No photo available yet
Agilent Technologies Feedthroughs for High & Ultra-high vacuum
Agilent Technologies Feedthroughs for High & Ultra-high vacuum — Vacuum technologies.
Agilent feedthroughs for high and ultra-high vacuum are component-level interfaces that pass electrical, motion, or fluid services through a vacuum chamber wall while preserving the pressure boundary. The supplied reference material is a general vacuum formulas and tables booklet, not a model-specific datasheet, so no flange size, leak rate, voltage, or current rating can be stated for this item. Selection must therefore be driven by the chamber flange standard, the service to be passed, and the required base pressure of the system.
Full specifications
| Electron Charge | 1.602 coulomb |
| Molar Volume | 22.41 liters |
| Acceleration due to gravity mfr | 9.8066 |
| Angstrom unit mfr | 10 m |
| Avogadro's number mfr | 6.02214076 |
| Boltzmann's constant mfr | 1.38064852 |
| Equivalent of heat mfr | 4.185 |
| Natural log base mfr | 2.7183 |
| Velocity of light mfr | 2.9979 |
| Velocity of sound mfr | 343 |
| Magnetic flux density mfr | 1 |
| Pressure conversion mfr | 1 Torr |
| Pumping speed conversion mfr | 1 L/s |
| Throughput conversion mfr | 1 cc/sec |
| Outgassing rate mfr | 2 |
| Atomic Mass Unit | 1.6605 grams |
| Standard pressure mfr | 101325 Pa |
Description
Construction and positioning
- The item is a feedthrough, i.e. a sealed penetration for a high-vacuum or ultra-high-vacuum chamber wall; the verified facts contain no series siblings, so no comparison of this modification against neighbouring variants can be made.
- No matched mechanical, electrical, interface, or process-media specifications were returned for this model; the only numeric entries in the record are generic physical constants (for example standard pressure 101325 Pa, pressure conversion 1 Torr) that belong to the reference booklet, not to the feedthrough.
Behaviour under vacuum
- The reference booklet covers conductance formulas, pumping-speed and throughput conversions, outgassing rates, and pump-down calculation; these are the correct tools for estimating the pressure drop and gas load a feedthrough introduces, but the feedthrough's own conductance and outgassing rate are not given in the verified facts.
- Because no curve points, leak-rate class, or temperature limit are available, no statement about bakeout behaviour or operating range can be made from this record.
Installation and operation
- The attached document is a general Agilent vacuum reference (formulas, tables, glossary, DIN 28401 symbols) and contains no installation, connection, or control instructions for this feedthrough; the document digest returned no actionable engineering facts.
- Consequently, mounting torque, flange pairing, pin assignment, and cable specification must be taken from the feedthrough's own instruction sheet, which is not part of the supplied material.
Integration & Operating Notes
The verified record contains no flange designation for this feedthrough, so the mating chamber port cannot be checked from the card. Confirm the flange family and nominal size against the chamber drawing and the feedthrough's own datasheet before mounting; an unmatched flange cannot be sealed and will prevent the system from reaching base pressure.
No voltage, current, or conductor count is recorded for this feedthrough. Do not size cabling, feedthrough wiring, or power-supply insulation from this card; use the conductor rating from the feedthrough's own datasheet and keep the external wiring rated for the highest voltage present on the pins.
The reference booklet describes leak-detection practice but gives no service interval for this component. After any installation or re-sealing, perform a helium leak check on the feedthrough joint before running the process, since a disturbed elastomer or metal seal is the most common source of a new virtual leak.
Selection & Integration Q&A
The verified facts list no sibling models, so no variant comparison can be made. Choose by the service to be passed (electrical, motion, or fluid), the chamber flange standard, and the required base pressure; confirm these three against the feedthrough datasheet before ordering.
The mating flange family and nominal size, the available port orientation, and the chamber's base-pressure target. The verified record gives no flange or leak-rate value, so these must be read from the feedthrough datasheet and matched to the chamber drawing before installation.
No mounting torque, temperature limit, or bakeout cycle is present in the verified facts; the attached document is a general formulas and tables booklet with no installation section. Obtain the feedthrough instruction sheet for torque and thermal limits before bakeout or repeated cycling.
The verified facts contain no delivery scope, cable, connector, or accessory list. Cables, mating connectors, and flange hardware must be confirmed against the feedthrough's ordering information; none of these can be assumed to be included from this record.