Induztr
Resumen técnico Visor de documentos Modelos relacionados

Installing the 2998 PDA Detector Flow Cell

Technical Reference Summary

Covered Models & Document Scope

Este documento abarca la sustitución de las celdas de flujo para el detector de matriz de fotodiodos 2998. Hay disponibles cuatro kits de celda de flujo: analítica (205000399), microbore (205000400), semipreparativa (205000401) y autopurificación (205000402). El procedimiento se aplica a todas estas variantes.

Section-by-Section Technical Breakdown

pp. 1
Especificaciones de la celda de flujo

La tabla 2 enumera las especificaciones de cada celda de flujo disponible, incluidos el volumen, la longitud del camino óptico, el diámetro interno del tubo y la presión nominal. La celda de flujo de autopurificación tiene diámetros de tubo de entrada y de salida separados y una presión nominal superior.

  • Analytical: volume 9 µL, pathlength 10 mm, tubing ID 0.010 in, pressure rating 69 bar/1000 psi.
  • Autopurification: volume 11 µL, pathlength 0.5 mm, inlet tubing ID 0.010 in, outlet tubing ID 0.040 in, pressure rating 138 bar/2000 psi.
  • Microbore: volume 3 µL, pathlength 8 mm, tubing ID 0.005 in, pressure rating 69 bar/1000 psi.
  • Semi-preparative: volume 17 µL, pathlength 3 mm, tubing ID 0.020 in, pressure rating 69 bar/1000 psi.
  • Cuvette: volume N/A, pathlength 10 mm, tubing ID N/A, pressure rating N/A.
pp. 1-3
Procedimiento de sustitución de la celda de flujo

Instrucciones paso a paso para extraer e instalar una celda de flujo en el detector 2998. El procedimiento incluye apagar el equipo, desconectar los tubos, extraer la celda de flujo antigua, insertar la nueva con la alineación correcta, apretar los tornillos de mariposa, volver a conectar los tubos y cebar el sistema.

  • Tools required: 1/4-inch flat-blade screwdriver.
  • Power off the detector and stop solvent flow before starting.
  • Lift up the detector front cover and pull it from the chassis.
  • Disconnect inlet and outlet tubing from their connections.
  • Loosen three thumbscrews on the flow cell front plate with the screwdriver.
  • Grasp the handle and gently pull the flow cell toward you.
  • Unpack and inspect the new flow cell.
  • Square the flow cell assembly in front of the opening and insert it into the optics bench, using the alignment pins.
  • Push the front of the assembly until it seats on the front alignment pins.
  • Continue inserting until the three thumbscrews align with their holes.
  • Alternate between tightening the captive screws and pushing the flow cell forward to prevent binding and ensure proper seating.
  • Hand tighten the thumbscrews, then tighten snug with the screwdriver.
  • Connect inlet tubing to the column outlet and flow cell inlet.
  • Replace the front panel cover.
  • Prime the system to fill the flow cell with solvent and remove air before powering on.

Key Integration, Operating & Safety Requirements

Specification / Condition Engineering Implication Aplica a
La celda de flujo analítica (205000399) tiene un volumen de 9 µL, una longitud del camino óptico de 10 mm, un diámetro interno del tubo de 0.010 pulgadas y una presión nominal de 69 bar/1000 psi. p.1 ↗ Select this flow cell for standard analytical separations where high sensitivity and moderate pressure are required. Analytical flow cell
La celda de flujo de autopurificación (205000402) tiene un volumen de 11 µL, una longitud del camino óptico de 0.5 mm, un diámetro interno del tubo de entrada de 0.010 pulgadas, un diámetro interno del tubo de salida de 0.040 pulgadas y una presión nominal de 138 bar/2000 psi. p.1 ↗ Use this flow cell for purification applications requiring higher pressure and larger outlet tubing to accommodate higher flow rates. Autopurification flow cell
La celda de flujo microbore (205000400) tiene un volumen de 3 µL, una longitud del camino óptico de 8 mm, un diámetro interno del tubo de 0.005 pulgadas y una presión nominal de 69 bar/1000 psi. p.1 ↗ Choose this flow cell for microbore LC applications where low volume and minimal band broadening are critical. Microbore flow cell
La celda de flujo semipreparativa (205000401) tiene un volumen de 17 µL, una longitud del camino óptico de 3 mm, un diámetro interno del tubo de 0.020 pulgadas y una presión nominal de 69 bar/1000 psi. p.1 ↗ Use this flow cell for semi-preparative scale purifications where larger tubing and shorter pathlength reduce backpressure and accommodate higher flow rates. Semi-preparative flow cell
La celda de flujo de autopurificación opcional tiene tres racores: entrada analítica, entrada preparativa y salida. p.2 ↗ When installing this flow cell, ensure all three connections are made correctly to avoid leaks or improper flow. Autopurification flow cell
La celda de flujo utiliza pasadores de alineación en el banco óptico para su correcta colocación. p.2 ↗ When inserting the flow cell, square it in front of the opening and push until it seats on the front alignment pins to ensure correct optical alignment. All flow cells
Para evitar que se agarrote y garantizar un asiento correcto, alterne entre apretar los tornillos cautivos y empujar la celda de flujo hacia delante. p.3 ↗ Follow this alternating technique during installation to avoid damaging the flow cell or optics bench. All flow cells
Apriete los tornillos de mariposa a mano y, a continuación, apriételos firmemente con un destornillador de punta plana de 1/4 de pulgada. p.10 ↗ Do not overtighten; snug tightening is sufficient to secure the flow cell without damaging the threads or seals. All flow cells
Antes de encender el detector, cebe el sistema para llenar la celda de flujo con disolvente y eliminar el aire. p.13 ↗ Priming prevents air bubbles from affecting detector performance and ensures the flow cell is ready for operation. All flow cells
Se requiere un destornillador de punta plana de 1/4 de pulgada para aflojar y apretar los tres tornillos de mariposa del conjunto de la celda de flujo. p.1 ↗ Ensure this tool is available before starting the replacement procedure. All flow cells