Series Triple Quadrupole LC/MS system. Supported models in Data Acquisition B.07.00: 6420A, 6430A, 6460A, 6460C, 6490A, 6495A. Supported LC models: 1100, 1200, 1260, 1290, HTS, HTC. The 6490 and 6495 include iFunnel Technology; 6495 supports Unit, Wide and Widest resolutions and does not support Fast Scan autotune.

Section-by-Section Technical Breakdown

pp. 6-11
Step 1. Start the Data Acquisition software

Describes starting the MassHunter Data Acquisition program, the eight main windows, and how to show/hide and dock/float windows. Explains the Instrument Status window color coding and the roles of the Actuals, Chromatogram Plot, Spectrum Plot, Method Editor, Sample Run, Worklist and Tune windows.

  • Double-click the Data Acquisition icon on the Desktop to start the program; software engines start automatically and can be restarted via Acq System Launcher > Start Engines.
  • Up to seven windows can be shown at once; windows can be floated by double-clicking the title bar and docked again.
  • Instrument Status window shows device status as Error, Not ready, Pre-run, Post-run, Running, Injecting, Idle, Offline, or Standby with color coding.
  • Tune window is only visible in the Tune context; Checktune and Autotune reports can be printed via Create Tune Report.
pp. 12-15
Step 2. Prepare the LC modules

Covers switching the LC stream to waste, purging the LC pump, conditioning/equilibrating the column, setting up real-time actuals monitoring, and configuring real-time plot displays. Includes how to set parameter ranges so out-of-limit values turn red.

  • When not acquiring data, switch the LC stream away from the MS ion source to waste via right-click QQQ device > LC > Waste.
  • Purge the LC pump according to the pump User Guide.
  • Type LC parameters and click Apply to download them to the LC; monitor baseline to confirm column equilibration.
  • Actuals can be configured via right-click Actuals list > Setup; numeric parameters can have limits that turn the background red when exceeded.
pp. 16-19
Step 3. Prepare the Triple Quad instrument

Describes performing Checktune, Autotune or Manual Tune, including expected durations, supported ion sources, and corrective actions if Checktune fails. Also covers Fast Scan Autotune limitations and switching the LC stream to MS.

  • Checktune takes approximately 3 minutes per polarity and evaluates mass accuracy and resolution; run it regularly.
  • Checktune can be run with ESI, AJS ESI, MMI and HPLC-Chip sources.
  • If Checktune fails, use Manual Tune: select Peak Width (Unit, Wide, Widest) on MS1 or MS2 tab and click Adjust Gain & Offset, then save the autotune file.
  • Autotune takes approximately 30 minutes per ionization mode (25 minutes for 6490/6495); 6490/6495 Autotune only with AJS ESI source.
  • Fast Scan acquisition is only supported on the 6490 for MS2 Scan and Product Ion scan; not supported on 6495.
pp. 20-26
Step 4. Set up and run an acquisition method

Guides setting up an acquisition method including LC module values, Triple Quad scan types and segments, chromatogram signals, stored instrument curves, DA parameters, method properties, and running interactive samples and worklists. Includes locked/unlocked run modes and Override DA Method behavior.

  • Scan segments table is cleared when Scan Type changes; transitions can be copied and pasted when changing from MRM to Dynamic MRM or Triggered MRM.
  • Fragmentor voltage cannot be set in Acquisition for 6490 or 6495; the tune file value is always used.
  • A Data Analysis method contains acquisition parameters with Qual Automation and/or Quant Automation check boxes marked.
  • Locked mode prevents changing method or sample parameters during a run and prevents overwriting the data file.
  • Worklist can run Acquisition Only, Both Acquisition and DA, or DA Only; Override DA Method column can specify a different DA method.
pp. 27
Step 5 and 6. Review and analyze results

Describes using the Qualitative Analysis program to review results, select precursor/product ions for MRM, find and identify compounds, and perform molecular feature extraction. Describes using the Quantitative Analysis program to set up batches and methods, review Batch-at-a-Glance results, and requantitate using better calibration fits.

  • Qualitative Analysis supports acquisition method development, MRM ion selection, compound finding/identification, and molecular feature extraction.
  • Quantitative Analysis supports batch and method setup for automatic quantitation, Batch-at-a-Glance review, and outlier-based requantitation.
  • Familiarization Guides and online Help provide exercises for both programs.

