Agilent 6200 Series TOF and 6500 Series Q-TOF LC/MS Quick Start Guide
Technical Reference Summary
Covered Models & Document Scope
Abarca sistemas Agilent 6200 Series TOF LC/MS (6224, 6230) y 6500 Series Q-TOF LC/MS (6520B, 6530A/B, 6538A, 6540A/B, 6545, 6545XT, 6546, 6550, 6560 Ion Mobility) con MassHunter Workstation Software versiones B.09.00 y 10.0; módulos LC compatibles 1200, 1260, 1260 Infinity II, 1290 Infinity, 1290 Infinity II y fuentes de ionización ESI, Dual ESI, AJS ESI, Dual AJS ESI, APCI, APPI, Multimode, nanospray, dual nanospray, MALDI, GC-APCI.
Section-by-Section Technical Breakdown
Enumera qué fuentes de ionización son compatibles para todos los procedimientos de ajuste automatizado en cada modelo TOF y Q-TOF. Las fuentes NanoESI, Dual nanoESI, MALDI y GC-QTOF no pueden utilizarse para ningún ajuste automatizado. La fuente Dual ESI es compatible con todos los Autotunes en todos los instrumentos.
- 6224 TOF: ESI, Dual ESI
- 6230 TOF: ESI, Dual ESI, AJS ESI, Dual AJS ESI
- 6520B Q-TOF: ESI, Dual ESI
- 6530A/B Q-TOF: ESI, Dual ESI, AJS ESI, Dual AJS ESI
- 6538 Q-TOF: ESI, Dual ESI
- 6540A/B Q-TOF: ESI, Dual ESI, AJS ESI, Dual AJS ESI
- 6545, 6545XT, 6546 Q-TOF: ESI, Dual ESI, AJS ESI, Dual AJS ESI
- 6550: ESI, Dual ESI, AJS ESI, Dual AJS ESI
- 6560: Dual ESI, Dual AJS ESI
- 6545XT ships with dielectric capillary; resistive capillary required for Fast Polarity Switching
Describe el algoritmo de autotune SWARM utilizado en los instrumentos 6224/6230 TOF y 6530, 6545, 6545XT, 6546, 6550, 6560 Q-TOF. Combina Particle Swarm Optimization y un algoritmo simplex, intercambiándolos entre ajuste grueso y fino, con parámetros acotados por la física de iones. System Tune es el SWARM Initial Auto Tune que incluye el ajuste del detector y requiere el rango de masas Standard (3200 m/z).
- System Tune requires Standard (3200 m/z) Mass Range
- Transmission Tune does not include detector tune; run as frequently as needed
- Low (1700 m/z) Mass Range disables System Tune
- High Resolution Slicer Mode must be selected before System Tune
- Set Detector Gain and System Tune only with mass range 3200 m/z
- Fragile Ions checkbox reduces Fragmentor Voltage to minimize fragmentation
Cubre el flujo de trabajo de autotune clásico para instrumentos TOF y Q-TOF distintos de los modelos SWARM. Initial Tune, Standard Tune y Set Detector Gain requieren el modo de instrumento Extended Dynamic Range y el rango de masas Standard (3200 m/z). Tras cambiar el rango de masas o el modo de instrumento, se requiere recalibración.
- Instrument Mode must be Extended Dynamic Range for Set Detector Gain, Standard Tune, Initial Tune
- Mass Range must be Standard (3200 m/z) for Set Detector Gain and Initial Auto Tune
- High Resolution Slicer Mode required before Initial Auto Tune
- For 6530 with Dual AJS ESI, 6538 or 6540, do not click Both; tune TOF then Quadrupole with tuning mix change
- Software B.05.01 SP1 or later: additional Quad Tune in 1700 m/z range after Initial Tune improves molecules < 300 m/z
Especifica las relaciones de dilución del tune mix por modelo de instrumento, fuente y polaridad. El autotune puede fallar en 6530A, 6540A, 6545A, 6545XT, 6546, 6550A y 6560A con AJS ESI o Dual AJS ESI a menos que se diluya el tuning mix. La polaridad de iones negativos generalmente requiere dilución para una calibración adecuada.
