Induztr
Engineering Digest Document Viewer Related Models

HiScroll 12 — product leaflet

Technical Reference Summary

Covered Models & Document Scope

Pfeiffer Vacuum HiScroll 6, HiScroll 12 and HiScroll 18 dry scroll vacuum pumps (2-page product brochure, dated 13.08.2025). Covers standard models plus options/accessories: tip seal and bearing kits, gas-ballast valve kit, bellows/cover/electronics kits, exhaust silencer, inlet filter, automated vacuum safety valve, OmniControl controller, EtherCAT and Profinet converters, single-phase VSD version (with or without integrated pressure gauge), three-phase version for HiScroll 18, and a C-Version for corrosive gas.

Section-by-Section Technical Breakdown

pp. 1
Features and Benefits

Highlights the pumps' performance against atmosphere with high pumping speeds and short cycle times, plus low noise and vibration suitable for noise-sensitive environments. Claims over 50% lower energy consumption than conventional scroll pumps and fully dry operation without operating fluids.

  • High performance when evacuating against atmosphere; constant pumping speeds and short cycle times
  • Low noise and vibration levels for noise-sensitive working environments
  • More than 50% lower energy consumption compared to conventional scroll vacuum pumps
  • No operating fluids (oil-free/dry) operation required
pp. 1
Accessories, Spare Parts and Options

Lists available spare part kits, accessories and configuration options for the HiScroll series, including maintenance kits, connectivity converters and special gas versions.

  • Maintenance kits: tip seal replacement kit, tip seal and bearing replacement kit
  • Accessories: gas-ballast valve kit, bellows kit, cover kit, electronics kit, exhaust silencer, inlet filter
  • Process protection: automated vacuum safety valve
  • Control/connectivity: OmniControl control device, EtherCAT converter, Profinet converter
  • Electrical variants: single-phase VSD version, single-phase VSD version with integrated pressure gauge, three-phase version for HiScroll 18
  • C-Version: corrosive gas version
pp. 2
Technical Data

Performance table for HiScroll 6, 12 and 18 including pumping speed (with boost mode), ultimate pressures at different gas-ballast settings, power consumption, motor speeds, noise level, weight, dimensions and flange connections. Pumping speed data is for air at 20 °C with ±10% tolerance; curves given for 50 Hz and 60 Hz.

  • Pumping speed: 6.1 / 12.1 / 18.1 m³/h (HiScroll 6/12/18); boost mode: 7.2 / 14 / 21.5 m³/h
  • Ultimate pressure (gas-ballast closed): 0.015 / 0.006 / 0.006 hPa(mbar)
  • Ultimate pressure (gas-ballast open stage 1): 0.07 / 0.05 / 0.05 hPa(mbar); stage 2: 0.4 hPa(mbar) all models
  • Power consumption at ultimate pressure: 165 / 190 / 235 W; at standby speed: 80 / 100 / 100 W
  • Motor speed range: 1000–3000 min⁻¹ (HiScroll 6), 624–1870 min⁻¹ (HiScroll 12/18); nominal 2500 / 1560 / 1560 min⁻¹
  • Sound pressure level (ISO 3744, accuracy grade 2): 48 dB(A) (HiScroll 6), 47 dB(A) (HiScroll 12/18)
  • Weight: 19 / 24 / 23 kg; Dimensions: 380×220×257 mm (HiScroll 6), 419×265×304 mm (HiScroll 12/18)
  • Gas inlet/outlet: DN 25 ISO-KF / DN 25 ISO-KF on all models

