Agilent 2100 Bioanalyzer System Maintenance and Troubleshooting Guide
Technical Reference Summary
Covered Models & Document Scope
Mantenimiento y resolución de problemas del sistema Agilent 2100 Bioanalyzer, basado en el software 2100 Expert revisión B.02.08 y posteriores. Abarca la comunicación del instrumento, el software 2100 Expert, los diagnósticos de hardware, las aplicaciones de DNA/RNA/Protein, el cartucho de electrodos, la estación de cebado de chips, el instrumento, el vortexador y las piezas de repuesto. Las notas de aplicabilidad de las pruebas de diagnóstico indican los instrumentos G2939A, G2938B y C para la prueba de precisión de alta tensión con carga.
Section-by-Section Technical Breakdown
Proporciona indicaciones de manipulación relevantes para el usuario sobre herramientas, chips, reactivos, muestras, la estación de cebado de chips y el instrumento 2100 Bioanalyzer. Hace hincapié en la prevención de la contaminación, el pipeteo correcto, la equilibración de reactivos y la manipulación de chips dentro de los límites de tiempo.
- Always wear gloves when handling chips; use non-filter pipette tips of adequate size.
- Insert pipette tip to the bottom of the well when dispensing liquid to avoid bubbles.
- Replace syringe with each new kit; perform chip priming station seal test monthly.
- Keep reagents refrigerated at 4°C when not used for more than 1 hour; equilibrate to room temperature for 30 minutes before use.
- Protect dye and gel-dye mixes from light.
- Prepared chips must be used within 5 minutes.
- For DNA and RNA assays, vortex chips for 1 minute using only the IKA vortexer.
- Do not leave any wells empty; for DNA/RNA add 1 µL sample buffer to unused sample wells so total volume is at least 6 µL.
- Clean electrodes daily with electrode cleaner and monthly with toothbrush and distilled water.
- Clean focusing lens monthly or after liquid spill using isopropanol.
Describe cómo verificar la comunicación entre el PC y el instrumento, resolver problemas de comunicación, cambiar la configuración del puerto COM, utilizar un adaptador USB a serie y crear un paquete de soporte. Incluye un diagrama de flujo y notas sobre las claves de licencia y el comportamiento del indicador de estado.
- Status indicator lamp lights green if power is present and self-tests pass; green does not indicate PC communication.
- Verify communication by opening/closing lid and observing icon change in 2100 Expert Software.
- Ensure two licenses are registered: instrument control license and electrophoresis license.
- Check COM port settings; laptop PCs have only one COM port.
- If status indicator is red, power cycle instrument; if off and fan not running, replace fuses.
- Agilent recommends direct serial connection; if unavailable, use Agilent USB-Serial Adapter cable (Part number 5188-8031, black cable) for software B.02.08 and newer.
- Install USB-serial driver from SupportDriver/88-8031CDM21228.exe before connecting adapter.
- Create support package via Help > Create support package; ZIP file saved to desktop.
Explica cómo ejecutar la prueba de cualificación de instalación para comprobar si hay archivos de software corruptos o ausentes. Proporciona los pasos para iniciar la prueba, revisar los resultados y reinstalar el software si la prueba falla.
- Start 2100 Expert Software and select Validation (Verification) context.
- Select New Validation (Verification) > Installation Validation (Verification) > Software > [My PC Name] > Installation Qualification Test.
- Select Installation Qualification Test check box and click Start.
- If test fails, reinstall 2100 Expert Software using supplied UFD media.
- If test continues to fail, contact Agilent Technologies.
Enumera los chips de prueba disponibles y las pruebas de diagnóstico de hardware para el modo de electroforesis, y describe el procedimiento de prueba de diagnóstico. Las pruebas deben ejecutarse periódicamente o cuando se produzcan mediciones incorrectas o mensajes de error.
- Test chips: Autofocus test chip (values printed on chip, reusable) and Electrode/Diode test chip (reusable).
- Diagnostic tests include Electronic test, Fan test, Lid sensor test, Temperature test, Stepper motor test, Electrode/Diode test, High voltage stability test, High voltage accuracy test, High voltage accuracy-on load test (only for G2939A, G2938B and C instruments), Short circuit test, Optics test, Autofocus test, Laser stability test.
- Short circuit test limits specify ambient temperature of 25°C and relative humidity ≤50%.
- Diagnostic tests cannot be run while a chip run is in progress; instrument must be online.
- Results stored as .xdy files in Agilent\2100 bioanalyzer\2100 expert\diagnosis; send to Agilent Technical Support if tests fail.
