Agilent Technologies 6495D LC MS
Agilent Technologies 6495D LC MS — Liquid chromatography.
The Agilent 6495D is a triple quadrupole LC/MS detector for the Ultivo/6475A/6495D series, distinguished by 6495D-only Configure Tune, Advanced Tune, and Diagnostic Tune. It operates in 15–35 °C labs and serves as the MS detector in LC/MS workflows with ESI, AJS ESI, APCI, MMI, or Nanospray sources.
Full specifications
| Maximum operating pressure | 250 PSIG |
| Software revision mfr | 12.1 higher |
| Steam cleaning LC pump flow mfr | 0.5 ml/min |
| Steam cleaning nebulizer pressure mfr | 60 psi |
| Steam cleaning drying gas flow mfr | 13 L/min |
| Nebulizer flush flow rate mfr | 1 minute |
| Nebulizer flush duration mfr | 3...5 minutes |
| MS40+ oil mist filter distance from cap threads mfr | 2 cm |
| Diagnostic tune duration mfr | 3 hours |
| Maximum manual instrument modes mfr | ten ten |
| ESI mfr | ESI-L Low Concentration Tuning Mix Mix |
| AJS ESI mfr | ESI-L Low Concentration Tuning Mix Mix |
| MMI mfr | MMI-L Low Concentration Tuning Mix Mix |
| APCI mfr | APCI-L Low Concentration Tuning Mix Mix |
| Microflow Nebulizer Assembly mfr | 0.003 inch |
| Tested ESI Nebulizer Assembly (older style) mfr | 0.003 inch |
| Maximum flow rate mfr | 8 minute |
| Gas source supply pressure mfr | 10...15 psi |
| Line voltage fuse rating mfr | 8 amp |
| Operating temperature | 15...35 °C |
| Storage temperature | -40...70 °C |
Description
Series positioning and 6495D-specific architecture
- The 6495D shares the Ultivo/6475A/6495D hardware platform (front/rear views, status LEDs, CDS bottle, foreline pump, 8 A fuses, LAN/serial ports) but is the only model with Configure Tune, Advanced Tune, and Diagnostic Tune.
- Up to ten manual Instrument Modes can be configured; manual modes cannot be validated by checktune or autotune, and at least one Standard Quadrupole polarity must remain enabled.
- Access to Configure Tune and Advanced Tune requires the Manual Tune privilege in OpenLab Control Panel.
Behavior under tuning and acquisition modes
- Routine verification uses checktune (peak width and mass axis); autotune is reserved for after preventative maintenance or a failed checktune.
- Diagnostic Tune (6495D only) runs approximately 3 hours, requires sufficient tune solution in the CDS bottle, and is intended only after autotune failure; it produces a TCDBackup.zip log for Agilent service.
- Tuning mix is source-specific: ESI-L (G1969-85000) for ESI/AJS ESI, MMI-L (G1969-85020) for MMI, APCI-L (G1969-85010) for APCI; wrong mix causes miscalibration.
- Standby keeps the source interface on and drying gas heated while source/ion optics voltages are off; venting turns off spray chamber HV, heaters, collision gas, nebulization, and detector, with the rough pump stopping below a turbo speed threshold.
Installation, control and operation
- MassHunter 12.1 or higher is required; the System Activity Log in the Data Acquisition ribbon is the first troubleshooting reference.
- When changing scan type (MRM to Dynamic/Triggered MRM), transitions can be copied between scan segment tables; running acquisition plus data analysis requires an Override DA method.
- Steam cleaning setpoints: LC pump 0.5 ml/min, nebulizer 60 psi, drying gas 13 L/min at 350 °C; overnight steam cleaning improves signal-to-noise.
Integration & Operating Notes
Configure Tune and Advanced Tune are inaccessible unless the Manual Tune privilege is enabled in OpenLab Control Panel; set user permissions before attempting 6495D tuning workflows to avoid blocked access.
Lower drying gas temperature to minimum and, for APCI/multimode, vaporizer heater to minimum, then wait 20 minutes to prevent burns from the high-temperature spray chamber before cleaning the spray shield.
Oil should be replaced every six months or sooner if dark/cloudy, filled to the maximum sight-glass level; the oil mist filter must sit no more than 2 cm from outside the cap threads.
ESI/AJS ESI requires ESI-L (G1969-85000), MMI requires MMI-L (G1969-85020), APCI requires APCI-L (G1969-85010); the wrong mix can cause miscalibration and mass assignment errors.
Refill when tuning mix is within a few millimeters of the intake tube end; rinse once with water then twice with ACN, and label the bottle with the tuning mix expiration date to prevent calibrant delivery failure.
Selection & Integration Q&A
Pick the 6495D when you need Configure Tune, Advanced Tune, and Diagnostic Tune (6495D-only) and up to ten manual Instrument Modes. Choose Ultivo or 6475A if those advanced tuning workflows are not required; the manual covers all three on shared hardware.
MassHunter 12.1 or higher is required. Match the tuning mix to the installed source: ESI-L G1969-85000 for ESI/AJS ESI, MMI-L G1969-85020 for MMI, APCI-L G1969-85010 for APCI. Enable Manual Tune privilege in OLCP for advanced tuning.
Operate only within 15–35 °C; storage is -40 to 70 °C. Diagnostic Tune occupies about 3 hours and should follow autotune failure. Standby keeps source warm with voltages off; full venting is required before shutdown to protect the turbo pump.
Daily/weekly spray chamber cleaning (50:50 LC/MS IPA:water), weekly nebulizer flush (30–70% methanol, ≤1 ml/min, 3–5 min), quarterly rough pump oil check, six-month MS40+ oil/filter change with AVF 60 Gold, plus source-specific tuning mixes and calibrant refills.