Agilent 6400 Series Triple Quadrupole LC/MS System Quick Start Guide
Technical Reference Summary
Covered Models & Document Scope
Cubre el sistema LC/MS de triple cuadrupolo Agilent 6400 Series. Modelos compatibles en Data Acquisition B.07.00: 6420A, 6430A, 6460A, 6460C, 6490A, 6495A. Modelos de LC compatibles: 1100, 1200, 1260, 1290, HTS, HTC. Los 6490 y 6495 incluyen iFunnel Technology; el 6495 admite resoluciones Unit, Wide y Widest y no admite autotune Fast Scan.
Section-by-Section Technical Breakdown
Describe cómo iniciar el programa MassHunter Data Acquisition, las ocho ventanas principales y cómo mostrar/ocultar y acoplar/desacoplar ventanas. Explica la codificación por colores de la ventana Instrument Status y las funciones de las ventanas Actuals, Chromatogram Plot, Spectrum Plot, Method Editor, Sample Run, Worklist y Tune.
- Double-click the Data Acquisition icon on the Desktop to start the program; software engines start automatically and can be restarted via Acq System Launcher > Start Engines.
- Up to seven windows can be shown at once; windows can be floated by double-clicking the title bar and docked again.
- Instrument Status window shows device status as Error, Not ready, Pre-run, Post-run, Running, Injecting, Idle, Offline, or Standby with color coding.
- Tune window is only visible in the Tune context; Checktune and Autotune reports can be printed via Create Tune Report.
Cubre el cambio del flujo de LC a desecho, la purga de la bomba de LC, el acondicionamiento/equilibrado de la columna, la configuración del monitoreo de actuals en tiempo real y la configuración de las visualizaciones de gráficos en tiempo real. Incluye cómo establecer rangos de parámetros para que los valores fuera de límite se muestren en rojo.
- When not acquiring data, switch the LC stream away from the MS ion source to waste via right-click QQQ device > LC > Waste.
- Purge the LC pump according to the pump User Guide.
- Type LC parameters and click Apply to download them to the LC; monitor baseline to confirm column equilibration.
- Actuals can be configured via right-click Actuals list > Setup; numeric parameters can have limits that turn the background red when exceeded.
Describe la realización de Checktune, Autotune o Manual Tune, incluidos los tiempos esperados, las fuentes de iones compatibles y las acciones correctivas si Checktune falla. También cubre las limitaciones de Fast Scan Autotune y el cambio del flujo de LC al MS.
- Checktune takes approximately 3 minutes per polarity and evaluates mass accuracy and resolution; run it regularly.
- Checktune can be run with ESI, AJS ESI, MMI and HPLC-Chip sources.
- If Checktune fails, use Manual Tune: select Peak Width (Unit, Wide, Widest) on MS1 or MS2 tab and click Adjust Gain & Offset, then save the autotune file.
- Autotune takes approximately 30 minutes per ionization mode (25 minutes for 6490/6495); 6490/6495 Autotune only with AJS ESI source.
- Fast Scan acquisition is only supported on the 6490 for MS2 Scan and Product Ion scan; not supported on 6495.
Guía la configuración de un método de adquisición, incluidos los valores de los módulos de LC, los tipos de escaneo y segmentos del Triple Quad, las señales de cromatograma, las curvas de instrumento almacenadas, los parámetros de DA, las propiedades del método y la ejecución de muestras interactivas y listas de trabajo. Incluye los modos de ejecución bloqueado/desbloqueado y el comportamiento de Override DA Method.
- Scan segments table is cleared when Scan Type changes; transitions can be copied and pasted when changing from MRM to Dynamic MRM or Triggered MRM.
- Fragmentor voltage cannot be set in Acquisition for 6490 or 6495; the tune file value is always used.
- A Data Analysis method contains acquisition parameters with Qual Automation and/or Quant Automation check boxes marked.
- Locked mode prevents changing method or sample parameters during a run and prevents overwriting the data file.
