Nabertherm N 440
Nabertherm N 440 — Chamber kilns.
The N 440 is a 440-litre chamber kiln heated from five sides, achieving a maximum temperature of 1300 °C with a 30 kW three-phase connection. Its 600 × 750 × 1000 mm chamber distinguishes it from the smaller N 300 sibling, offering greater batch capacity for uniform high-temperature treatment. It is intended for industrial heat-treatment processes requiring precise thermal distribution across large loads.
Nabertherm Chamber Kilns up to 1300 °C heated from five sides | Nabertherm Series — Model Comparison & Selection
| Model | Chamber volume, L | Weight, kg | Electrical connection | Max temperature, °C |
|---|---|---|---|---|
| N 440 Current | 440 | 820 | 3-phase | 1300 |
| N 300 | 300 | 450 | 3-phase | 1300 |
Full specifications
| Chamber volume | 440 l |
| Electrical connection | 3-phase |
| Nominal power | 30 kW |
| Inner dimensions (W × D × H) mfr | 600 × 750 × 1000 mm |
| Outer dimensions (W × D × H) mfr | 1000 × 1410 mm |
| Weight | 820 kg |
| Max temperature | 1300 °C |
Description
Construction and series positioning
- The N 440 is a floor-standing chamber kiln with a 440 l working volume, heated from five sides (four walls plus door or hearth) to promote temperature uniformity.
- Inner chamber dimensions are 600 mm wide × 750 mm deep × 1000 mm high; outer dimensions are 1000 mm wide × 1410 mm (height or depth not specified in the source).
- Within the series, the N 440 is the larger alternative to the N 300; it shares the 1300 °C maximum temperature and five-side heating concept but provides 140 l more chamber volume.
- The unit weighs 820 kg and requires a 30 kW three-phase electrical supply.
Thermal behaviour and load considerations
- No digitized curve points are available for this model; temperature uniformity and heating rates must be validated empirically or obtained from Nabertherm application engineering.
- The five-side heating arrangement is intended to reduce thermal gradients in the load, but actual uniformity depends on loading pattern, atmosphere, and controller tuning.
- The 1300 °C maximum temperature is a limit for the chamber lining and heating elements; continuous operation near this limit will affect element life and require appropriate process scheduling.
Control and documentation scope
- The attached controller digest covers Nabertherm series 500 controllers and the MyNabertherm app, including process data storage and AMS2750F instrumentation types; however, the specific controller supplied with the N 440 is not stated in the verified facts.
- Other attached documents (fiber optics glass, foundry, dental) do not apply to this chamber kiln model and should not be used for its integration.
- No certificates or applications are listed for this model in the verified data.
Integration & Operating Notes
The N 440 draws 30 kW from a three-phase connection. Verify that the site distribution board, cable cross-section, and protective devices are rated for the full connected load plus diversity; undersized supply will cause voltage drop, contactor chatter, or nuisance tripping during heat-up.
The kiln weighs 820 kg. Confirm that the installation floor or platform can safely support this concentrated load, especially in upper-floor or mezzanine installations. Allow clearance for door swing and service access; the outer width is 1000 mm.
Operating above 1300 °C will accelerate wear of heating elements and insulation. Process recipes should include a safety margin below this limit, and over-temperature protection should be configured in the controller to trip the heating circuit if the setpoint is exceeded.
The attached controller digest describes Nabertherm series 500 and MyNabertherm app features, but the N 440 order code does not specify a controller. Clarify with the supplier whether a series 500 controller is included or must be ordered separately, and whether AMS2750F instrumentation is required for your process.
Selection & Integration Q&A
Choose the N 440 when your batch requires up to 440 l of chamber volume (600 × 750 × 1000 mm) and you need the same 1300 °C five-side heating. The N 300 offers less capacity; select it only if the smaller chamber fits your load and a lower connected load is acceptable.
The kiln requires a 30 kW three-phase supply. Size the feeder cable and circuit breaker for at least 30 kW continuous, and provide a local isolator. Verify that the site voltage and frequency match the nameplate; no other electrical interface details are given in the verified facts.
The verified documents do not list a maintenance schedule or included accessories. Typically, thermocouples, door seals, and heating elements are wear items; request the N 440 instruction manual and spare-parts list from Nabertherm. A controller may be optional and should be confirmed at order.