Induztr
Resumen técnico Visor de documentos Modelos relacionados

Agilent 6400 Series Triple Quadrupole LC/MS System Quick Start Guide

Technical Reference Summary

Covered Models & Document Scope

Cubre los sistemas LC/MS de triple cuadrupolo Agilent 6400 Series: 6410B, 6420A, 6430A, 6460A, 6460C, 6470A, 6490A, 6495A y 6495B. La revisión B.08.02 del software Data Acquisition es compatible con 6495B; B.08.01 es compatible con 6410B, 6420A, 6430A, 6460A, 6460C, 6470A, 6490A y 6495A. Módulos LC compatibles: Agilent 1100, 1200, 1260 o 1290 Infinity, y 1260 Infinity II. El software MassHunter Workstation incluye Data Acquisition, Qualitative Analysis y Quantitative Analysis.

Section-by-Section Technical Breakdown

pp. 8-13
Paso 1. Iniciar el software Data Acquisition

Describe el inicio del programa MassHunter Data Acquisition y las ocho ventanas principales utilizadas para configurar métodos, ejecutar muestras, monitorear el estado y ajustar el instrumento. Explica el comportamiento de mostrar/ocultar ventanas, la codificación por colores del estado y las funciones de las ventanas Instrument Status, Actuals, Chromatogram Plot, Spectrum Plot, Method Editor, Sample Run, Worklist y Tune.

  • Start Data Acquisition by double-clicking the desktop icon; on Windows 7 use Start > Agilent > MassHunter Workstation > Data Acquisition; on Windows 10 use the Windows icon > Agilent > Data Acquisition.
  • If software engines need restarting, right-click the Acq System Launcher icon in the system tray and click Start Engines.
  • Instrument Status window shows device states: Error, Not ready, Pre-run, Post-run, Running, Injecting, Idle, Offline, or Standby.
  • Up to seven windows can be shown at once; windows can be floated by double-clicking the title bar and docked by double-clicking again.
  • Press F1 on the active window to obtain help.
pp. 14-17
Paso 2. Preparar los módulos LC

Cubre el cambio del flujo LC a desecho, el purgado de la bomba LC, el acondicionamiento o equilibrado de la columna, la configuración del monitoreo de actuals en tiempo real y la configuración de las visualizaciones de gráficos en tiempo real. La columna se puede acondicionar mientras se ajusta el MS de triple cuadrupolo.

  • Switch LC stream to Waste by right-clicking the QQQ device in the Instrument Status window and clicking LC > Waste.
  • Purge the LC pump according to the pump User Guide.
  • Type LC parameters and click Apply in the toolbar to download them to the LC.
  • Set up Actuals monitoring via right-click > Setup; parameters outside entered limits are shown with a red background.
  • Set up real-time plot displays by right-clicking the chromatogram plot and clicking Change.
pp. 18-20
Paso 3. Preparar el instrumento de triple cuadrupolo

Describe los procedimientos Checktune, Autotune y Manual Tune, incluidos los tiempos de ejecución esperados, las fuentes de ionización compatibles por modelo y las acciones correctivas si Checktune falla. También cubre Fast Scan Autotune y el cambio de vuelta al contexto Acquisition.

  • Checktune takes approximately 3 minutes per polarity and evaluates whether MS parameters meet specified mass accuracy and resolution.
  • Checktune can be run with ESI, AJS ESI and MMI sources.
  • Autotune takes approximately 30 minutes per ionization mode for all models except 6490 and 6495, which take approximately 25 minutes per ionization mode.
  • For all instruments except 6490 and 6495, Autotune can be run with AJS ESI and MMI sources; 6490 and 6495 Autotune only with AJS ESI.
  • If Autotune fails, mark Start from Factory Defaults and rerun Autotune.
  • Fast Scan Autotune is only supported on the 6490; Fast Scan acquisition is not supported on 6470 and 6495.
pp. 22-30
Paso 4. Configurar y ejecutar un método de adquisición

Explica la creación y el guardado de un método de adquisición, la introducción de parámetros LC y QQQ, la configuración de segmentos de barrido, el establecimiento de curvas de instrumento almacenadas, la vinculación de métodos de análisis de datos y la ejecución de muestras interactivas o listas de trabajo en modo bloqueado o desbloqueado.