- Worklist can run Acquisition Only, Both Acquisition and DA, or DA Only; Override DA Method column can specify a different DA method.
Describe el uso del programa Qualitative Analysis para revisar los resultados, seleccionar iones precursor/producto para MRM, encontrar e identificar compuestos y realizar la extracción de características moleculares. Describe el uso del programa Quantitative Analysis para configurar lotes y métodos, revisar los resultados de Batch-at-a-Glance y recuantificar utilizando mejores ajustes de calibración.
- Qualitative Analysis supports acquisition method development, MRM ion selection, compound finding/identification, and molecular feature extraction.
- Quantitative Analysis supports batch and method setup for automatic quantitation, Batch-at-a-Glance review, and outlier-based requantitation.
- Familiarization Guides and online Help provide exercises for both programs.
Key Integration, Operating & Safety Requirements
| Specification / Condition | Engineering Implication | Aplica a |
|---|---|---|
| Dynamic MRM puede monitorear hasta 4000 transiciones MRM. p.1 ↗ | Method design must stay within this transition limit when using Dynamic MRM. | 6400 Series Triple Quadrupole LC/MS |
| Checktune tarda aproximadamente 3 minutos por polaridad. p.3 ↗ | Schedule regular Checktune runs; budget about 6 minutes for both polarities. | 6400 Series |
| Autotune tarda aproximadamente 30 minutos por modo de ionización para todos los modelos excepto 6490 y 6495; 6490 y 6495 tardan aproximadamente 25 minutos por modo de ionización. p.3 ↗ | Plan instrument downtime accordingly; Autotune should only be run when necessary. | 6400 Series; 6490/6495 exception |
| Autotune desde los valores predeterminados de fábrica tarda aproximadamente 30 minutos por polaridad (todos los modelos excepto 6490/6495) o aproximadamente 25 minutos por modo de ionización (6490/6495). p.3 ↗ | Use Start from Factory Defaults only if normal Autotune fails; allow extra time. | 6400 Series; 6490/6495 exception |
| Checktune se puede ejecutar con fuentes ESI, AJS ESI, MMI y HPLC-Chip. p.3 ↗ | Source selection must match the installed ion source before Checktune. | 6400 Series |
| Para todos los instrumentos excepto 6490 y 6495, Autotune se puede ejecutar con fuentes AJS ESI, MMI y HPLC-Chip; con 6490 y 6495, Autotune solo con fuente AJS ESI. p.3 ↗ | 6490/6495 users must use AJS ESI for Autotune; other sources are not supported for Autotune on these models. | 6400 Series; 6490/6495 |
| Si Checktune falla, seleccione Peak Width (Unit, Wide o Widest) en la pestaña MS1 o MS2 y haga clic en Adjust Gain & Offset; si tiene éxito, guarde el archivo de autotune. p.3 ↗ | This is the first corrective action before running a full Autotune. | 6400 Series |
| La adquisición Fast Scan solo es compatible con el 6490 con MS2 Scan y Product Ion scan; el autotune Fast Scan utiliza resolución Wide (1.2), Samples = 1 y tamaño de paso 0.2. p.3 ↗ | Do not attempt Fast Scan on other models; for 6495 increase step size to 0.3 m/z for faster scan rate. | 6490; 6495 |
| El voltaje Fragmentor no se puede establecer en Acquisition para 6490 o 6495; siempre utiliza el valor del archivo de tune. p.4 ↗ | Method development for 6490/6495 must manage fragmentor via the tune file, not acquisition parameters. | 6490, 6495 |
| La tabla Scan segments se borra cuando se cambia el Scan Type; las transiciones se pueden copiar y pegar de MRM a Dynamic MRM o Triggered MRM. p.4 ↗ | Save or copy transitions before changing scan type to avoid losing method data. | 6400 Series |
| El modo bloqueado impide que cualquier persona cambie el método o los parámetros de la muestra durante una ejecución y evita sobrescribir el archivo de datos en Data Acquisition. p.4 ↗ | Use locked mode for regulated or unattended runs to protect data integrity. | 6400 Series |
