Induztr
Engineering Digest Document Viewer Related Models

Agilent 6200 Series TOF and 6500 Series Q-TOF LC/MS System Quick Start Guide

Technical Reference Summary

Covered Models & Document Scope

Covers Agilent 6200 Series TOF (6224, 6230) and 6500 Series Q-TOF (6520B, 6530A/B, 6538A, 6540A/B, 6545A, 6550A, 6560A Ion Mobility Q-TOF) LC/MS systems with MassHunter Workstation Software B.07.00; includes source options ESI, Dual ESI, AJS ESI, Dual AJS ESI, Multimode, APPI, APCI.

Section-by-Section Technical Breakdown

pp. 9-14
Step 1. Start the Data Acquisition software

Describes starting MassHunter Data Acquisition, the seven main windows (Instrument Status, Actuals, Chromatogram Plot, Spectrum Plot, Method Editor, Sample Run, Worklist, Tune), window show/hide and float/dock behavior, and the color coding of instrument status. It also explains the Tune window functions and instrument-mode selection for the 6560 Ion Mobility Q-TOF.

  • Double-click the Data Acquisition icon to start; software engines start automatically, or right-click Acq System Launcher and click Start Engines to restart.
  • Instrument Status window color coding: Red=Error, Yellow=Not ready, Purple=Pre-run/post-run, Blue=Running/injecting, Green=Idle, Dark gray=Offline, Light gray=Standby.
  • Tune window: use automated tuning algorithms or manual tune; Agilent recommends manual tuning only for ion source and optics 1, not parameters after the collision cell.
  • For 6560 Ion Mobility Q-TOF, the Tune window contains Acquisition Mode selection (IM-QTOF or QTOF-Only).
  • For 6545 or 6560 Q-TOF, additional small molecule autotune options are available.
pp. 16-18
Step 2. Prepare the LC modules

Covers switching the LC stream to waste during column conditioning/equilibration, purging the LC pump, conditioning the column, and setting up real-time actuals monitoring. It emphasizes monitoring baseline stability before switching flow to the MS.

  • Switch LC Stream to Waste in the Method Editor General tab before conditioning the column; click Apply Now to send only the LC eluent value.
  • Purge the LC pump per the pump User Guide, then condition or equilibrate the column.
  • Set up Actuals window via right-click > Setup to monitor selected instrument parameters with custom colors and conditional formatting.
  • Monitor baseline and adjust plots to confirm column equilibration and stable baseline.
pp. 20-36
Step 3. Prepare the TOF and Q-TOF instrument

Details tuning and calibration procedures for TOF and Q-TOF instruments, including Classic Autotune and SWARM autotune, supported sources per model, tune mix dilution requirements, mass calibration, and switching LC stream to MS. It provides model-specific constraints for instrument mode, mass range, and slicer mode.

  • Tune the instrument after first use, maintenance, service, or pump-down/restart; calibrate mass-axis regularly.
  • Classic Autotune: Set Detector Gain, Standard Tune, or Initial Tune require Instrument Mode = Extended Dynamic Range and Mass Range = Standard (3200 m/z).
  • SWARM autotune (6545/6560): System Tune requires Standard (3200 m/z); Transmission Tune available for Low (1700 m/z) and takes ~6-10 minutes.
  • Supported sources for all autotunes vary by model (see Table 1); nanoESI, Dual nanoESI, HPLC-Chip, MALDI, and GC-QTOF sources cannot run automated tunes.
  • Tune mix dilution: 6530A with Dual AJS ESI or 6540 uses 1:10 diluted for positive TOF tune and 1:40 for negative; 6520B or 6530 with Dual ESI uses undiluted.
  • For 6230 TOF with AJS ESI or Dual AJS ESI, use 1:10 dilution for positive and 1:40 for negative; do not dilute for Dual ESI on 6224 TOF.
  • Recalibrate if Instrument Mode, Mass Range, or Slicer Mode changes, or if calibrant ion abundances exceed ~480,000 (6538/6540) or ~650,000 (other Q-TOF/TOF except 6550).
  • Switch LC stream from Waste to MS after tuning and stable baseline.
pp. 37-38
Step 4. Set up and run a method

Explains setting up MassHunter methods containing acquisition, qualitative, and quantitative parameters, and running single samples or worklists. It covers method options for acquisition only, data analysis only, or both, and references Familiarization Guide exercises.

  • A method can contain acquisition parameters, qualitative analysis parameters, quantitative analysis parameters, or all three.
  • In worklist runs, select Acquisition Only, Both Acquisition and DA, or DA Only in Worklist Run Parameters.
  • Mark Qual Automation or Quant Automation check boxes in the DA tab to run data analysis automatically after acquisition.
  • Set Instrument State tab options in the Tune window before editing or running a method.
  • Use TOF/Q-TOF Familiarization Guide Exercises 1-5 for method setup, IM-QTOF mode, IM-MS optimization, and CCS calculations.