  • Enter QQQ parameter values in the Time segments table; changing Scan Type clears the Scan segments table.
  • For 6490 and 6495, fragmentor voltage cannot be set in Acquisition; the tune file value is always used.
  • Add scan segments by right-clicking in the Scan segments section and clicking Add Row.
  • Stored instrument curves set in the Instrument tab are displayed in the MS Actuals window of Qualitative Analysis.
  • To run a Data Analysis method from the Sample Run window, select Both Acquisition and DA or DA Only and set Override DA method.
  • Locked mode prevents changes to method or sample parameters during a run and prevents overwriting the data file in Data Acquisition.
pp. 31
Paso 5 y Paso 6. Revisar y analizar resultados

Presenta los programas Qualitative Analysis Navigator y Workflows para revisar los resultados del desarrollo del método de adquisición, seleccionar iones precursores y productos, encontrar e identificar compuestos y realizar extracción de características moleculares. También presenta el programa Quantitative Analysis para cuantificación por lotes, revisión Batch-at-a-Glance y recuantificación utilizando valores atípicos.

  • Qualitative Analysis tasks include reviewing results for acquisition method development, selecting precursor and product ions for MRM, finding compounds, identifying compounds, and molecular feature extraction.
  • Quantitative Analysis tasks include setting up a batch and method to automatically quantitate samples, reviewing Batch-at-a-Glance results, and identifying outliers to change the method and requantitate.
  • Refer to the Qualitative Analysis and Quantitative Analysis Familiarization Guides and online Help for detailed operations.

