Induztr
Resumen técnico Visor de documentos Modelos relacionados

Agilent 6200 Series TOF and 6500 Series Q-TOF LC/MS System Quick Start Guide

Technical Reference Summary

Covered Models & Document Scope

Abarca los sistemas LC/MS Agilent de la Serie 6200 TOF (6224, 6230) y de la Serie 6500 Q-TOF (6520B, 6530A/B, 6538A, 6540A/B, 6545A, 6550A, 6560A Ion Mobility Q-TOF) con el software MassHunter Workstation B.07.00; incluye las opciones de fuente ESI, Dual ESI, AJS ESI, Dual AJS ESI, Multimode, APPI, APCI.

Section-by-Section Technical Breakdown

pp. 9-14
Paso 1. Iniciar el software de adquisición de datos

Describe el inicio de MassHunter Data Acquisition, las siete ventanas principales (Instrument Status, Actuals, Chromatogram Plot, Spectrum Plot, Method Editor, Sample Run, Worklist, Tune), el comportamiento de mostrar/ocultar y flotar/acoplar ventanas, y la codificación por colores del estado del instrumento. También explica las funciones de la ventana Tune y la selección del modo de instrumento para el 6560 Ion Mobility Q-TOF.

  • Double-click the Data Acquisition icon to start; software engines start automatically, or right-click Acq System Launcher and click Start Engines to restart.
  • Instrument Status window color coding: Red=Error, Yellow=Not ready, Purple=Pre-run/post-run, Blue=Running/injecting, Green=Idle, Dark gray=Offline, Light gray=Standby.
  • Tune window: use automated tuning algorithms or manual tune; Agilent recommends manual tuning only for ion source and optics 1, not parameters after the collision cell.
  • For 6560 Ion Mobility Q-TOF, the Tune window contains Acquisition Mode selection (IM-QTOF or QTOF-Only).
  • For 6545 or 6560 Q-TOF, additional small molecule autotune options are available.
pp. 16-18
Paso 2. Preparar los módulos LC

Cubre el cambio del flujo LC a desecho durante el acondicionamiento/equilibrado de la columna, el purgado de la bomba LC, el acondicionamiento de la columna y la configuración del monitoreo de valores reales en tiempo real. Enfatiza el monitoreo de la estabilidad de la línea base antes de cambiar el flujo al MS.

  • Switch LC Stream to Waste in the Method Editor General tab before conditioning the column; click Apply Now to send only the LC eluent value.
  • Purge the LC pump per the pump User Guide, then condition or equilibrate the column.
  • Set up Actuals window via right-click > Setup to monitor selected instrument parameters with custom colors and conditional formatting.
  • Monitor baseline and adjust plots to confirm column equilibration and stable baseline.
pp. 20-36
Paso 3. Preparar el instrumento TOF y Q-TOF

Detalla los procedimientos de ajuste y calibración para instrumentos TOF y Q-TOF, incluidos Classic Autotune y SWARM autotune, las fuentes compatibles por modelo, los requisitos de dilución de la mezcla de ajuste, la calibración de masas y el cambio del flujo LC al MS. Proporciona restricciones específicas por modelo para el modo de instrumento, el rango de masas y el modo slicer.

  • Tune the instrument after first use, maintenance, service, or pump-down/restart; calibrate mass-axis regularly.
  • Classic Autotune: Set Detector Gain, Standard Tune, or Initial Tune require Instrument Mode = Extended Dynamic Range and Mass Range = Standard (3200 m/z).
  • SWARM autotune (6545/6560): System Tune requires Standard (3200 m/z); Transmission Tune available for Low (1700 m/z) and takes ~6-10 minutes.
  • Supported sources for all autotunes vary by model (see Table 1); nanoESI, Dual nanoESI, HPLC-Chip, MALDI, and GC-QTOF sources cannot run automated tunes.
  • Tune mix dilution: 6530A with Dual AJS ESI or 6540 uses 1:10 diluted for positive TOF tune and 1:40 for negative; 6520B or 6530 with Dual ESI uses undiluted.
  • For 6230 TOF with AJS ESI or Dual AJS ESI, use 1:10 dilution for positive and 1:40 for negative; do not dilute for Dual ESI on 6224 TOF.
  • Recalibrate if Instrument Mode, Mass Range, or Slicer Mode changes, or if calibrant ion abundances exceed ~480,000 (6538/6540) or ~650,000 (other Q-TOF/TOF except 6550).
  • Switch LC stream from Waste to MS after tuning and stable baseline.
pp. 37-38
Paso 4. Configurar y ejecutar un método

Explica la configuración de métodos MassHunter que contienen parámetros de adquisición, cualitativos y cuantitativos, y la ejecución de muestras individuales o listas de trabajo. Cubre las opciones de método solo para adquisición, solo para análisis de datos o ambos, y hace referencia a los ejercicios de la Familiarization Guide.