- 6545, 6545XT, 6550A, 6560A with Dual AJS ESI: 1:10 dilution both polarities
- 6530 with Dual AJS ESI: 1:10 positive, 1:40 negative
- 6538A: undiluted tune mix
- 6230 TOF with AJS/Dual AJS ESI: 1:10 positive, 1:40 negative
- 6224 TOF with Dual ESI: do not dilute for positive ion
- 6550 Q-TOF always uses 1:10 dilution
Explica la calibración del eje de masas: se infunde una muestra con masas conocidas y se miden los tiempos de vuelo para calcular los coeficientes de calibración actualizados. Se requiere recalibración y verificación del ajuste tras cambiar Instrument Mode, Mass Range o Slicer Mode. Mass Calibration se activa mediante Mass Calibration/Check, Quick Tune, Standard Tune o Initial Auto Tune (Classic) o mediante Mass Calibration/Check, Transmission Tune o System Tune (SWARM).
- Recalibrate after changing Instrument Mode, Mass Range or Slicer Mode
- 6545 with 50-250 m/z option uses calibrant ions below 100 m/z
- Repeat Mass Calibration/Check if calibrant abundances exceed 480,000 (6538/6540) or ~650,000 (other TOF/Q-TOF)
- Agilent recommends regular mass-axis calibration
Describe la preparación del LC antes de la adquisición por MS: desviar el flujo del LC a residuos mientras se acondiciona/equilibra la columna, purgar la bomba del LC, acondicionar la columna, configurar la monitorización de valores reales en tiempo real con límites mín./máx. y configurar las visualizaciones de gráficos en tiempo real.
- Switch LC Stream to Waste in Method Editor General tab before conditioning column
- Apply Now sends only the current LC eluent value; Apply sends all method parameters
- Purge the LC pump per the pump User Guide
- Actuals window: set min/max values; out-of-range values shown with red background
- Monitor baseline to confirm column equilibration
Cubre el ajuste del instrumento TOF o Q-TOF: cuándo se requiere el ajuste, selección de autotune SWARM vs Classic, fuentes compatibles, dilución del tune mix, calibración del eje de masas y conmutación del flujo del LC de Waste a MS tras el ajuste. También cubre la monitorización de la línea base del MS y el uso del System Logbook Viewer.
- Tune first use or after maintenance, service or pump-down and restart
- Switch LC stream to MS after conditioning column and tuning
- Monitor TOF/Q-TOF baseline stability and absence of interfering spectra
- System Logbook Viewer: click Log on Data Acquisition toolbar or enable task bar notification
- Manual tune recommended only for ion source and optics 1; not after collision cell
Describe las siete ventanas de Data Acquisition: Instrument Status, Actuals, Chromatogram Plot, Spectrum Pane, Method Editor, Sample Run y Worklist. Instrument Status muestra el estado de los dispositivos mediante texto y codificación por colores; Method Editor contiene los parámetros de adquisición y, para el 6560, la sección Acquisition Mode.
- Instrument Status window shows each device status as text and color-coded
- Actuals window shows current values of selected parameters with conditional formatting
- Spectrum Pane shows spectra from different devices on different tabs
- Sample Run window supports Override DA Method and Method Type Both Acquisition and DA or DA Only
- Worklist window runs samples in listed order; Part of method to run options Acquisition Only, Both Acquisition and DA, DA only
La ventana Tune se utiliza para ajustar el espectrómetro de masas con algoritmos automatizados o manualmente, seleccionar el modo de instrumento y calibrar. Para el 6560 Ion Mobility Q-TOF contiene la sección Acquisition Mode (IM-QTOF o QTOF-Only). Existen opciones adicionales de autotune para moléculas pequeñas en 6545, 6545XT, 6550 y 6560; el 6545XT también admite autotune para moléculas grandes.
