Induztr
Resumen técnico Visor de documentos Modelos relacionados

ASI 35 — product leaflet

Technical Reference Summary

Covered Models & Document Scope

Detector de fugas de helio/hidrógeno Pfeiffer Vacuum ASI 35 (pruebas de pulverización y de aspiración). Accesorios/opciones enumerados: cables, módulo de aspiración, sonda de aspiración con diferentes longitudes de manguera, interfaces de comunicación. Opciones de puerto de entrada DN 25 ISO-KF o DN 16 ISO-KF.

Section-by-Section Technical Breakdown

pp. 1
Características principales

El ASI 35 se presenta como flexible, preciso y robusto. Su diseño modular tiene una huella reducida para facilitar la integración en sistemas de detección de fugas, con alta sensibilidad para tiempos de ciclo cortos y alto rendimiento de producción, además de largos intervalos de mantenimiento.

  • Flexible: modular design, small footprint, easy integration into any leak detection system
  • Accurate: high sensitivity, repeatable measurements, suitable for short cycle time and high production throughput
  • Robust: high reliability, long maintenance intervals
pp. 1
Accesorios, piezas de repuesto y opciones

Enumera los accesorios y opciones disponibles para el ASI 35. Incluye hardware de aspiración e interfaces de comunicación de estándar industrial.

  • Cable
  • Sniffer module
  • Sniffer probe with different hose length
  • Communication interface compatible with industrial standards
pp. 2
Datos técnicos

Especificaciones principales del ASI 35 que abarcan métodos de prueba, sensibilidad, compatibilidad de gases, interfaces, alimentación, dimensiones y pesos. La unidad consta de tres módulos físicos: módulo de vacío, módulo electrónico y panel de control.

  • Test methods: spraying and sniffing tests
  • Detectable gases: ⁴He; ³He; H₂
  • Min. detectable leak rate (Helium, spraying): 5·10⁻¹² mbar l/s / 5·10⁻¹³ Pa m³/s
  • Min. detectable leak rate (Helium, sniffing): 1.5·10⁻⁸ mbar l/s / 1.5·10⁻⁹ Pa m³/s
  • Helium pumping speed: 6 l/s
  • Max. test inlet pressure: 18 mbar
  • Start-up time (20 °C): <3 min
  • Operating temperature: 10–45 °C
  • Communication interfaces: I/O, RS-232, Profibus, Profinet
  • Inlet port: DN 25 ISO-KF, DN 16 ISO-KF
  • Dimensions (L×W×H): vacuum module 279×264×235 mm; electronic module 216×317×111 mm; control panel 241×54×133 mm
  • Weight approx.: vacuum module 15 kg / electronic module 5 kg / control panel 1.3 kg
  • Power supply: 90–240 V (50/60 Hz); max. power consumption 300 W

Key Integration, Operating & Safety Requirements

Specification / Condition Engineering Implication Aplica a
Caudal de fuga mínimo detectable para helio en prueba de pulverización (vacío): 5·10⁻¹² mbar l/s (5·10⁻¹³ Pa m³/s) p.2 ↗ Suitable for high-sensitivity vacuum leak testing; spec must not be confused with the much higher sniffing detection limit ASI 35
Caudal de fuga mínimo detectable para helio en prueba de aspiración: 1.5·10⁻⁸ mbar l/s (1.5·10⁻⁹ Pa m³/s) p.2 ↗ For atmospheric sniffing applications, design test criteria around this ~4 orders of magnitude worse limit than vacuum mode ASI 35 (sniffing operation)
Gases trazadores detectables: ⁴He, ³He y H₂ p.2 ↗ Hydrogen test possible where helium cost/supply is an issue; verify gas-specific sensitivities before certifying ASI 35
La velocidad de bombeo de helio es 6 l/s p.2 ↗ Determines response/recovery time of vacuum test cycles and pump-down of small test volumes ASI 35
La presión máxima de entrada de prueba es 18 mbar p.2 ↗ Test parts must be evacuated below 18 mbar before opening the leak detector inlet; use a backing/roughing pump above this pressure ASI 35
El tiempo de arranque a 20 °C es inferior a 3 minutos p.2 ↗ Enables short shift startup in production environments; allow ~3 min before first valid measurement ASI 35
El rango de temperatura de funcionamiento es 10–45 °C p.2 ↗ Installation site must be climate-controlled; outside this range accuracy/reliability are not guaranteed ASI 35
Interfaces de comunicación disponibles: I/O, RS-232, Profibus, Profinet p.2 ↗ Direct PLC integration possible in automated production lines without additional gateways for Profibus/Profinet environments ASI 35
Puertos de entrada disponibles: DN 25 ISO-KF y DN 16 ISO-KF p.2 ↗ Select KF flange hardware/adapters accordingly; DN 16 reduces conductance versus DN 25 ASI 35
La alimentación es 90–240 V, 50/60 Hz con un consumo máximo de 300 W p.2 ↗ Single-phase worldwide supply compatibility; size supply/breaker for at least 300 W per unit ASI 35
El sistema se divide en módulo de vacío (279×264×235 mm, 15 kg), módulo electrónico (216×317×111 mm, 5 kg) y panel de control (241×54×133 mm, 1.3 kg) p.2 ↗ Modular layout allows distributed installation; mounting plates and enclosures must be dimensioned per module, total mass ~21.3 kg ASI 35
La sonda de aspiración opcional está disponible con diferentes longitudes de manguera p.1 ↗ Hose length selection affects sniffing response time and the stated 1.5·10⁻⁸ mbar l/s sniffing limit; choose shortest practical length ASI 35 with sniffer module/probe option

Modelos relacionados