Key Integration, Operating & Safety Requirements

Specification / Condition Engineering Implication Applies To
Pumping speed is 6.1 m³/h (HiScroll 6), 12.1 m³/h (HiScroll 12) and 18.1 m³/h, with boost mode speeds of 7.2, 14 and 21.5 m³/h respectively (air at 20 °C, tolerance ±10%). p.2 ↗ Size the pump with ±10% tolerance on curves; use boost mode when faster evacuation/shorter cycle times are needed at the cost of higher power draw. HiScroll 6, 12, 18
Ultimate pressure with gas-ballast valve closed: 0.015 hPa (HiScroll 6), 0.006 hPa (HiScroll 12 and 18). p.2 ↗ For finest vacuum, HiScroll 12/18 reach about 2.5× lower ultimate pressure than HiScroll 6; do not specify HiScroll 6 where <0.01 mbar base pressure is required. HiScroll 6 vs 12/18
With gas-ballast valve open at stage 1, ultimate pressure degrades to 0.07 / 0.05 / 0.05 hPa; at stage 2 it is 0.4 hPa on all models. p.2 ↗ Using gas ballast for vapor handling trades base pressure for condensate tolerance — expect ~0.4 mbar floor at full ballast. All models
Power consumption at ultimate pressure is 165 / 190 / 235 W; at standby speed only 80 / 100 / 100 W. p.2 ↗ Standby speed reduces idle power roughly in half — useful in cyclic processes; enables conservative power supply sizing. All models
Motor speed range is 1000–3000 min⁻¹ (HiScroll 6, nominal 2500 min⁻¹) and 624–1870 min⁻¹ (HiScroll 12/18, nominal 1560 min⁻¹). p.2 ↗ Speeds are variable (VSD-based); match VFD/converter settings to these ranges when integrating with OmniControl or fieldbus options. All models
Sound pressure level is 48 dB(A) for HiScroll 6 and 47 dB(A) for HiScroll 12/18 (ISO 3744, accuracy grade 2). p.2 ↗ Suitable for desk-side/laboratory installation without acoustic enclosures. All models
All models use DN 25 ISO-KF for both gas inlet and outlet. p.2 ↗ Standardize on KF25 hardware (clamps, centering rings, flexible hose/bellows — bellows kit available) for installation. All models
Weights are approx. 19 kg (HiScroll 6), 24 kg (HiScroll 12) and 23 kg (HiScroll 18); footprints are 380×220×257 mm and 419×265×304 mm. p.2 ↗ Single-person handling is feasible; plan bench/cabinet space per these envelope dimensions including clearance for fittings. HiScroll 6 (small frame); HiScroll 12/18 (shared frame)
Consumable maintenance kits exist for tip seals (tip seal kit; tip seal and bearing kit). p.1 ↗ Tip seals are the primary wear item — schedule replacement intervals using the tip seal kit; bearing service requires the combined kit. All models
Optional automated vacuum safety valve is available as an accessory. p.1 ↗ Specify it to protect the pump/system against sudden pressure surges or to isolate the inlet automatically at atmospheric operation. All models
Fieldbus integration via EtherCAT and Profinet converters and the OmniControl control device is offered. p.1 ↗ For automated/remote operation (speed control, monitoring), select the converter matching the plant bus system or run via OmniControl. All models
Single-phase VSD versions (with or without integrated pressure gauge) are standard options; a three-phase version exists for HiScroll 18. p.1 ↗ HiScroll 6/12 can run on single-phase supply via VSD; for HiScroll 18 on three-phase supply, order the dedicated three-phase variant. HiScroll 6/12 (single-phase VSD), HiScroll 18 (three-phase)
A C-Version (corrosive gas version) is available in the HiScroll series. p.1 ↗ For processes with corrosive species, order the C-Version rather than the standard pump to protect internal components. All models (as option)
An inlet filter and exhaust silencer are offered as accessories; gas-ballast valve can be retrofitted via kit. p.1 ↗ Include the inlet filter for particulate-laden processes and the exhaust silencer to further reduce noise; gas ballast can be added later without pump exchange. All models
The pumps operate without any operating fluids (dry scroll principle) and consume over 50% less energy than conventional scroll pumps per manufacturer claim. p.1 ↗ No oil management or oil-mist exhaust handling is needed, simplifying installation and eliminating oil contamination risk in the pumped system; energy savings apply to total cost of ownership calculations. Whole series