- Manual tuning recommended only for ion source and optics 1
- 6560: select IM-QTOF or QTOF-Only in Acquisition Mode
- 6545, 6545XT, 6550, 6560: additional small molecule autotune options
- 6545XT: large molecule autotune available
- Cannot do small molecule tune after large molecule autotune; upload older system tune file or do system tune first
Key Integration, Operating & Safety Requirements
| Specification / Condition | Engineering Implication | Aplica a |
|---|---|---|
| System Tune (SWARM Initial Auto Tune) solo puede realizarse con Mass Range ajustado a Standard (3200 m/z). p.25 ↗ | Select Standard mass range before System Tune; Low (1700 m/z) disables System Tune. | 6224/6230 TOF and 6530, 6545, 6545XT, 6546, 6550, 6560 Q-TOF |
| High Resolution Slicer Mode debe seleccionarse antes de realizar un System Tune o Initial Auto Tune. p.22 ↗ | Set Slicer Mode to High Resolution before these tunes to obtain best tuning results. | Instruments with Slicer Mode option |
| Set Detector Gain y System Tune (TOF o Quadrupole) requieren un rango de masas de 3200 m/z. p.22 ↗ | These buttons are grayed out or missing with other mass ranges or unsupported sources. | SWARM and Classic autotune instruments |
| Classic Initial Tune, Standard Tune y Set Detector Gain requieren Instrument Mode Extended Dynamic Range. p.22 ↗ | Select Extended Dynamic Range before running these autotunes; buttons gray out otherwise. | Classic autotune TOF/Q-TOF instruments |
| Tras cambiar Instrument Mode, Mass Range o Slicer Mode, el TOF o Q-TOF debe recalibrarse. p.22 ↗ | Plan a Mass Calibration/Check after any such change before acquiring data. | All TOF and Q-TOF models |
| Repita Mass Calibration/Check si las abundancias de los iones calibradores superan 480.000 para 6538/6540 Q-TOF o aproximadamente 650.000 para otros instrumentos TOF/Q-TOF. p.33 ↗ | Dilute the calibration solution and repeat the check when abundances exceed these limits. | 6538/6540 Q-TOF and other TOF/Q-TOF |
| El 6550 Q-TOF utiliza siempre solución de calibración diluida 1:10. p.33 ↗ | Do not repeat Quick Tune for dilution on the 6550; dilution is always applied. | 6550 Q-TOF |
| Para aplicaciones de moléculas pequeñas en 6550 Q-TOF, ajuste Quad AMU a 100 en polaridad positiva y 90 en polaridad negativa antes del autotune. p.31 ↗ | Click Apply after each polarity change to save the Quad AMU value. | 6550 Q-TOF |
| Para 6530 con Dual AJS ESI, 6538 o 6540 en autotune clásico, no haga clic en Both; ajuste primero TOF y luego Quadrupole con un cambio de tuning mix. p.32 ↗ | Tuning mix must be changed between TOF and Quadrupole tunes on these models. | 6530 with Dual AJS ESI, 6538, 6540 |
| Fast Polarity Switching Enabled restringe el autotune a Mass Calibration/Check o FPS System Tune (SWARM) o Mass Calibration/Check o FPS Initial Auto Tune (Classic). p.23 ↗ | Polarity and Quadrupole/TOF/Both selections are unavailable when FPS is enabled. | 6224/6230 TOF and 6530, 6545, 6545XT, 6546, 6550, 6560 Q-TOF |
| El 6545XT se suministra con un capilar dieléctrico; para utilizar Fast Polarity Switching debe solicitarse a Agilent un capilar resistivo. p.23 ↗ | Order the resistive capillary if FPS is required on a 6545XT. | 6545XT Q-TOF |
| Las fuentes NanoESI, Dual nanoESI, MALDI y GC-QTOF no pueden utilizarse para ningún ajuste automatizado. p.23 ↗ | Only Mass Calibration/Check and Quick Tune (if available) are possible with these sources. | 6200 Series TOF and 6500 Series Q-TOF |
| La fuente Dual ESI es compatible con todos los Autotunes en todos los instrumentos. p.34 ↗ | Use Dual ESI when a source must support every autotune procedure. | All TOF and Q-TOF models |
| Transmission Tune tarda aproximadamente de seis a diez minutos y no incluye el ajuste del detector. p.28 ↗ | Run Transmission Tune regularly, e.g. when a different sample class is analyzed. | SWARM autotune instruments |