| La retención del System Logbook se puede establecer de 1 semana a 1 año mediante Tools > Purge Settings. p.3 ↗ | Configure retention to meet laboratory record-keeping requirements. | 6400 Series Data Acquisition |
| Cuando no se están adquiriendo datos, cambie el flujo de LC a desecho mediante clic derecho en el dispositivo QQQ > LC > Waste. p.2 ↗ | Prevents unnecessary contamination of the MS ion source during column conditioning. | 6400 Series with LC |
| A los parámetros de Actuals se les pueden asignar límites numéricos; si el valor está fuera de los límites, el fondo se establece en rojo. p.2 ↗ | Use Actuals limits for at-a-glance monitoring of critical MS and LC parameters such as heater and vacuum pressure. | 6400 Series Data Acquisition |
| El 6495 admite resoluciones Unit, Wide y Widest; el autotune Fast scan no es compatible con el 6495. p.2 ↗ | 6495 method development can use all three resolution modes but must not rely on Fast Scan autotune. | 6495 |
| Los 6490 y 6495 contienen iFunnel Technology, incluidos Dual Offset Ion Funnel, Agilent Jet Stream Technology y un ensamblaje de desolvatación más corto con Hexabore Capillary. p.1 ↗ | These models provide more efficient ion sampling; method sensitivity expectations differ from other 6400 models. | 6490, 6495 |
Faults & Troubleshooting
| Código / Síntoma | Possible Cause | Remedy | Note |
|---|---|---|---|
| Checktune fails p.17 ↗ | MS parameters outside limits for specified mass accuracy and resolution | Use Manual Tune tab: select Peak Width (Unit, Wide, or Widest) on MS1 or MS2 tab based on which resolution failed, click Adjust Gain & Offset; if successful, save autotune file. If Checktune fails again, run Autotune. | Step 3, page 17 |
| Autotune fails p.18 ↗ | Tune parameters could not be optimized automatically | Mark Start from Factory Defaults check box and click Autotune; check progress box for reasons; if still unsuccessful, manually tune or call Agilent service engineer. | Step 3, page 18 |
| No reports printed after Autotune p.18 ↗ | Autotune did not complete successfully | Check progress box in lower right side of Autotune tab for reasons why tune failed; fix problem or call Agilent service engineer with this information. | Step 3, page 18 |
| Instrument Status window shows Red p.8 ↗ | Error status | View System Logbook for logged events and errors via Log icon, Tools > System Logbook Viewer, or taskbar LOG icon. | Table 1, page 8; page 19 |
| Instrument Status window shows Yellow p.8 ↗ | Not ready status | Wait for instrument to become ready; check device status and logbook if persists. | Table 1, page 8 |
| Instrument Status window shows Dark gray p.8 ↗ | Offline status | Check device connection and configuration; reconfigure instrument if LC modules changed. | Table 1, page 8 |
Technical Data
| Parameter | Value | Condición |
|---|---|---|
| Maximum MRM transitions (Dynamic MRM) | 4000 transitions p.1 ↗ | Dynamic MRM |
| Checktune duration | approximately 3 minutes p.16 ↗ | per polarity |
| Autotune duration | approximately 30 minutes p.17 ↗ | per ionization mode; all models except 6490 and 6495 |
| Autotune duration | approximately 25 minutes p.17 ↗ | per ionization mode; 6490 and 6495 |
| Autotune from factory defaults duration | approximately 30 minutes p.17 ↗ | per polarity; all models except 6490 and 6495 |
| Autotune from factory defaults duration | approximately 25 minutes p.17 ↗ | per ionization mode; 6490 and 6495 |
| Fast Scan step size | 0.2 m/z p.18 ↗ | 6490 Fast Scan Autotune; Wide (1.2) resolution, Samples = 1 |
| Fast Scan step size | 0.3 m/z p.18 ↗ | 6495 (Fast Scan not supported; increased step size for faster scan rate) |
| System Logbook retention period | 1 week to 1 year p.19 ↗ | Tools > Purge Settings |