Eppendorf Varispenser ® 2/ Varispenser ® 2x
Eppendorf Varispenser ® 2/ Varispenser ® 2x — Pipettes.
The Eppendorf Varispenser 2 / Varispenser 2x is a mechanical positive-displacement bottle-top dispenser offered in six volume ranges from 0.2–2 mL to 10–100 mL, with the 0.2–2 mL variant using 0.05 mL increments. It mounts on GL 45 bottles via adapters for GL 25, GL 28, GL 32, GL 38 and S²40, and the dispensing unit is autoclavable. It is used for repetitive, contamination-sensitive dispensing from a reservoir bottle.
Full specifications
| Autoclavable | yes |
| Operating Mode | mechanical |
| Pipetting Type | Positive displacement system |
| Pipetting volume | 0.2...2 mL |
| Random Measurement Error 1) | 0.2 µL |
| Systematic Measurement Error 1) | 0.2 µL |
| Volume Increment | 0.05 mL |
| Number Of Channels | 1 |
Description
Construction and series positioning
- Single-channel, mechanical positive-displacement bottle-top dispenser; no electrical supply or control interface is required.
- The series spans six volume ranges: 0.2–2 mL, 0.5–5 mL, 1–10 mL, 2.5–25 mL, 5–50 mL and 10–100 mL. The 0.2–2 mL range is the smallest of the line and is the only one listed with a 0.05 mL volume increment.
- Two product variants exist: Varispenser 2 (order nos. 4966 000 010 / 029 / 037 / 045 / 053 / 061) and Varispenser 2x (order nos. 4967 000 014 / 022 / 030 / 049 / 057 / 065). Each order number corresponds to one volume range; the facts do not state which order number maps to which range, so the mapping must be taken from the order table.
- Bottle connection is GL 45 as standard, with adapters for GL 25, GL 28, GL 32, GL 38 and S²40.
Dispensing behavior
- Positive displacement means the dispensed volume is set by the mechanical stroke of the piston, not by gravity or air displacement; the stated accuracy figures for the 0.2–2 mL range are 0.2 µL systematic and 0.2 µL random error.
- Volume is adjustable in 0.05 mL steps across the 0.2–2 mL range.
- No digitized curves or load-dependent behavior data are provided; performance under different liquids or viscosities is not documented in the supplied facts.
Installation and operation
- The unit screws onto the bottle thread; the correct adapter must be selected for non-GL 45 bottles.
- The dispensing unit is autoclavable, so it can be sterilized between media changes.
- No electrical connection, control signal or software is involved; operation is entirely manual.
Integration & Operating Notes
The dispenser mounts directly on GL 45 bottles. For GL 25, GL 28, GL 32, GL 38 or S²40 bottles the corresponding adapter is required; fitting the wrong adapter prevents a sealed, vertical mount and can cause leakage or tipping of the filled bottle.
The dispensing unit is autoclavable. Sterilize it when switching between media or after contamination-sensitive work; the supplied facts do not give a maximum autoclave temperature or cycle count, so the autoclave program must be confirmed against the unit's own instructions before the first cycle.
Selection & Integration Q&A
Pick the 0.2–2 mL range when dispensing volumes below 2 mL in 0.05 mL steps with 0.2 µL systematic and random error. For volumes above 2 mL, move to the 0.5–5 mL or larger order numbers; the range is fixed per unit and cannot be adjusted upward.
The standard connection is GL 45. For GL 25, GL 28, GL 32, GL 38 or S²40 bottles, the matching adapter must be ordered; no electrical supply, drive or controller is needed because the unit is mechanical.
Yes, the dispensing unit is autoclavable. This allows sterilization between media changes; the supplied facts give no maximum autoclave temperature or cycle limit, so confirm the autoclave program against the unit's instructions before the first cycle.
The base unit ships with the GL 45 connection; adapters for GL 25, GL 28, GL 32, GL 38 and S²40 are separate items. No electrical cables or controllers apply, since the dispenser is purely mechanical.