Operating Instructions — VCS 200 vacuum pump (BA 236-EN, ed. 1.7 28/06/2022, EN)
Technical Reference Summary
Covered Models & Document Scope
Este documento abarca las bombas de vacío rotativas de paletas lubricadas con aceite V-VCS 200 | 300 (diseño estándar) y V-VCX 200 | 300 (mayor compatibilidad con vapor de agua). Ambas tamaños (200 y 300) están cubiertos en ambas variantes. La variante V-VCX incorpora además piezas funcionales más resistentes al vapor de agua y disolventes, paletas de resina epoxi reforzada con fibra de vidrio, mayor cantidad de lastre de gas y una válvula de lastre de gas ajustable con válvula de bola.
Section-by-Section Technical Breakdown
Describe la construcción y el principio de funcionamiento de las bombas de vacío rotativas de paletas lubricadas con aceite de una etapa. Los componentes principales incluyen la conexión de vacío, la brida de entrada con válvula antirretorno, el elemento separador de aceite, la válvula de lastre de gas, el visor de aceite y las trayectorias del aire de refrigeración. La variante V-VCX tiene mayor compatibilidad con vapor de agua y una válvula de lastre de gas ajustable.
- Single-stage oil-flooded rotary vane design with integrated mesh filter on suction side and oil mist separator on outlet side.
- Integrated non-return valve prevents the evacuated system from being ventilated after pump stop for approx. 2 minutes.
- Standard gas ballast valve prevents condensation of low quantities of water vapour when at operating temperature.
- V-VCX variant: functional parts more resistant to water steam and solvents, glass-fibre reinforced epoxy resin slide gates, increased gas ballast quantity, higher oil sump temperature.
- V-VCX includes an additional adjustable gas ballast valve with ball valve for variable gas ballast capacity.
Define los rangos de presión de admisión admisibles para funcionamiento continuo y la capacidad de aspiración nominal. También proporciona orientación sobre la evacuación de sistemas cerrados, la selección del motor para presiones de admisión más altas y los límites de frecuencia de conmutación.
- Nominal suction power with unrestricted suction: 200 and 300 m³/h at 50 Hz.
- Continuous vacuum intake pressure ranges: V-VCS 0.5 to 500 mbar (abs.); V-VCX 3.0 to 500 mbar (abs.).
- When evacuating closed systems, the volume to be evacuated must be no more than 2% of the nominal pumping capacity.
- For continuous operation > 100 mbar (abs.), the next higher motor output should be used.
- Frequent switching (approx. 10 times per hour) or high ambient/inlet temperatures may exceed motor winding and bearing temperature limits.
Cubre la preparación de la instalación, la instalación mecánica, la conexión de tuberías, la comprobación del nivel de aceite y la conexión del motor. Especifica los requisitos de espacio, los límites de temperatura ambiente, las distancias libres para el aire de refrigeración, la contrapresión admisible y los requisitos de conexión eléctrica.
- Machine must be set up horizontally with max. inclination 1° in all directions.
- Provide at least 50 cm space around the machine for maintenance work.
- Cooling air inlets and outlets must be at least 30 cm away from adjacent walls.
- Ambient temperature: min. +12 °C, max. +40 °C.
- Exhaust air side counter pressure only permissible up to +100 mbar.
- No filter may be installed on the exhaust air side; exhaust air opening must not be closed or restricted.
- For parallel operation, an external non-return valve must be installed in the suction line upstream of each pump.
- Motor electrical data: protection class IP 55, insulation class F, permissible tolerances ±5% voltage deviation and ±2% frequency deviation.
- Electrical installation must be carried out by a qualified electrician observing EN 60204; motor must be safeguarded via a motor protection switch.
Describe las comprobaciones de arranque, la verificación del sentido de giro, la comprobación del nivel de aceite durante el funcionamiento, los procedimientos de parada, la puesta fuera de servicio, el almacenamiento y la puesta en marcha de nuevo. Enfatiza las comprobaciones de seguridad antes de la primera puesta en marcha.
- Installation check must confirm no transport damage, safe horizontal standing, correct pipe connections, tight screw/flange connections, and complete electrical installation.
- Direction of rotation of the motor must correspond with the direction of rotation arrow on the motor flange.
- Oil level must be checked through the oil sight glass and topped up if necessary.