Key Integration, Operating & Safety Requirements

Specification / Condition Engineering Implication Applies To
Dynamic MRM can monitor up to 4000 MRM transitions. p.1 ↗ Method design must stay within this transition limit when using Dynamic MRM. 6400 Series Triple Quadrupole LC/MS
Checktune takes approximately 3 minutes per polarity. p.3 ↗ Schedule regular Checktune runs; budget about 6 minutes for both polarities. 6400 Series
Autotune takes approximately 30 minutes per ionization mode for all models except 6490 and 6495; 6490 and 6495 take approximately 25 minutes per ionization mode. p.3 ↗ Plan instrument downtime accordingly; Autotune should only be run when necessary. 6400 Series; 6490/6495 exception
Autotune from factory defaults takes approximately 30 minutes per polarity (all models except 6490/6495) or approximately 25 minutes per ionization mode (6490/6495). p.3 ↗ Use Start from Factory Defaults only if normal Autotune fails; allow extra time. 6400 Series; 6490/6495 exception
Checktune can be run with ESI, AJS ESI, MMI and HPLC-Chip sources. p.3 ↗ Source selection must match the installed ion source before Checktune. 6400 Series
For all instruments except 6490 and 6495, Autotune can be run with AJS ESI, MMI, and HPLC-Chip sources; with 6490 and 6495, Autotune only with AJS ESI source. p.3 ↗ 6490/6495 users must use AJS ESI for Autotune; other sources are not supported for Autotune on these models. 6400 Series; 6490/6495
If Checktune fails, select Peak Width (Unit, Wide, or Widest) on the MS1 or MS2 tab and click Adjust Gain & Offset; if successful, save the autotune file. p.3 ↗ This is the first corrective action before running a full Autotune. 6400 Series
Fast Scan acquisition is only supported on the 6490 with MS2 Scan and Product Ion scan; Fast Scan autotune uses Wide (1.2) resolution, Samples = 1, and step size 0.2. p.3 ↗ Do not attempt Fast Scan on other models; for 6495 increase step size to 0.3 m/z for faster scan rate. 6490; 6495
Fragmentor voltage cannot be set in Acquisition for 6490 or 6495; it always uses the value in the tune file. p.4 ↗ Method development for 6490/6495 must manage fragmentor via the tune file, not acquisition parameters. 6490, 6495
The Scan segments table is cleared when the Scan Type is changed; transitions can be copied and pasted from MRM to Dynamic MRM or Triggered MRM. p.4 ↗ Save or copy transitions before changing scan type to avoid losing method data. 6400 Series
Locked mode prevents anyone from changing the method or sample parameters during a run and prevents overwriting the data file in Data Acquisition. p.4 ↗ Use locked mode for regulated or unattended runs to protect data integrity. 6400 Series
System Logbook retention can be set from 1 week to 1 year via Tools > Purge Settings. p.3 ↗ Configure retention to meet laboratory record-keeping requirements. 6400 Series Data Acquisition
When not acquiring data, switch the LC stream to waste via right-click QQQ device > LC > Waste. p.2 ↗ Prevents unnecessary contamination of the MS ion source during column conditioning. 6400 Series with LC
Actuals parameters can be assigned numeric limits; if the value is outside the limits, the background is set to red. p.2 ↗ Use Actuals limits for at-a-glance monitoring of critical MS and LC parameters such as heater and vacuum pressure. 6400 Series Data Acquisition
The 6495 supports Unit, Wide, and Widest resolutions; Fast scan autotune is not supported for the 6495. p.2 ↗ 6495 method development can use all three resolution modes but must not rely on Fast Scan autotune. 6495
The 6490 and 6495 contain iFunnel Technology including Dual Offset Ion Funnel, Agilent Jet Stream Technology, and shorter desolvation assembly with Hexabore Capillary. p.1 ↗ These models provide more efficient ion sampling; method sensitivity expectations differ from other 6400 models. 6490, 6495

Faults & Troubleshooting

Code / Symptom Possible Cause Remedy Note
Checktune fails p.17 ↗ MS parameters outside limits for specified mass accuracy and resolution Use Manual Tune tab: select Peak Width (Unit, Wide, or Widest) on MS1 or MS2 tab based on which resolution failed, click Adjust Gain & Offset; if successful, save autotune file. If Checktune fails again, run Autotune. Step 3, page 17
Autotune fails p.18 ↗ Tune parameters could not be optimized automatically Mark Start from Factory Defaults check box and click Autotune; check progress box for reasons; if still unsuccessful, manually tune or call Agilent service engineer. Step 3, page 18
No reports printed after Autotune p.18 ↗ Autotune did not complete successfully Check progress box in lower right side of Autotune tab for reasons why tune failed; fix problem or call Agilent service engineer with this information. Step 3, page 18
Instrument Status window shows Red p.8 ↗ Error status View System Logbook for logged events and errors via Log icon, Tools > System Logbook Viewer, or taskbar LOG icon. Table 1, page 8; page 19
Instrument Status window shows Yellow p.8 ↗ Not ready status Wait for instrument to become ready; check device status and logbook if persists. Table 1, page 8
Instrument Status window shows Dark gray p.8 ↗ Offline status Check device connection and configuration; reconfigure instrument if LC modules changed. Table 1, page 8

Technical Data

Parameter Value Condition
Maximum MRM transitions (Dynamic MRM) 4000 transitions p.1 ↗ Dynamic MRM
Checktune duration approximately 3 minutes p.16 ↗ per polarity
Autotune duration approximately 30 minutes p.17 ↗ per ionization mode; all models except 6490 and 6495
Autotune duration approximately 25 minutes p.17 ↗ per ionization mode; 6490 and 6495
Autotune from factory defaults duration approximately 30 minutes p.17 ↗ per polarity; all models except 6490 and 6495
Autotune from factory defaults duration approximately 25 minutes p.17 ↗ per ionization mode; 6490 and 6495
Fast Scan step size 0.2 m/z p.18 ↗ 6490 Fast Scan Autotune; Wide (1.2) resolution, Samples = 1
Fast Scan step size 0.3 m/z p.18 ↗ 6495 (Fast Scan not supported; increased step size for faster scan rate)
System Logbook retention period 1 week to 1 year p.19 ↗ Tools > Purge Settings