Shimadzu NJ Servo Series
Shimadzu ·Made in Japan · In Active Production

Shimadzu NJ Servo Series

Shimadzu NJ Servo Series — Testing machines.

The NJ Servo Series is a servo-hydraulic dynamic testing actuator with a 5 kN force capacity and 100 mm full stroke, driven by a 3-phase 200 V servo amplifier and controlled via the Servo Controller 4830. It delivers up to 72 cm/sec unloaded velocity in single-wave mode and 50 cm/sec continuous sine, making it suited for high-cycle fatigue and dynamic characterization of components and materials.

Full specifications

Core Performance & Functional Specifications
Crosshead travel ±100 mm
Dynamic test force (NJ-1kNV-100) mfr ±1 kN (NJ-1kNV-100)
Static test force (NJ-1kNV-100) mfr ±1 kN (NJ-1kNV-100)
Dynamic test force (NJ-5kNV-100) mfr ±5 kN (NJ-5kNV-100)
Static test force (NJ-5kNV-100) mfr ±5 kN (NJ-5kNV-100)
Dynamic test force (NJ-10kNV-100) mfr ±10 kN (NJ-10kNV-100)
Static test force (NJ-10kNV-100) mfr ±10 kN (NJ-10kNV-100)
Dynamic test force (NJ-20kNV-100) mfr ±20 kN (NJ-20kNV-100)
Static test force (NJ-20kNV-100) mfr ±20 kN (NJ-20kNV-100)
Dynamic test force (NJ-30kNV-100) mfr ±30 kN (NJ-30kNV-100)
Static test force (NJ-30kNV-100) mfr ±30 kN (NJ-30kNV-100)
Test force accuracy mfr ±0.5 % indicated value
Stroke accuracy mfr ±1 % indicated value
Maximum speed at maximum loading mfr 72 cm/sec (5, 10 kN)
L0 (NJ-1kNV-100) mfr 980 mm (NJ-1kNV-100)
L1 (NJ-1kNV-100) mfr 680 mm (NJ-1kNV-100)
L0 (NJ-5kNV-100) mfr 1080 mm (NJ-5kNV-100)
L1 (NJ-5kNV-100) mfr 730 mm (NJ-5kNV-100)
L0 (NJ-10kNV-100) mfr 1260 mm (NJ-10kNV-100)
L1 (NJ-10kNV-100) mfr 750 mm (NJ-10kNV-100)
L0 (NJ-20kNV-100) mfr 1385 mm (NJ-20kNV-100)
L1 (NJ-20kNV-100) mfr 840 mm (NJ-20kNV-100)
L0 (NJ-30kNV-100) mfr 1550 mm (NJ-30kNV-100)
L1 (NJ-30kNV-100) mfr 820 mm (NJ-30kNV-100)
Dimensions, Weight & Mechanical Design
Weight (NJ-1kNV-100) mfr Approx. 30 kg (NJ-1kNV-100)

Description

Construction and positioning

Integration & Operating Notes

Electrical
3-phase 200 V supply must handle 7 kVA inrush

The servo amplifier draws 7 kVA from a 3-phase 200 V source; ensure the supply and circuit protection are sized for the amplifier's inrush current and continuous demand. Undersized supply can cause tripping or unstable actuator motion.

Factory Specification Sheet
Control & I/O
Only Servo Controller 4830 is compatible

The actuator is designed exclusively for the Servo Controller 4830; other controllers may not provide the correct command signals, feedback scaling, or safety interlocks. Verify controller firmware and configuration match the actuator's stroke and force ratings before operation.

Factory Specification Sheet
Process Limits
Continuous sine operation limited to 50 cm/sec unloaded

In continuous sine wave mode, maximum velocity is 50 cm/sec unloaded; single-wave bursts allow 72 cm/sec. Exceeding these limits under load may cause overheating or loss of force accuracy. Amplitude characteristics diagrams must be consulted for loaded conditions.

Factory Specification Sheet

Selection & Integration Q&A

What controller and power supply are required to operate this actuator?

It requires the Servo Controller 4830 and a 3-phase 200 V, 7 kVA supply for the servo amplifier, plus single-phase 100 V, 1.5 kVA for auxiliary circuits. Ensure the supply can deliver the amplifier's inrush current.

Dimensional Drawings & Technical Documentation

Technical documentation

PDF
NJ-SERVO Instruction Manual
Manual ·2,9 МБ ·82 pp.
View PDF
PDF
c225-e030
Datasheet ·10,6 МБ ·12 pp.
View PDF