| Check tune tarda aproximadamente 30 segundos. p.27 ↗ | A quick check can be used to decide whether further tuning is needed. | SWARM autotune instruments |
| Quick Tune tarda de 7 a 10 minutos y no puede ejecutarse si se selecciona Quadrupole o Both como parte a ajustar. p.33 ↗ | Select TOF only when running Quick Tune. | Classic autotune instruments |
| Standard Tune tarda de 10 a 15 minutos para la parte TOF y de 10 a 15 minutos para la parte Quadrupole. p.34 ↗ | Allow sufficient time when running a Standard Tune on both parts. | Classic autotune instruments |
| Si la casilla Fragile Ions está marcada, Fragmentor Voltage se reduce para minimizar la fragmentación. p.28 ↗ | Expect lower calibrant ion signal but increased transmission of fragile ions such as metabolites and glycans. | SWARM autotune instruments |
| Para 6545XT con High (10K - 30K m/z) Mass Range, se realiza un transmission tune para moléculas grandes durante un transmission tune. p.21 ↗ | Select the specific mass range with the slider in the Instrument State tab. | 6545XT Q-TOF |
| El ajuste manual se recomienda solo para la parte frontal del instrumento: fuente de ionización y optics 1. p.15 ↗ | Do not manually tune parameters after the collision cell; manual tuning may give less than optimal results. | All TOF and Q-TOF models |
| MassHunter 10.0 solo admite el Agilent 6546; no se admiten otros espectrómetros de masas TOF o Q-TOF en esa versión. p.5 ↗ | Use MassHunter B.09.00 for other TOF/Q-TOF models. | MassHunter Workstation 10.0 |
Faults & Troubleshooting
| Código / Síntoma | Possible Cause | Remedy | Note |
|---|---|---|---|
| Autotune can fail p.24 ↗ | Tuning mix not diluted on 6530A, 6540A, 6545A, 6545XT, 6546, 6550A or 6560A with Agilent Jet Stream ESI or Dual AJS ESI source | Dilute the tuning mix as specified (e.g. 1:10 for 6545/6545XT/6550A/6560A with Dual AJS ESI) | Diluting the ESI-L Tune Mix |
| Calibration not proper in negative ion polarity p.24 ↗ | Tuning mix not diluted | Dilute the tuning mix to calibrate properly | Diluting the ESI-L Tune Mix |
| Not getting proper calibration in positive ion polarity p.24 ↗ | Tuning mix not diluted | Dilute the tuning mix | Diluting the ESI-L Tune Mix |
| Problems occur if you dilute the tune mix and tune for positive ion p.24 ↗ | Tune mix diluted on 6224 TOF with Dual ESI source | Do not dilute the tune mix for the Dual ESI source on the 6224 TOF | Diluting the ESI-L Tune Mix |
| Calibration masses detected out of the 50 to 650K range p.30 ↗ | Calibrant ion abundance too high; fragmentor voltage cannot be adjusted low enough | System tells you to dilute the calibrant and then try the calibration or autotune again | Adjust abundances for optimal calibration (6530A/B) |
| Check tune results are not acceptable p.27 ↗ | Mass calibration/optimization not within acceptance | Continue with Transmission Tune; if still unacceptable, run System Tune; if System Tune results are not acceptable, contact your local field service engineer | SWARM autotune steps 15-18 |
| Transmission tune results are not acceptable p.28 ↗ | Tune not within acceptance | Click System Tune (select Standard (3200 m/z) Mass Range and Apply if option not available); if System Tune results are not acceptable, contact your local field service engineer | SWARM autotune step 17 |
| Quick Tune results are not acceptable p.33 ↗ | Limited parameter set tune not within acceptance | Continue with Standard Tune | Classic autotune step 19-20 |
| Standard Tune produces unacceptable results p.34 ↗ | Standard Tune not within acceptance | Run an Initial Auto Tune; after performing an Initial Auto Tune, adjust the Collision Cell Gas Pressure; if this also fails, contact Agilent Field Support | Classic autotune step 20 |