- For standstill times longer than two minutes, vent the connected suction line to atmospheric pressure.
- Decommissioning and storage procedures are specified; recommissioning requires repeating start-up checks.
Proporciona la tabla de mantenimiento, los procedimientos para la limpieza de la bomba de vacío y los filtros, las especificaciones del aceite lubricante y el cambio de aceite, la sustitución del elemento separador de aceite, el mantenimiento del enfriador de aceite y del ventilador, la inspección del motor y del acoplamiento, y la información sobre piezas de repuesto.
- Maintenance table defines intervals for inspection and maintenance works.
- Mesh filter in suction flange and filter cartridge of gas ballast valve must be cleaned.
- Lubricating oil must comply with ISO VG 100 as per DIN ISO 3448.
- Oil separator elements must be changed when dirty.
- Oil cooler and fan must be cleaned; fan renewed if necessary.
- Coupling and coupling sleeve must be checked and replaced if defective or worn out.
- Repairs only allowed by authorised workshops using original spare parts.
Contiene una tabla de fallos con síntomas, causas y remedios. Cubre disparos del interruptor de protección del motor, capacidad de bombeo insuficiente, no alcanzar la presión final, sobrecalentamiento, niebla de aceite en el aire de escape, ruidos extraños y agua en el aceite lubricante.
- Never put the pump back into operation after automatic shut-off without finding and remedying the cause.
- Motor protection switch may trip due to incorrect mains voltage/frequency, incorrect terminal board connection, incorrect switch setting, cold oil, dirty oil separator elements, or excessive back pressure.
- Insufficient pumping capacity can be caused by too long/narrow inlet pipe, leaks, dirty intake filter, or cold/too viscous oil.
- Final pressure not reached due to leaks, incorrect oil viscosity, or dirty oil separator elements.
- Overheating due to high ambient/inlet temperatures, obstructed cooling air, soiled oil cooler, or too viscous oil.
- Visible oil mist in exhaust air due to incorrectly inserted oil separator elements, missing O-rings, unsuitable oil, or dirty separator elements.
- Strange noises may indicate worn pump housing, vibrating vacuum adjustment valve, damaged blades, cold oil, too viscous oil, or defective coupling.
- Water in lubricating oil requires installation of a water interceptor upstream or increased gas ballast.
Remite al capítulo 10 para los datos técnicos, incluidos peso, nivel de presión sonora y otros parámetros de rendimiento. La tabla de datos real no está incluida en el texto proporcionado.
- Technical data are provided in chapter 10 of the manual.
- Data sheet D236 contains technical data and characteristic curves.
- Sound pressure level is specified in chapter 10.
Key Integration, Operating & Safety Requirements
| Specification / Condition | Engineering Implication | Aplica a |
|---|---|---|
| La potencia de aspiración nominal con aspiración sin restricciones es de 200 y 300 m³/h a 50 Hz. p.16 ↗ | Select pump size based on required pumping speed at 50 Hz; 60 Hz data available on data plate. | V-VCS 200/300 and V-VCX 200/300 |
| Rangos de presión de admisión de vacío continuo: V-VCS 0,5 a 500 mbar (abs.); V-VCX 3,0 a 500 mbar (abs.). p.16 ↗ | Operation outside these ranges risks oil leaking through the outlet opening. | V-VCS and V-VCX variants respectively |
| Al evacuar sistemas cerrados, el volumen a evacuar no debe ser superior al 2 % de la capacidad de bombeo nominal de la bomba de vacío. p.16 ↗ | Size the evacuated volume accordingly to avoid operational issues. | Whole series |
| Para funcionamiento continuo > 100 mbar (abs.), debe utilizarse la siguiente potencia de motor superior. p.16 ↗ | Motor selection must account for higher intake pressures to avoid overheating. | Whole series |
| La temperatura ambiente y la temperatura de entrada deben estar entre 12 y 40 °C. p.8 ↗ | Installation location must maintain this temperature range; contact manufacturer for outside range. | Whole series |
| La contrapresión admisible en el lado del aire de escape es de hasta +100 mbar. p.18 ↗ | Exhaust piping must be sized to avoid exceeding this limit; no filters on exhaust side. | Whole series |
