No photo available yet
Agilent Technologies 1290 Infinity II LC System
Agilent Technologies 1290 Infinity II LC System — Liquid chromatography.
The 1290 Infinity II LC System is a stackable UHPLC platform built around the G7120A High-Speed Pump (1300 bar, 5 mL/min, 10 µL delay volume) and a choice of Multisampler, Hybrid Multisampler, or Vialsampler. It is distinguished from the Flexible Pump variant by its binary high-pressure gradient and lack of a 4CGV, suiting narrow-bore sub-2 µm separations. Primary purpose: high-resolution, high-throughput liquid chromatography in analytical laboratories.
Full specifications
| Analytical Flow Rate | 5 mL/min |
| Baseline Drift | 1 AU/h |
| Carryover | 9 ppm |
| Data Rate | 240 Hz |
| Maximum Individual Bottle Volume | 2 L |
| Maximum pressure | 1300 bar |
| Maximum System Pressure | 1300 bar |
| Sample Capacity | 6144 samples |
| Solvent Cabinet Maximum Volume | 8 L |
| Delay volume mfr | 10 μl |
| Gradient composition range mfr | 1...99 |
| Number of columns mfr | eight columns columns |
| Sensitivity gain vs conventional flow cells mfr | 10 times |
| Inline filter nominal pore size mfr | 0.3 μL |
| Purge flow rate mfr | 2.5...3 mL/min |
| Seal wash solvent mfr | 10 water |
| Default IP address mfr | 192.168.254.11 |
| Delay volume (High-Speed Pump) mfr | 10 μl |
| Gradient composition range (High-Speed Pump) mfr | 1...99 |
| Number of columns in MCT mfr | eight columns columns |
| Sensitivity gain vs conventional flow cells (DAD) mfr | 10 times |
| Red mfr | 0.12 mm |
| Green mfr | 0.17 mm |
| Blue mfr | 0.25 mm |
| Orange mfr | 0.50 mm |
| Double mfr | 7116 A/B |
| Single mfr | 7114 A/B |
| Flow Cell Path Length | 60 mm |
| Capillary inner diameter mfr | 0.12 mm |
| Capillary inner diameter (red) mfr | 0.12 mm |
| Capillary volume per length (red) mfr | 0.113 cm |
| Capillary inner diameter (green) mfr | 0.17 mm |
| Capillary volume per length (green) mfr | 0.227 cm |
| Capillary inner diameter (blue) mfr | 0.25 mm |
| Capillary volume per length (blue) mfr | 0.491 cm |
| Capillary inner diameter (orange) mfr | 0.50 mm |
| Column Compartment Temperature | 80 °C |
| Column thermostatting range mfr | 20...110 °C |
| Detector noise mfr | 0.6 μAU/cm |
| Column thermostatting cooling mfr | 20 °C |
| Column thermostatting heating mfr | 110 °C |
| Detector noise (DAD) mfr | 0.6 μAU/cm |
| Detector noise (VWD) mfr | 1.5 μAU |
Description
Architecture and series positioning
- The system is a modular stack: pump (G7120A High-Speed Pump or G7104A Flexible Pump), sampler (G7167B Multisampler, G7137B Hybrid Multisampler, or G7129B Vialsampler), column thermostat (G7116B MCT), detector (G7117B DAD, G7123B FLD, or G7114B VWD), and solvent cabinet or G7175A Level Sensing.
- This card describes the High-Speed Pump configuration: a binary high-pressure gradient pump with 1300 bar maximum pressure, 5 mL/min analytical flow, 10 µL delay volume, and 1–99% gradient range. The 4CGV gradient valve is available only on the Flexible Pump, not on the High-Speed Pump.
- The Multisampler and Hybrid Multisampler both accommodate up to 6144 samples within the standard stack footprint; the Vialsampler is the lower-capacity alternative with an optional integrated column compartment (up to 80 °C, sample thermostat 4–40 °C).
Behavior under load and separation performance
- The High-Speed Pump's 10 µL delay volume and 1–99% gradient range support fast gradients and short run times; the 1300 bar ceiling is intended for narrow-bore columns and sub-2 µm particles.
- The G7117B DAD uses a 60 mm Max-Light cartridge cell with typical noise below ±0.6 µAU/cm and up to 10× higher sensitivity than conventional flow cells; sampling rates up to 240 Hz support fast separations. The G7114B VWD offers noise below ±1.5 µAU and baseline drift below 1·10⁻⁴ AU/h at data rates up to 240 Hz.
- The G7116B MCT provides cooling down to 20 °C below ambient and heating up to 110 °C, with exchangeable ultra-high-pressure valves for selection from eight columns, sample preparation, and alternating column regeneration.
- Multisampler carryover is reduced to less than 9 ppm with multi-wash; the Hybrid Multisampler adds standard flow-through and Agilent Feed Injection modes plus optional compressor-based thermostatting and a biocompatible sample flow path.