| FPS Initial Auto Tune results not acceptable p.33 ↗ | Fast Polarity Switching tune not within acceptance | Contact Agilent Field Support | Classic autotune step 18 |
| Cannot do a small molecule tune after a large molecule autotune p.15 ↗ | Large molecule autotune performed on 6545XT | Upload an older system tune file first, or do a system tune | Tune window NOTE |
| Error you want to troubleshoot during instrument preparation p.36 ↗ | Instrument or software event/error | View the System Logbook Viewer: click Log on the Data Acquisition toolbar, or right-click the system task bar, click Enable Notification, then right-click LOG and click Configure | View the system logbook for events and errors |
Technical Data
| Parameter | Value | Condición |
|---|---|---|
| Mass Range (Standard) | 3200 m/z p.22 ↗ | System Tune / Initial Tune / Set Detector Gain |
| Mass Range (Low) | 1700 m/z p.21 ↗ | 6530, 6545, 6545XT, 6546, 6550, 6560 Q-TOF small molecule autotune |
| Mass Range (High) | 10K - 30K m/z p.21 ↗ | 6545XT large molecule transmission tune |
| Mass Range (High) | 10000 m/z p.27 ↗ | 6546 |
| Low mass autotune range | 50 - 1700 m/z p.27 ↗ | Low (1700 m/z) Mass Range, Quadrupole or Both |
| Calibrant abundance limit | 480,000 counts p.33 ↗ | 6538/6540 Q-TOF; repeat Mass Calibration/Check above this |
| Calibrant abundance limit | approximately 650,000 counts p.33 ↗ | other Q-TOF and TOF instruments |
| Calibrant abundance range | 50 to 650K counts p.30 ↗ | 6530A/B Adjust abundances for optimal calibration |
| Check tune duration | approximately 30 seconds p.27 ↗ | SWARM Check tune |
| Transmission Tune duration | approximately six to ten minutes p.28 ↗ | SWARM Transmission Tune |
| Mass Calibration / Check duration (TOF) | a few minutes p.33 ↗ | Classic autotune |
| Mass Calibration / Check duration (Quadrupole) | 2 to 5 minutes p.33 ↗ | Classic autotune |
| Quick Tune duration | 7 to 10 minutes p.33 ↗ | Classic autotune |
| Standard Tune duration (TOF part) | 10 to 15 minutes p.34 ↗ | Classic autotune |
| Standard Tune duration (Quadrupole part) | 10 to 15 minutes p.34 ↗ | Classic autotune |
| Quad AMU (Positive polarity) | 100 p.31 ↗ | 6550 Q-TOF small molecule applications |
| Quad AMU (Negative polarity) | 90 p.31 ↗ | 6550 Q-TOF small molecule applications |
| Tune mix dilution (positive ion TOF tune) | 1:10 diluted tune mix p.24 ↗ | 6530A with Dual AJS ESI or 6540 |
| Tune mix dilution (negative ion TOF tune) | 1:40 diluted tune mix p.24 ↗ | 6530A with Dual AJS ESI or 6540 |
| Tune mix dilution (positive ion TOF tune) | Undiluted tune mix p.24 ↗ | 6520B or 6530 with Dual ESI |
| Tune mix dilution (negative ion TOF tune) | Undiluted tune mix p.24 ↗ | 6520B or 6530 with Dual ESI |
| Tune mix dilution (polarity switching tunes) | Undiluted tune mix p.24 ↗ | 6530A with Dual AJS ESI or 6540; 6520B or 6530 with Dual ESI |
| Tune mix dilution (Quad tunes) | Undiluted tune mix p.24 ↗ | 6530A with Dual AJS ESI or 6540; 6520B or 6530 with Dual ESI |
| Tune mix dilution (SWARM, both polarities) | 1:10 diluted tune mix p.24 ↗ | 6545, 6545XT, 6550A, 6560A with Dual AJS ESI |
| Tune mix dilution (positive mode) | 1:10 diluted tune mix p.24 ↗ | 6530 with Dual AJS ESI |
| Tune mix dilution (negative mode) | 1:40 diluted tune mix p.24 ↗ | 6530 with Dual AJS ESI |
| Tune mix dilution | undiluted tune mix p.24 ↗ | 6538A |
| Tune mix dilution (positive ion) | 1:10 dilution p.24 ↗ | 6230 TOF with AJS ESI or Dual AJS ESI |
| Tune mix dilution (negative ion) | 1:40 dilution p.24 ↗ | 6230 TOF with AJS ESI or Dual AJS ESI |
| Tune mix dilution | do not dilute p.24 ↗ | 6224 TOF with Dual ESI, positive ion |
| Tune mix dilution | 1:10 dilution p.33 ↗ | 6550 Q-TOF (always) |
| LC driver version | A.02.19 SR2 p.5 ↗ | MassHunter 10.0 |
| LC driver version | A.02.19 p.5 ↗ | MassHunter B.09.00 |
| Supported operating systems | Windows 7 and Windows 10 p.5 ↗ | MassHunter B.09.00 |