| La máquina debe instalarse horizontalmente con una inclinación máxima de 1° en todas las direcciones. p.17 ↗ | Mounting surface must be plane and even; secure against tipping. | Whole series |
| Las entradas y salidas de aire de refrigeración deben estar al menos a 30 cm de paredes adyacentes. p.17 ↗ | Ensure sufficient clearance for cooling air flow to prevent overheating. | Whole series |
| Debe preverse un espacio mínimo de 50 cm alrededor de la máquina para trabajos de mantenimiento. p.17 ↗ | Installation layout must allow access for maintenance and pipe removal. | Whole series |
| Clase de protección del motor IP 55, clase de aislamiento F; desviación de tensión admisible ±5 %, desviación de frecuencia ±2 %. p.19 ↗ | Verify mains supply quality and motor data plate before connection. | Whole series |
| El aceite lubricante debe cumplir con ISO VG 100 según DIN ISO 3448. p.26 ↗ | Use only recommended oil types; incorrect viscosity can cause overheating or insufficient vacuum. | Whole series |
| Para el funcionamiento en paralelo de varias bombas, debe instalarse una válvula antirretorno externa en la línea de aspiración aguas arriba de cada bomba. p.18 ↗ | Prevents damage to a switched-off pump from operating pumps. | Whole series |
| Para tiempos de parada superiores a dos minutos, ventile la línea de aspiración conectada a la presión atmosférica. p.18 ↗ | Provide an air release position (e.g., ball valve) in the suction line. | Whole series |
| Rango de temperatura de almacenamiento: -10 °C a +60 °C; humedad relativa del aire máx. 80 %; almacenamiento no superior a 6 meses. p.13 ↗ | Long-term storage (>3 months) requires preservation oil instead of operating oil. | Whole series |
| Se aprecia una reducción de la potencia cuando se instala a más de 1000 m sobre el nivel del mar. p.17 ↗ | Contact manufacturer for high-altitude installations. | Whole series |
| La conmutación frecuente a intervalos regulares de aproximadamente 10 veces por hora o temperaturas ambiente/de entrada más altas pueden superar los límites de temperatura del devanado del motor y de los rodamientos. p.16 ↗ | Contact manufacturer for such operating conditions. | Whole series |
Faults & Troubleshooting
| Código / Síntoma | Possible Cause | Remedy | Note |
|---|---|---|---|
| Machine is switched off by the motor protection switch p.33 ↗ | Mains voltage/ Frequency does not correspond with the motor data | Check by qualified electrician | Chapter 5.5 |
| Machine is switched off by the motor protection switch p.33 ↗ | Connection to motor terminal board is not correct | Check by qualified electrician | Chapter 5.5 |
| Machine is switched off by the motor protection switch p.33 ↗ | Motor protection switch is not set correctly | Check by qualified electrician | Chapter 5.5 |
| Machine is switched off by the motor protection switch p.33 ↗ | Motor protection switch is triggered too quickly | Use a motor protection switch with an overload-dependent delayed switch off that takes into consideration the short term excess current at start up (version with short circuit and overload trigger as per IEC 60947-4-1) | |
| Machine is switched off by the motor protection switch p.33 ↗ | Vacuum pump or its oil is too cold | Note the ambient temperature and the inlet temperature | Chapter 2.4 |
| Machine is switched off by the motor protection switch p.33 ↗ | The lubricating oil is too viscous | The oil viscosity must comply with ISO VG 100 as per DIN ISO 3448 | Chapter 7.6 |
| Machine is switched off by the motor protection switch p.33 ↗ | The air oil separator elements are dirty. | Change the oil separator elements | Chapter 7.7 |
| Machine is switched off by the motor protection switch p.33 ↗ | The back pressure in the exhaust line is too high | Check the hose and/or the pipe | Chapter 5.3 |
| Machine is switched off by the motor protection switch p.33 ↗ | Permanent operation >100 mbar (abs.). | Use next largest motor output | Chapter 4.4 |
| Pumping capacity is insufficient p.33 ↗ | The inlet pipe is too long or too narrow | Check the hose and/or the pipe | Chapter 5.3 |
| Pumping capacity is insufficient p.33 ↗ | Leak on the inlet side of the vacuum pump or in the system | Check the pipework and screw connections for leaks and check for tight fit | Chapter 7.2 |