Key Integration, Operating & Safety Requirements

Specification / Condition Engineering Implication Aplica a
Checktune tarda aproximadamente 3 minutos en ejecutarse para cada polaridad. p.3 ↗ Plan regular Checktune runs into instrument preparation time; a full two-polarity check requires about 6 minutes. 6400 Series Triple Quadrupole LC/MS
Autotune tarda aproximadamente 30 minutos para cada modo de ionización para todos los modelos excepto 6490 y 6495; los 6490 y 6495 tardan aproximadamente 25 minutos por modo de ionización. p.3 ↗ Schedule Autotune only when necessary and allow sufficient time; 6490/6495 models are faster per ionization mode. All models except 6490 and 6495; 6490 and 6495
Checktune se puede ejecutar con fuentes ESI, AJS ESI y MMI. p.3 ↗ Checktune is compatible with all three source types, allowing routine verification regardless of installed source. 6400 Series Triple Quadrupole LC/MS
Para todos los instrumentos excepto 6490 y 6495, Autotune se puede ejecutar con fuentes AJS ESI y MMI; con 6490 y 6495, Autotune solo se puede ejecutar con la fuente AJS ESI. p.3 ↗ 6490/6495 users must use the AJS ESI source for Autotune; MMI-based Autotune is not available on those models. All models except 6490/6495; 6490 and 6495
Si Autotune falla, marcar Start from Factory Defaults y hacer clic en Autotune ajusta el instrumento comenzando desde los valores predeterminados de fábrica, tardando aproximadamente 30 minutos por polaridad para todos los modelos excepto 6490 y 6495, y aproximadamente 25 minutos por modo de ionización para 6490 y 6495. p.3 ↗ Factory-default Autotune is a recovery path after failed Autotune; budget the same or slightly longer time. 6400 Series Triple Quadrupole LC/MS
Fast Scan Autotune solo ajusta con resolución Wide (1.2), Samples establecido en 1 en la pestaña Manual Tune > Acquisition, y tamaño de paso 0.2. p.3 ↗ Fast Scan acquisition requires these specific tune settings; scan time is generated automatically from step size and mass range. 6490 Triple Quadrupole
La adquisición Fast Scan no es compatible con 6470 y 6495; en su lugar, se logra una velocidad de barrido más rápida aumentando el tamaño de paso a 0.3 m/z. p.3 ↗ 6470 and 6495 users should use step size 0.3 m/z for faster scanning rather than Fast Scan mode. 6470 and 6495
Para los instrumentos 6490 y 6495, el voltaje del fragmentor no se puede establecer en Acquisition; siempre utiliza el valor del archivo de ajuste. p.4 ↗ Method development on 6490/6495 must control fragmentor via the tune file, not the acquisition method. 6490 and 6495
Se pueden monitorear hasta 4000 transiciones MRM utilizando Dynamic MRM. p.1 ↗ Dynamic MRM enables large transition panels within a single acquisition method. 6400 Series Triple Quadrupole LC/MS
El 6495B Triple Quadrupole está equipado con una válvula de compuerta para reemplazar los capilares hexabore durante el mantenimiento rutinario sin romper el vacío. p.2 ↗ Hexabore capillary replacement on 6495B does not require venting the system, reducing maintenance downtime. 6495B
Los instrumentos 6495, 6490, 6470 y 6460 Triple Quadrupole LC/MS se envían por defecto con la fuente Agilent Jet Stream utilizando gas envolvente sobrecalentado para colimar el rocío del nebulizador. p.2 ↗ These models default to AJS ESI source; method and tune development should account for AJS ESI as the standard source. 6495, 6490, 6470, 6460
Los 6490 y 6495 incluyen tecnología iFunnel que comprende el Dual Offset Ion Funnel, la fuente Agilent Jet Stream y un conjunto de desolvatación más corto con capilar Hexabore. p.1 ↗ These models provide more efficient ion sampling; maintenance procedures differ due to the hexabore capillary and shorter desolvation assembly. 6490 and 6495
El período de retención del System Logbook se puede establecer de 1 semana a 1 año a través de Tools > Purge Settings. p.3 ↗ Configure logbook purge settings to retain troubleshooting history for the desired audit or diagnostic period. 6400 Series Triple Quadrupole LC/MS with MassHunter Data Acquisition
Cuando se establecen límites de monitoreo de Actuals, un valor de parámetro fuera de los límites introducidos se muestra con fondo rojo. p.2 ↗ Use Actuals range limits as a visual alarm for out-of-spec instrument parameters during runs. 6400 Series Triple Quadrupole LC/MS
En modo bloqueado, nadie puede cambiar el método o los parámetros de muestra durante una ejecución, y el archivo de datos no se puede sobrescribir en el programa Data Acquisition. p.4 ↗ Use locked mode for regulated or unattended runs to protect method integrity and data files. 6400 Series Triple Quadrupole LC/MS
La revisión B.08.02 de Data Acquisition es compatible con 6495B, 6410B, 6420A, 6430A, 6460A, 6460C, 6470A, 6490A y 6495A, el sistema LC 1260 Infinity II, Qualitative Analysis B.08.00, Quantitative Analysis B.08.00 y ECM 3.4.1 SP2 HF3 - HF4. p.2 ↗ Verify software and firmware compatibility before upgrading; B.08.02 is required for 6495B support. 6400 Series Triple Quadrupole LC/MS
Se admiten Microsoft Windows 10 y Microsoft Windows 7. p.3 ↗ Workstation PCs must run one of these operating systems for supported operation. 6400 Series Triple Quadrupole LC/MS with MassHunter Data Acquisition B.08.02

Faults & Troubleshooting

Código / Síntoma Possible Cause Remedy Note
Checktune fails p.19 ↗ MS parameters outside limits for specified mass accuracy and resolution; failure may occur in MS1 or MS2. Use Manual Tune tab: for MS1 failure, select Peak Width (Unit, Wide, or Widest) based on failed resolution and click Adjust Gain & Offset; for MS2 failure, do the same on the MS2 tab. If Adjust Gain and Offset passes, save the autotune file via Manual Tune > Files > Save, then click Autotune tab and Checktune. If Checktune fails again, run Autotune. Step 3, page 19
Autotune fails p.20 ↗ Autotune could not achieve acceptable tune parameters. Mark the Start from Factory Defaults check box and click Autotune to tune starting from factory defaults. Check the progress box in the lower right side of the Autotune tab for reasons why the tune failed; fix the problem or call the Agilent service engineer and provide this information. Step 3, page 20
Error (Instrument Status window device state) p.21 ↗ Device error reported by the configured instrument device. View logged events and errors in the System Logbook Viewer via the Log icon in the Data Acquisition toolbar, Tools > System Logbook Viewer, or the system taskbar LOG icon. Step 3, page 21
Not ready (Instrument Status window device state) p.10 ↗ Device is not ready for acquisition. Monitor device status in the Instrument Status window and review System Logbook for events and errors. Step 1, page 10