Key Integration, Operating & Safety Requirements

Specification / Condition Engineering Implication Applies To
Classic Autotune Set Detector Gain, Standard Tune, and Initial Tune require Instrument Mode = Extended Dynamic Range and Mass Range = Standard (3200 m/z). p.3 ↗ These autotunes are grayed out if a different mode or source is selected; set these values before tuning. 6200 Series TOF and 6500 Series Q-TOF (Classic Autotune models)
SWARM System Tune requires Mass Range = Standard (3200 m/z); Transmission Tune is available for Low (1700 m/z) and takes approximately 6-10 minutes. p.3 ↗ For small molecule work at Low mass range, use Transmission Tune; System Tune is not available. 6545 and 6560 Q-TOF
For 6530A with Dual AJS ESI or 6540, positive ion TOF tune uses 1:10 diluted tune mix and negative ion TOF tune uses 1:40 diluted tune mix. p.3 ↗ Prepare correct tune mix dilution to avoid autotune failure. 6530A with Dual AJS ESI, 6540
For 6520B or 6530 with Dual ESI, both positive and negative ion TOF tunes use undiluted tune mix. p.3 ↗ Do not dilute tune mix for these configurations. 6520B, 6530 with Dual ESI
For 6230 TOF with AJS ESI or Dual AJS ESI, use 1:10 dilution for positive ion tuning and 1:40 for negative ion tuning. p.3 ↗ Dilution is required for both polarities with AJS sources on 6230. 6230 TOF with AJS ESI or Dual AJS ESI
For 6224 TOF with Dual ESI, do not dilute the tune mix for positive ion tuning; problems occur if diluted. p.3 ↗ Use undiluted tune mix for positive ion tuning on 6224 with Dual ESI. 6224 TOF with Dual ESI
Recalibrate if calibrant ion abundances exceed approximately 480,000 for 6538/6540 Q-TOF or approximately 650,000 for other Q-TOF and TOF instruments (except 6550). p.3 ↗ Dilute the tune calibrant before recalibration to maintain mass accuracy. All TOF/Q-TOF except 6550 (which always uses 1:10 dilution)
Initial Tune duration: up to 60 minutes per polarity for 6538A, 6540A, 6550A Q-TOF; up to 30 minutes per polarity for other Q-TOF and TOF instruments. p.3 ↗ Plan sufficient time for initial tuning based on model. 6200 Series TOF and 6500 Series Q-TOF
Quick Tune takes 7 to 10 minutes; Standard Tune takes 10 to 15 minutes for TOF and 10 to 15 minutes for quadrupole. p.3 ↗ Use Quick Tune for faster limited-parameter tuning; Standard Tune for more parameters. Classic Autotune models
For 6550 Q-TOF small molecule applications, set Quad AMU to 100 in positive polarity and 90 in negative polarity before autotune, and select Low (1700 m/z) mass range. p.3 ↗ Required for proper small molecule tuning on 6550. 6550 Q-TOF
For 6545 or 6560 Q-TOF with Low (1700 m/z) mass range, low mass autotune options include 50-250 m/z and 50-750 m/z (not available for 6560); marking Fragile Ions reduces fragmentor voltage. p.3 ↗ Select appropriate low mass tune for fragile molecules to minimize fragmentation. 6545 and 6560 Q-TOF
Supported sources for all autotunes: 6224 TOF: ESI, Dual ESI; 6230 TOF: ESI, Dual ESI, AJS ESI, Dual AJS ESI; 6520B: ESI, Dual ESI; 6530A/B: ESI, Dual ESI, AJS ESI, Dual AJS ESI; 6538: ESI, Dual ESI; 6540A/B, 6545: ESI, Dual ESI, AJS ESI, Dual AJS ESI; 6550: ESI, Dual ESI, AJS ESI, Dual AJS ESI; 6560: Dual ESI, Dual AJS ESI. p.3 ↗ Automated tunes cannot run with unsupported sources such as nanoESI, MALDI, or GC-QTOF. Per model as listed
For 6545 with Fast Polarity Switching Enabled, only Mass Calibration/Check or FPS System Tune can be run; for TOF and other Q-TOF, only Mass Calibration/Check or FPS Initial Auto Tune. p.3 ↗ Fast Polarity Switching restricts available autotune options. 6545 Q-TOF and other TOF/Q-TOF
Select High Resolution for Slicer Mode before Initial Auto Tune or System Tune for best tuning results. p.3 ↗ High Resolution slicer mode is required for these tunes. All TOF/Q-TOF with slicer mode option
Mass Calibration/Check tune takes a few minutes for TOF and 2 to 5 minutes for the Quadrupole. p.3 ↗ Allow adequate time for calibration checks. All TOF/Q-TOF
For 6530A/B models, the Adjust abundances for optimal calibration feature automatically adjusts fragmentor voltage if calibration masses are outside 50 to 650K range. p.3 ↗ If fragmentor cannot reduce abundance below 650K, dilute calibrant and retry. 6530A/B

Faults & Troubleshooting

Code / Symptom Possible Cause Remedy Note
Autotune can fail p.23 ↗ Tuning mix not diluted for 6560A, 6550A, 6545A, 6540A, or 6530A with Agilent Jet Stream ESI or Dual AJS ESI source. Dilute the tuning mix as instructed in the Installation Guide and online Help. Diluting the ESI-L Tune Mix, page 23
Problems occur if you dilute the tune mix and tune for positive ion p.24 ↗ Diluting tune mix on 6224 TOF with Dual ESI source. Do not dilute the tune mix for the Dual ESI source on the 6224 TOF. TOF section, page 24
Calibration masses detected out of the 50 to 650K range p.25 ↗ Calibrant ion abundance too high or low for optimal calibration. System automatically adjusts fragmentor voltage; if cannot reduce below 650K, dilute the calibrant and retry calibration or autotune. 6530A/B only, page 25
Check tune results are not acceptable p.27 ↗ Mass calibration or tune parameters out of specification. Continue with Transmission Tune (6545/6560) or Quick Tune/Standard Tune/Initial Auto Tune (Classic); if still unacceptable, contact Agilent Field Support. Step 3, pages 27-34
Standard Tune produces unacceptable results p.29 ↗ Tune parameters not optimized. Run an Initial Auto Tune, then adjust Collision Cell Gas Pressure; if still failing, contact Agilent Field Support. Step 3, page 29
System Tune results are not acceptable p.34 ↗ SWARM autotune unable to achieve acceptable performance. Contact your local field service engineer. Step 3, page 34