Proporciona resolución de problemas basada en síntomas para los ensayos DNA y High Sensitivity DNA, enumerando las causas por probabilidad y las soluciones correspondientes. Abarca problemas como errores de cuantificación, errores de tamaño, abortos de ejecución, detección de chips, anomalías de picos, problemas de línea base y problemas de migración.
- Symptoms include Residual Gel in Spin Filter after Centrifugation, Too High/Low Quantitation Results, Wrong Sizing Result, Run Aborted, Chip Not Detected, Additional Sample or Ladder Peaks, Spikes, Low Signal Intensity, Missing Peaks, Missing Upper Marker, Broad Peaks, Baseline Dips/Noise/Jumps, Wavy Baseline, Late Migration, Peak Tailing, Unexpected Run Time, Error Message: No data received since 5 seconds.
- High Sensitivity DNA symptoms: Artefact Peaks, Split Peaks, Baseline Negative Dips.
- Causes grouped into Most probable, Probable, Least probable.
- Run Log in Log Book tab lists actions and errors during run.
- Manual marker assignment possible via right-click on peak.
Proporciona resolución de problemas basada en síntomas para los ensayos de RNA, enumerando causas y soluciones. La descripción general de la sección y los síntomas se remiten en la tabla de contenidos.
- Symptoms (RNA) section starts on page 64.
- Refer to Kit Guides for assay-specific limits.
Proporciona resolución de problemas basada en síntomas para los ensayos Protein y High Sensitivity Protein, enumerando causas y soluciones. La descripción general de la sección y los síntomas se remiten en la tabla de contenidos.
- Symptoms (Protein) section starts on page 85.
- Symptoms (High Sensitivity Protein) section starts on page 107.
Describe los procedimientos de mantenimiento del cartucho de electrodos para los ensayos DNA, protein, RNA Nano, RNA Pico y Small RNA, y cómo limpiar el conjunto de pines. Incluye instrucciones de limpieza para prevenir corrientes de fuga y contaminación.
- Clean electrodes daily using electrode cleaner.
- Thoroughly clean electrodes monthly using a toothbrush and distilled water.
- Clean electrodes with analysis-grade water and a toothbrush to address leak currents.
- Do not force chip into instrument; electrode cartridge may be damaged when lid is closed.
Abarca el mantenimiento de la estación de cebado de chips, incluido el reemplazo de la jeringa, la limpieza y el reemplazo del adaptador de jeringa, el reemplazo de la junta y la realización de una prueba de sellado para comprobar el rendimiento.
- Replace syringe with each new kit.
- Check performance monthly by applying seal test.
- Replace gasket and/or adapter if necessary.
- Refer to Kit Guide for correct position of syringe clip and base plate.
Describe la limpieza de la lente de enfoque y el cambio de fusibles. La limpieza de la lente debe realizarse mensualmente o después de cualquier derrame de líquido utilizando isopropanol.
- Clean focusing lens once a month or after any liquid spill using isopropanol.
- Replace fuses if status indicator is off and fan is not running; spare fuses come with instrument.
Abarca el cambio del adaptador del vortexador. Hay adaptadores de repuesto disponibles para los vortexadores MS-2 y MS-3.
- For MS-2 vortexers with 3 mounting screws, replacement part number is 5065-9966.
- For MS-3 vortexers with 4 mounting screws, replacement adapters may be purchased from IKA (www.ika.de) with part number 3428300.
- Press vortex adapter tightly on mount; adapter must not rock.
Proporciona una descripción general de las piezas de repuesto y accesorios para el sistema 2100 Bioanalyzer. Los números de pieza específicos se referencian a lo largo del manual.
- USB-Serial Adapter cable part number 5188-8031 (black cable) for software B.02.08 and newer.
- Vortexer adapter part numbers: 5065-9966 (MS-2, 3 screws) and 3428300 (MS-3, 4 screws, from IKA).