Installation, connection, and control
- Modules are stackable; configurations include a single stack of maximum four modules, two stacks, InfinityLab Flex Bench, or InfinityLab Benchtop, chosen to minimize delay volume in the flow path.
- LAN configuration is executed from the module with direct LAN connection to the controller software, which must be the module with the highest data rate, usually the detector. Rear DIP switches set addressing: all DOWN = default IP 192.168.254.11; switch 4 UP = DHCP; switch 5 UP = STORED address. MAC address is usable only in DHCP mode.
- Lab Advisor is used to add the system by instrument name, address (IP, host name, or COM port), and instrument type. The InfinityLab LC Performance Check is run after complete installation to confirm all modules function and are connected correctly.
- Standard capillary setup is documented with color-coded properties: red 0.12 mm ID = 0.113 µL/cm; green 0.17 mm ID = 0.227 µL/cm; blue 0.25 mm ID = 0.491 µL/cm; orange 0.50 mm ID. Select ID and length to minimize delay volume and dispersion.
- The leak plane catches internal liquid leaks, guides them to the leak sensor, and passes them to the next module below if the sensor fails; the leak sensor stops the running system when the detection level is reached. Drain connectors: Double Drain Connector (5043-1836) on the MCT, Single Drain Connectors (5043-1834) on other modules, excluding the bottom module.
Integration & Operating Notes
Dimethylformamide is incompatible with the PVDF leak sensor material and leads to corrosion. Do not use DMF as mobile phase; check the leak sensor regularly for corrosion and do not place metal parts on the leak panel or sensor.
LAN configuration is executed from the module with direct LAN connection to the controller software, which must be the module with the highest data rate, usually the detector. Rear DIP switches set addressing: all DOWN = default IP 192.168.254.11; switch 4 UP = DHCP; switch 5 UP = STORED address. MAC address is usable only in DHCP mode.
Plan mobile phase volumes and bottle sizes to stay within the 8 L total cabinet capacity and 2 L per-bottle limit. Use only HPLC-grade solvents and water filtered through 0.2 µm filters; exchange water-based solvents daily and use solvent volume within 1–2 days.
The Purge function fills the pump, exchanges solvent, and removes air bubbles. Purge each channel with fresh solvent at 2.5–3 mL/min for 5 min before operation, then equilibrate the system. Conditioning is used daily when starting the pump and to minimize pressure ripple.
Change seal wash solvent (10% isopropanol in water) and bottle weekly; do not recycle seal wash solvent. Seal Wash extends seal lifetime when using buffers with elevated salt concentrations or volatile solvents with non-volatile additives.
The optional inline filter (5067-5407, stainless steel) has a nominal filter pore size of 0.3 µL, very small internal volume, is specified for high pressures, and can be back-flushed. It is recommended to protect the downstream system from blockages, for solvent combinations that can form precipitation, and for buffer applications; back-flush weekly.
Install the Double Drain Connector (5043-1836) on the Multicolumn Thermostat and Single Drain Connectors (5043-1834) on other modules, excluding the bottom module, which must be connected via waste tubing. Drain connectors improve leak drainage for low-flow leaks of high-viscosity solvents.
Agilent recommends the 6 L waste can with 1 Stay Safe cap GL45 with 4 ports (5043-1221) for safe waste disposal. If using a custom waste solution, tubes must not immerse in the liquid, and waste flow must not be restricted at bends or joints.
Selection & Integration Q&A
Pick the High-Speed Pump (G7120A) for binary high-pressure gradients with narrow-bore columns and sub-2 µm particles: 1300 bar, 5 mL/min, 10 µL delay volume, 1–99% gradient. The Flexible Pump (G7104A) adds the 4CGV gradient valve for low-pressure mixing and buffer channels; the 4CGV is not available on the High-Speed Pump.
Connect the LAN cable to the module with the highest data rate, usually the detector, and run LAN configuration from that module. Set rear DIP switches: all DOWN = 192.168.254.11; switch 4 UP = DHCP; switch 5 UP = STORED. MAC address is usable only in DHCP mode. Add the system in Lab Advisor by name, address, and type.
The system can be installed as a single stack of maximum four modules, two stacks, an InfinityLab Flex Bench, or an InfinityLab Benchtop, chosen to minimize delay volume. Install drain connectors on all modules except the bottom one, which uses waste tubing. The leak sensor stops the system when the detection level is reached, so ensure leak plane outlets and waste tubes are unrestricted.
Daily: replace water/buffer solvents, check seal wash, purge each channel at 2.5–3 mL/min for 5 min, equilibrate. Weekly: change seal wash solvent (10% isopropanol in water) and inspect solvent filters; back-flush the optional inline filter (5067-5407). Recommended accessories not in base delivery: 6 L waste can 5043-1221, drain connectors 5043-1836/5043-1834, and the HPLC System Tool Kit.