HiLobe 2703 — product leaflet
Technical Reference Summary
Covered Models & Document Scope
Pfeiffer Vacuum HiLobe vacuum booster series, covering three models: HiLobe 2703, HiLobe 4503 and HiLobe 6203 (nominal pumping speeds 2700/4500/6200 m³/h). Accessories and options include Profinet converter, barrier gas kit (plastic or stainless steel), gear chamber evacuation, spray-lance flushing device, temperature/pressure monitoring, extension cable package, OmniControl, horizontal version, electronic drive variants (box version, switch-cabinet mounting plate, without drive electronics) and cooling options (convection, active-air, water).
Section-by-Section Technical Breakdown
The leaflet highlights reliability via integrated-sensor condition monitoring, high pumping speed with best performance-to-size ratio, and efficiency via hermetically sealed IE5 canned-motor design without shaft seals, variable speed drive and extended maintenance intervals. It lists available accessories, drive and cooling options.
- Intelligent condition monitoring via integrated sensors for high up-time
- Hermetically sealed synchronous motor (IE5), canned motor design, no shaft seals
- Variable speed drive and optimized rotor geometries
- Options: Profinet converter, barrier gas kit (plastic or stainless steel), gear chamber evacuation, spray-lance flushing device
- Options: temperature and pressure monitoring (inlet and exhaust side), extension cable package, OmniControl, horizontal version, operating fluids
- Electronic drive options: box version, mounting plate for switch cabinet integration, without drive electronics
- Cooling options: convection, active-air, water cooling
Pumping speed, rotational speed, differential pressure limits, flange connections and motor/drive electrical data for all three models. All share DN 160 ISO-F / DN 150 PN 16 main and secondary flanges, 380-480 VAC supply and RC 7500 electronic drive unit.
- Nominal pumping speed: 2703: 890-2700 m³/h; 4503: 890-4500 m³/h; 6203: 890-6200 m³/h
- Rotational speed: 2703: 1500-4500 rpm; 4503: 1500-7500 rpm; 6203: 1500-10500 rpm
- Max. differential pressure at max. rotational speed: 2703: 54 hPa; 4503: 36 hPa; 6203: 21 hPa; at min. rotational speed: 65 hPa (all models)
- Main and secondary flanges: DN 160 ISO-F | DN 150 PN 16 (all models)
- Input voltage: 380-480 VAC (±10%), 50/60 Hz; three-phase motor with PTC protection
- Rated power at full rotational speed: 3.5 kW (2703), 5.5 kW (4503), 7.5 kW (6203)
- Electronic drive unit RC 7500; recommended mains fuse 25 A; I/O interfaces PV.can and RS485
Installation and operating limits common to all three models: ambient/shipping temperatures, noise level, operating fluid, protection rating, cooling water requirements, leak rate, dimensions and weight.
- Ambient temperature 5-40 °C; shipping temperature -10-40 °C
- Sound pressure level (EN ISO 2151) at 1 hPa inlet pressure: 60 dB(A) (all models)
- Operating fluid D2, filling volume 1 l
- Protection degree IP54; type 12
- Cooling water: pressure 2000-6000 hPa, flow 120-360 l/h, temperature 5-35 °C
- Integral leak rate 1E-06 Pa m³/s
- Dimensions (L x W x H) 860 x 428 x 354 mm; weight approx. 258 kg (all models)
Key Integration, Operating & Safety Requirements
| Specification / Condition | Engineering Implication | Applies To |
|---|---|---|
| Maximum allowable differential pressure falls with speed: 54 hPa (2703), 36 hPa (4503), 21 hPa (6203) at maximum rotational speed, versus 65 hPa for all models at minimum speed (1500 rpm). p.2 ↗ | For high-pressure-difference pumping, run the booster at reduced speed; at full speed the 6203 tolerates only 21 hPa across it, so the backing pump must hold the exhaust pressure close to inlet pressure. | All models, differential pressure limits model-specific |
| Rotational speed ranges: 1500-4500 rpm (2703), 1500-7500 rpm (4503), 1500-10500 rpm (6203). p.2 ↗ | Speed selection via the variable-speed drive directly scales pumping speed; the 6203 reaches its 6200 m³/h only near 10500 rpm. | Model-specific |
| Both main and secondary flanges are DN 160 ISO-F | DN 150 PN 16 on all models. p.2 ↗ | Inlet and outlet connections are identical, simplifying piping and allowing series stacking with backing pumps. | Whole series |
| Supply voltage 380-480 VAC ±10%, 50/60 Hz; recommended mains fuse 25 A; electronic drive unit RC 7500. p.2 ↗ | Site wiring and breaker sizing can be standardized across all three models; drive electronics must be RC 7500 or ordered without drive for external integration. | Whole series |
| Rated motor power: 3.5 kW (2703), 5.5 kW (4503), 7.5 kW (6203) at full rotational speed. p.2 ↗ | Electrical supply sizing differs per model despite identical fuse recommendation; check motor power when pairing with drive electronics. | Model-specific |
| Motor is a hermetically sealed IE5 synchronous canned motor with no shaft seals. p.1 ↗ | No shaft-seal leaks into the process and reduced maintenance; integral leak rate is 1E-06 Pa m³/s. | Whole series |
| Motor protection via PTC sensors; I/O interfaces PV.can and RS485. p.2 ↗ | PTC must be wired into the drive/control for thermal protection; PV.can/RS485 used for condition monitoring and control integration (Profinet via optional converter). | Whole series |
| Cooling water requirements: pressure 2000-6000 hPa (0.2-0.6 bar relative range), flow 120-360 l/h, temperature 5-35 °C; standard cooling method water cooling. p.2 ↗ | A qualified cooling water loop must be provided; convection and active-air cooling variants are available as options if water is impractical. | Whole series |
| Ambient temperature 5-40 °C, shipping/storage temperature -10-40 °C. p.2 ↗ | Installation spaces below 5 °C require heating; units must not be stored below -10 °C. | Whole series |
| Sound pressure level 60 dB(A) per EN ISO 2151 at 1 hPa inlet pressure for all models. p.3 ↗ | Noise is typically not a limiting factor even for the largest 6203 at high speed; no special acoustic enclosure needed for most installations. | Whole series |
| Operating fluid D2 with 1 l filling volume on all models. p.3 ↗ | Gear/oil chamber service uses Pfeiffer D2 fluid; keep 1 l stock per unit for oil changes; extended maintenance intervals claimed. | Whole series |
| Protection degree IP54, type 12; all three models share identical dimensions 860 x 428 x 354 mm and weight approx. 258 kg. p.3 ↗ | Identical footprint allows model swaps without foundation or enclosure changes; lifting gear for ≥258 kg required; IP54 enclosure suits dusty industrial environments. | Whole series |
| Options include barrier gas kit (plastic or stainless steel), gear chamber evacuation, spray-lance flushing device, and inlet/exhaust temperature and pressure monitoring. p.1 ↗ | For dusty or condensable processes, specify barrier gas and flushing options at ordering time; monitoring sensors enable the integrated condition monitoring strategy. | Whole series (options) |
| Drive electronics can be ordered as box version, as mounting plate for switch cabinet integration, or without drive electronics. p.1 ↗ | Control-cabinet design determines which drive variant to order; cabinet-integrated versions save floor space but require thermal planning. | Whole series (ordering options) |