Key Integration, Operating & Safety Requirements
| Specification / Condition | Engineering Implication | Aplica a |
|---|---|---|
| Los chips preparados deben utilizarse en un plazo de 5 minutos. p.12 ↗ | Delays between preparation and run cause reagent evaporation and poor results. | whole series |
| Para los ensayos de DNA y RNA, vortexar los chips durante 1 minuto utilizando únicamente el vortexador IKA. p.12 ↗ | Inappropriate or insufficient vortexing leads to poor results; other vortexers are not acceptable. | DNA and RNA assays |
| Para los ensayos de DNA y RNA, añadir 1 µL de tampón de muestra a cada pocillo de muestra no utilizado para que el volumen total de líquido en cada pocillo sea de al menos 6 µL. p.12 ↗ | Empty wells cause the assay to run improperly. | DNA and RNA assays |
| Mantener los reactivos y las mezclas de reactivos refrigerados a 4°C cuando no se utilicen durante más de 1 hora. p.10 ↗ | Reagents left at room temperature may decompose, leading to poor measurement results. | whole series |
| Permitir que todos los reactivos y muestras se equilibren a temperatura ambiente durante 30 minutos; mezclar y centrifugar antes de su uso. p.10 ↗ | Cold or viscous reagents cause poor results; equilibration is required. | whole series |
| Para los ensayos de RNA, desnaturalizar por calor todas las muestras de RNA y el escalera de RNA durante 2 minutos a 70°C antes de su uso. p.11 ↗ | Required denaturation step for RNA assays. | RNA assays |
| Para los ensayos de proteínas, utilizar tubos de 0,5 mL para la desnaturalización. p.11 ↗ | Using larger tubes leads to poor results. | Protein assays |
| Limpiar los electrodos diariamente utilizando el limpiador de electrodos y mensualmente utilizando un cepillo de dientes y agua destilada. p.13 ↗ | Prevents leak currents and contamination that cause baseline and signal problems. | whole series |
| Limpiar la lente de enfoque una vez al mes (o después de cualquier derrame de líquido) utilizando isopropanol. p.13 ↗ | Fingerprints or contamination on lens cause low signal intensity and baseline noise. | whole series |
| Comprobar el rendimiento de la estación de cebado de chips aplicando la prueba de sellado mensualmente. p.9 ↗ | Ensures proper chip priming; replace gasket and/or adapter if necessary. | whole series |
| Utilizar únicamente 350 µL de agua en el chip de limpieza. p.49 ↗ | Excess water can cause leak currents due to wet cartridge. | whole series |
| Asegurar que la humedad en la sala sea inferior al 70% a 15–27°C (59–81°F). p.49 ↗ | High humidity can cause leak currents and wavy baseline. | whole series |
| Los límites de la prueba de cortocircuito especifican una temperatura ambiente de 25°C y una humedad relativa ≤50%. p.28 ↗ | Higher temperature or humidity could result in a leak current and test failure. | whole series |
| La prueba de precisión de alta tensión con carga es solo para los instrumentos G2939A, G2938B y C. p.28 ↗ | This diagnostic test is not available on other instrument variants. | G2939A, G2938B and C instruments |
| Utilizar el cable adaptador USB-Serie de Agilent (número de pieza 5188-8031, cable negro) para el software 2100 Expert versión B.02.08 y posteriores. p.20 ↗ | Required for USB connection; install driver from SupportDriver/88-8031CDM21228.exe before connecting. | 2100 Expert Software B.02.08 and newer |
| Para los vortexadores MS-2 con 3 tornillos de montaje, el número de pieza del adaptador de repuesto es 5065-9966; para los vortexadores MS-3 con 4 tornillos de montaje, utilizar el número de pieza de IKA 3428300. p.12 ↗ | Correct adapter ensures proper vortexing and prevents poor results. | MS-2 and MS-3 vortexers |
| Los resultados de las pruebas de diagnóstico se almacenan como archivos .xdy en Agilent\2100 bioanalyzer\2100 expert\diagnosis. p.30 ↗ | Send .xdy files to Agilent Technical Support if tests fail. | whole series |
| Si el indicador de estado está en rojo, apagar y volver a encender; si está apagado y el ventilador no funciona, reemplazar los fusibles. p.17 ↗ | Basic power/communication troubleshooting step. | whole series |
| Asegurar que haya dos licencias registradas: licencia de control del instrumento y licencia de electroforesis. p.17 ↗ | Missing licenses prevent instrument communication. | 2100 Expert Software |
| No tocar el instrumento 2100 Bioanalyzer durante una ejecución y nunca colocarlo sobre una superficie vibratoria ni cerca de instrumentos con circulación de aire. p.13 ↗ | Vibration and temperature changes cause baseline jumps, spikes, and sizing errors. | whole series |
Faults & Troubleshooting
| Código / Síntoma | Possible Cause | Remedy | Note |
|---|---|---|---|
