Induztr
Engineering Digest Document Viewer Related Models

SmartVane 55 — product leaflet

Technical Reference Summary

Covered Models & Document Scope

Pfeiffer Vacuum SmartVane 55 and SmartVane 70 single-stage oil-lubricated rotary vane vacuum pumps. Document is a 2-page datasheet/brochure covering both variants with technical data, dimensional info, and accessory options.

Section-by-Section Technical Breakdown

pp. 1
Product Highlights

Key selling points of the SmartVane series: leakage-free hermetic design, communication capabilities, and energy efficiency. Mentions dedicated Pfeiffer communication protocol for integration with control devices or mass spectrometer systems, and remote control capability.

  • Leakage-free hermetically sealed pump housing without shaft seals; no oil pan required
  • Long maintenance intervals
  • Dedicated Pfeiffer communication protocol for interaction with control devices or mass spectrometer systems
  • Remote control capability
  • Energy-efficient interior permanent magnet (IPM) motor with standby function
  • Reduced power consumption and low operating costs
pp. 1
Accessories, Spare Parts and Options

Lists available accessories, spare parts and options for the SmartVane pumps. Includes both consumables (oil, filters) and service items.

  • Service kit
  • Dust separator
  • Carbon filter
  • Synthetic oil
  • PFPE oil
pp. 2
Technical Data and Dimensional Drawing

Comparative technical specification table for SmartVane 55 and SmartVane 70, plus dimensional drawing. Pumping speed curve noted as measured with air at 20°C with ±10% tolerance. Covers pumping performance, motor data, acoustics, oil capacity, weight, dimensions, and flange connections.

  • Nominal pumping speed: 31–50 m³/h (SmartVane 55), 31–70 m³/h (SmartVane 70)
  • Ultimate pressure (gas-ballast valve closed): 2·10⁻¹ hPa (mbar) for both models
  • Single-phase motor on both models
  • Nominal motor rating: 0.75 kW (55), 1 kW (70)
  • Nominal motor speed: 800–1350 min⁻¹ (55), 800–1800 min⁻¹ (70)
  • Noise level (50 Hz): <60 dB(A) both models
  • Oil capacity: 1.75 l both models
  • Weight: approx. 36 kg (55), 37 kg (70)
  • Dimensions (L×W×H): 415×312×309 mm (55), 470×312×309 mm (70)
  • Gas inlet DN 40 ISO-F / outlet DN 25 ISO-F both models

Key Integration, Operating & Safety Requirements

Specification / Condition Engineering Implication Applies To
Pump housing is hermetically sealed without shaft seals, eliminating atmospheric leakage paths and removing the need for an oil pan p.1 ↗ Simplifies installation (no oil pan containment needed) and improves base pressure/contamination performance versus conventional shaft-sealed rotary vane pumps whole series
Both variants share the same ultimate pressure of 2·10⁻¹ hPa (mbar) with the gas-ballast valve closed p.2 ↗ Choice between models is driven by pumping speed and motor power, not ultimate pressure; gas-ballast operation will degrade this figure when used for vapor handling whole series
Nominal pumping speed ranges are 31–50 m³/h (SmartVane 55) and 31–70 m³/h (SmartVane 70) p.2 ↗ Variable-speed operation; system sizing must use the lower end of the range at reduced speed/standby, peak figures only at full speed whole series (model-specific ranges)
Pumping speed data is specified for air at 20°C with a ±10% tolerance p.2 ↗ Sizing calculations must include a safety margin; expect up to 10% deviation from published curves whole series
Motors are single-phase with nominal ratings of 0.75 kW (SmartVane 55) and 1 kW (SmartVane 70) p.2 ↗ No three-phase supply required; suitable for lab/standard single-phase outlets, but verify supply circuit rating for the 1 kW model's inrush whole series
Nominal motor speeds are 800–1350 min⁻¹ (SmartVane 55) and 800–1800 min⁻¹ (SmartVane 70); speed control is via the IPM motor p.2 ↗ Standby/idle speed of 800 min⁻¹ reduces power consumption; control speed range must be respected in process integration whole series
Noise level is below 60 dB(A) at 50 Hz for both models p.2 ↗ Suitable for noise-sensitive laboratory environments without acoustic enclosures whole series
Oil capacity is 1.75 l for both models p.2 ↗ Fill quantity for initial commissioning and oil changes; matches service kit consumable planning whole series
Weight is approx. 36 kg (SmartVane 55) and 37 kg (SmartVane 70) p.2 ↗ Two-person handling or lifting equipment recommended for installation whole series
Gas connections are DN 40 ISO-F inlet and DN 25 ISO-F outlet for both models p.2 ↗ Piping and accessories (dust separator, carbon filter, valves) must be specified with matching ISO-F flanges; outlet is one DN size smaller than inlet whole series
Footprint difference is only in length: 415 mm (SmartVane 55) vs 470 mm (SmartVane 70), width and height identical at 312×309 mm p.2 ↗ A common mounting frame/skid can be designed for either model with 55 mm length allowance whole series
PFPE oil is offered as an option alongside synthetic oil p.1 ↗ PFPE enables oxygen-enriched or aggressive-gas applications where hydrocarbon oils are unsuitable; select oil type at ordering stage whole series
Dust separator and carbon filter accessories are available for the inlet/exhaust side p.1 ↗ Specify dust separator for particle-laden processes and carbon filter for oil-mist/odor suppression on exhaust whole series
Pumps support a dedicated Pfeiffer communication protocol for interaction with control devices or mass spectrometer systems, plus remote control p.1 ↗ Allows integration into vacuum system control architecture; plan protocol/connector interface in system wiring design whole series