| Pumping capacity is insufficient p.33 ↗ | The intake filter is dirty | Clean or replace the intake filter | Chapter 7.5 |
| Final pressure (max. vacuum) is not reached p.34 ↗ | Leak on the inlet side of the vacuum pump or in the system | Check the pipework and screw connections for leaks and check for tight fit | Chapter 7.2 |
| Final pressure (max. vacuum) is not reached p.34 ↗ | Incorrect oil viscosity | The oil viscosity must comply with ISO VG 100 as per DIN ISO 3448 | Chapter 7.6 |
| Machine gets too hot p.34 ↗ | Ambient or inlet temperatures too high | Ensure proper use | Chapter 2.4 |
| Machine gets too hot p.34 ↗ | Cooling air supply is obstructed | Check ambient conditions | Chapter 5.1 |
| Machine gets too hot p.34 ↗ | Cooling air supply is obstructed | Clean ventilation slots | Chapter 7.8 |
| Machine gets too hot p.34 ↗ | Soiled oil cooler | Clean the oil cooler and fan, renew the fan if necessary | Chapter 7.8 |
| Machine gets too hot p.34 ↗ | The lubricating oil is too viscous | The oil viscosity must comply with ISO VG 100 as per DIN ISO 3448 | Chapter 7.6 |
| Machine gets too hot p.34 ↗ | The air oil separator elements are dirty. | Change the oil separator elements | Chapter 7.7 |
| Machine gets too hot p.34 ↗ | The back pressure in the exhaust line is too high | Check the hose and/or the pipe | Chapter 5.3 |
| Exhaust air contains visible oil mist p.34 ↗ | The oil separator elements are not inserted correctly or the O rings are missing. | Check that it is correctly seated | Chapter 7.7 |
| Exhaust air contains visible oil mist p.34 ↗ | Unsuitable oil is being used | Use suitable types | Chapter 7.6 |
| Exhaust air contains visible oil mist p.34 ↗ | The air oil separator elements are dirty | Change the oil separator elements | Chapter 7.7 |
| Exhaust air contains visible oil mist p.34 ↗ | Ambient or inlet temperatures too high | Ensure proper use | Chapter 2.4 |
| Exhaust air contains visible oil mist p.34 ↗ | Cooling air supply is obstructed | Check ambient conditions | Chapter 5.1 |
| Exhaust air contains visible oil mist p.34 ↗ | Cooling air supply is obstructed | Clean ventilation slots | Chapter 7.2 |
| The machine makes a strange noise (The blades making a hammering noise when starting from cold is normal if it disappears within two minutes as the operating te p.34 ↗ | The pump housing is worn (chatter marks) | Repair by manufacturer or authorised workshop | Elmo Rietschle Service |
| The machine makes a strange noise (The blades making a hammering noise when starting from cold is normal if it disappears within two minutes as the operating te p.34 ↗ | The vacuum adjustment valve (if available) is vibrating | Replace the valve | Chapter 7.11 |
| The machine makes a strange noise (The blades making a hammering noise when starting from cold is normal if it disappears within two minutes as the operating te p.34 ↗ | Blades are damaged | Repair by manufacturer or authorised workshop | Elmo Rietschle Service |
| The machine makes a strange noise (The blades making a hammering noise when starting from cold is normal if it disappears within two minutes as the operating te p.34 ↗ | Vacuum pump or its oil is too cold | Note the ambient temperature and the inlet temperature | Chapter 2.4 |
| The machine makes a strange noise (The blades making a hammering noise when starting from cold is normal if it disappears within two minutes as the operating te p.34 ↗ | The lubricating oil is too viscous | The oil viscosity must comply with ISO VG 100 as per DIN ISO 3448 | Chapter 7.6 |
| The machine makes a strange noise p.35 ↗ | Coupling defective or coupling sleeve worn out | Check and replace coupling / coupling sleeve | Chapter 7.9.2 |
| Water in lubricating oil p.35 ↗ | Pump sucks in water | Install water interceptor upstream of the pump | — |
| Water in lubricating oil p.35 ↗ | The pump sucks in more water vapour than is suitable for its water vapour compatibility | Contact the manufacturer for increased gas ballast | — |
| Water in lubricating oil p.35 ↗ | Pump only works for a short time and therefore does not reach its normal operating temperature | Let the pump continue to run with a closed suction side after extracting the water vapour until the water has evaporated from the oil | — |