| Run aborted on port x. Instrument error occurred on port x, Unusual high or low voltage or current was detected during the start phase of the on-chip analysis. p.37 ↗ | Insufficient volume in well(s); air bubble at bottom of well; dirty electrodes; chip not properly primed; chip prepared with cold reagents; high voltage power supply defective. | Check Kit Guide for liquid amounts; ensure all wells contain sufficient ladder, samples or buffer; insert pipette tip to bottom of well; remove large air bubbles; clean electrodes; prepare new chip and check priming station; allow reagents to warm to room temperature for 30 minutes; check high voltage power supply via hardware diagnostics. | Logbook error message; marked wells indicate problematic wells. |
| Chip Not Detected p.38 ↗ | No communication between instrument and PC; insufficient volume in well(s); chip not properly primed/air bubble; expired reagents; high voltage power supply defective. | Check instrument communication; check Kit Guide for liquid amounts; prepare new chip and check priming station; prepare new chip with fresh reagents; check high voltage power supply via hardware diagnostics. | Section 5, Symptoms (DNA) |
| Error Message: No data received since 5 seconds p.57 ↗ | Not detailed in provided text. | Not detailed in provided text. | Listed in Symptoms (DNA) table of contents, page 57. |
| Residual Gel in Spin Filter after Centrifugation p.34 ↗ | Gel filtered at insufficient g-value; cooled centrifuge used; gel too cool or viscous. | Refer to Kit Guide for proper centrifuge settings; repeat centrifugation at room temperature; equilibrate reagents at room temperature for 30 minutes prior to use. | Section 5, Symptoms (DNA) |
| Too High Quantitation Results p.34 ↗ | Pipetting error during reagent mix preparation; chip pipetting error; insufficient vortexing; dye concentration too low; low or missing upper marker; loaded chip kept too long before run. | Check dilution procedure and pipette calibration; prepare new chip and pipette to bottom of well; vortex chip for 1 minute with IKA vortexer; use correct dye concentration and warm dye to room temperature for 30 minutes protected from light; check Missing Upper Marker; use prepared chip within 5 minutes. | Section 5, Symptoms (DNA) |
| Too Low Quantitation Results p.35 ↗ | Pipetting error; chip pipetting error; insufficient vortexing; loaded chip kept too long; dye concentration too high; sample concentration too high. | Check dilution procedure and pipette calibration; prepare new chip and pipette to bottom of well; vortex chip for 1 minute with IKA vortexer; use prepared chip within 5 minutes; use correct dye concentration and warm dye to room temperature for 30 minutes; use sample concentration according to Kit Guide. | Section 5, Symptoms (DNA) |
| Wrong Sizing Result p.36 ↗ | DNA ladder degraded; chip not properly primed/clogged priming station/wrong settings; chip contaminated; markers called incorrectly; loaded chip kept too long; no ladder in ladder well; vibration; ambient temperature changes >5°C; high voltage power supply defective. | Check expiration date; prepare new chip and check priming station seal test; clean/replace syringe, gasket, adapter; check clip and base plate positions; wear powder-free gloves; do not touch chip underside or wells; clean electrodes; load chip immediately; manually assign lower marker; use chip within 5 minutes; prepare new chip with ladder; do not touch instrument during run; remove vibration devices; place in thermally stable environment; check high voltage power supply. | Section 5, Symptoms (DNA) |
| Additional Sample or Ladder Peaks p.39 ↗ | Chip or gel-dye mix contaminated with particles; sample degraded or contaminated; chip prepared with cold reagents; chip not properly primed; vibration; dye agglomerates; DNA ladder degraded. | Prepare new chip with new gel-dye mix; wear powder-free gloves; do not touch chip underside or wells; clean electrodes; load chip immediately; always wear gloves; allow reagents to warm to room temperature for 30 minutes; check priming station; do not touch instrument during run; remove vibration devices; use correct dye concentration and warm/protect from light; take gel-dye mix from top of tube after centrifugation; check expiration date and use fresh DNA ladder. | Section 5, Symptoms (DNA) |
| Spikes p.40 ↗ | Vibration of instrument; chip or gel-dye mix contaminated with particles; dye agglomerates; chip prepared with cold reagents. | Do not touch instrument during run; remove vibration devices; prepare new chip with new gel-dye mix; wear powder-free gloves; do not touch chip underside or wells; clean electrodes; load chip immediately; use correct dye concentration and warm/protect from light; take gel-dye mix from top of tube after centrifugation; allow reagents to warm to room temperature for 30 minutes. | Section 5, Symptoms (DNA) |
| Low Signal Intensity p.41 ↗ | Dye concentration too low; pipetting error; chip pipetting error; fingerprint on focusing lens or chip backside; insufficient vortexing; chip contaminated; vibration; autofocus failure. | Use correct dye concentration and warm/protect from light; check dilution procedure and pipette calibration; pipette new chip to bottom of well; clean lens with isopropanol; do not touch chip underside; vortex chip for 1 minute with IKA vortexer; wear powder-free gloves; do not touch wells; clean electrodes; load chip immediately; do not touch instrument during run; remove vibration devices; check autofocus via hardware diagnostics. | Section 5, Symptoms (DNA) |
| Missing Peaks p.43 ↗ | Sample salt concentration too high; chip not properly primed; leak currents due to contaminated electrodes; laser broken; autofocus failure or high voltage power supply defective. | Refer to Kit Guide for maximum salt limits; dilute samples with deionized DNase-free water; prepare new chip and check priming station; clean electrodes with analysis-grade water and toothbrush; perform Optics, Autofocus, and Laser Stability tests; check autofocus and high voltage power supply via hardware diagnostics. | Section 5, Symptoms (DNA) |
| Missing Upper Marker p.44 ↗ | Alignment of upper marker not set properly; upper marker digested by restriction enzymes; sample salt concentration too high. | Manually assign upper marker; inactivate restriction enzymes by adding EDTA or heat per manufacturer's instructions; refer to Kit Guide for maximum salt limits and dilute samples with deionized DNase-free water if necessary. | Section 5, Symptoms (DNA) |
| Broad Peaks p.45 ↗ | Leak currents due to contaminated electrodes; chip not properly primed; dye concentration too high; genomic DNA or cDNA contamination. | Clean electrodes with analysis-grade water and toothbrush; prepare new chip and check priming station; use correct dye concentration and warm to room temperature for 30 minutes; check DNA preparation procedure. | Section 5, Symptoms (DNA) |
| Baseline Dips p.46 ↗ | Sample concentration too high; sample impurities; sample salt concentration too high; dye concentration too low; autofocus failure. | Use sample concentration according to Kit Guide; check DNA isolation protocol and clean up samples; refer to Kit Guide for maximum salt limits and dilute with deionized DNase-free water; use correct dye concentration and warm/protect from light; check autofocus via hardware diagnostics. | Section 5, Symptoms (DNA) |
| Baseline Noise p.47 ↗ | Chip contaminated; fingerprint on focusing lens or chip backside; autofocus failure or high voltage power supply defective. | Wear powder-free gloves; do not touch chip underside or wells; clean electrodes; load chip immediately; clean lens with isopropanol; check autofocus and high voltage power supply via hardware diagnostics. | Section 5, Symptoms (DNA) |
| Baseline Jumps p.48 ↗ | Vibration of instrument; instrument lid touched during run; laser defective. | Remove vibration devices from bench; do not touch instrument during run; check laser via hardware diagnostics. | Section 5, Symptoms (DNA) |
| Wavy Baseline p.49 ↗ | Leak currents due to contaminated electrodes; leak currents due to liquid spillage on top of chip; dye concentration too low; chip not properly primed; leak currents due to wet cartridge; ambient temperature changes >5°C; high voltage power supply defective. | Clean electrodes; prepare new chip and lower vortexing speed or mix manually; use correct dye concentration and warm to room temperature for 30 minutes; check priming station; use only 350 µL water in cleaning chip; ensure humidity below 70% at 15–27°C; place in thermally stable environment; check high voltage power supply. | Section 5, Symptoms (DNA) |
| Late Migration p.50 ↗ | Chip not properly primed; leak currents due to contaminated electrodes; leak currents due to liquid spillage; loss of gel separation properties; dye concentration too high; vortex speed too high; genomic DNA or high molecular weight DNA contamination; vortex adapter not connected tightly; ambient temperature changes >5°C. | Prepare new chip and check priming station; clean electrodes; prepare new chip and lower vortexing speed or mix manually; check Kit Guide for proper storage and use gel-dye mix within indicated time; use correct dye concentration; vortex chip for 1 minute with IKA vortexer at setpoint; check DNA isolation protocol; press vortex adapter tightly on mount; replace adapter if needed; place in thermally stable environment. | Section 5, Symptoms (DNA) |
| Peak Tailing p.52 ↗ | Sample salt concentration too high. | Refer to Kit Guide for maximum salt limits; dilute samples with deionized DNase-free water if necessary. | Section 5, Symptoms (DNA) |
| Unexpected Run Time p.53 ↗ | Lower and/or upper markers are called incorrectly. | Turn off alignment and check which bands are correct lower and upper markers; manually assign markers. | Section 5, Symptoms (DNA) |