  • A method can contain acquisition parameters, qualitative analysis parameters, quantitative analysis parameters, or all three.
  • In worklist runs, select Acquisition Only, Both Acquisition and DA, or DA Only in Worklist Run Parameters.
  • Mark Qual Automation or Quant Automation check boxes in the DA tab to run data analysis automatically after acquisition.
  • Set Instrument State tab options in the Tune window before editing or running a method.
  • Use TOF/Q-TOF Familiarization Guide Exercises 1-5 for method setup, IM-QTOF mode, IM-MS optimization, and CCS calculations.

Key Integration, Operating & Safety Requirements

Specification / Condition Engineering Implication Aplica a
Classic Autotune Set Detector Gain, Standard Tune e Initial Tune requieren Instrument Mode = Extended Dynamic Range y Mass Range = Standard (3200 m/z). p.3 ↗ These autotunes are grayed out if a different mode or source is selected; set these values before tuning. 6200 Series TOF and 6500 Series Q-TOF (Classic Autotune models)
SWARM System Tune requiere Mass Range = Standard (3200 m/z); Transmission Tune está disponible para Low (1700 m/z) y tarda aproximadamente 6-10 minutos. p.3 ↗ For small molecule work at Low mass range, use Transmission Tune; System Tune is not available. 6545 and 6560 Q-TOF
Para 6530A con Dual AJS ESI o 6540, el ajuste TOF en iones positivos utiliza mezcla de ajuste diluida 1:10 y el ajuste TOF en iones negativos utiliza mezcla de ajuste diluida 1:40. p.3 ↗ Prepare correct tune mix dilution to avoid autotune failure. 6530A with Dual AJS ESI, 6540
Para 6520B o 6530 con Dual ESI, tanto los ajustes TOF en iones positivos como en negativos utilizan mezcla de ajuste sin diluir. p.3 ↗ Do not dilute tune mix for these configurations. 6520B, 6530 with Dual ESI
Para 6230 TOF con AJS ESI o Dual AJS ESI, utilice dilución 1:10 para el ajuste en iones positivos y 1:40 para el ajuste en iones negativos. p.3 ↗ Dilution is required for both polarities with AJS sources on 6230. 6230 TOF with AJS ESI or Dual AJS ESI
Para 6224 TOF con Dual ESI, no diluya la mezcla de ajuste para el ajuste en iones positivos; se producen problemas si se diluye. p.3 ↗ Use undiluted tune mix for positive ion tuning on 6224 with Dual ESI. 6224 TOF with Dual ESI
Recalibre si las abundancias de los iones calibradores superan aproximadamente 480,000 para 6538/6540 Q-TOF o aproximadamente 650,000 para otros instrumentos Q-TOF y TOF (excepto 6550). p.3 ↗ Dilute the tune calibrant before recalibration to maintain mass accuracy. All TOF/Q-TOF except 6550 (which always uses 1:10 dilution)
Duración de Initial Tune: hasta 60 minutos por polaridad para 6538A, 6540A, 6550A Q-TOF; hasta 30 minutos por polaridad para otros instrumentos Q-TOF y TOF. p.3 ↗ Plan sufficient time for initial tuning based on model. 6200 Series TOF and 6500 Series Q-TOF
Quick Tune tarda de 7 a 10 minutos; Standard Tune tarda de 10 a 15 minutos para TOF y de 10 a 15 minutos para cuadrupolo. p.3 ↗ Use Quick Tune for faster limited-parameter tuning; Standard Tune for more parameters. Classic Autotune models
Para aplicaciones de moléculas pequeñas en 6550 Q-TOF, ajuste Quad AMU a 100 en polaridad positiva y 90 en polaridad negativa antes del autotune, y seleccione el rango de masas Low (1700 m/z). p.3 ↗ Required for proper small molecule tuning on 6550. 6550 Q-TOF
Para 6545 o 6560 Q-TOF con rango de masas Low (1700 m/z), las opciones de autotune de baja masa incluyen 50-250 m/z y 50-750 m/z (no disponible para 6560); marcar Fragile Ions reduce el voltaje del fragmentador. p.3 ↗ Select appropriate low mass tune for fragile molecules to minimize fragmentation. 6545 and 6560 Q-TOF
Fuentes compatibles para todos los autotunes: 6224 TOF: ESI, Dual ESI; 6230 TOF: ESI, Dual ESI, AJS ESI, Dual AJS ESI; 6520B: ESI, Dual ESI; 6530A/B: ESI, Dual ESI, AJS ESI, Dual AJS ESI; 6538: ESI, Dual ESI; 6540A/B, 6545: ESI, Dual ESI, AJS ESI, Dual AJS ESI; 6550: ESI, Dual ESI, AJS ESI, Dual AJS ESI; 6560: Dual ESI, Dual AJS ESI. p.3 ↗ Automated tunes cannot run with unsupported sources such as nanoESI, MALDI, or GC-QTOF. Per model as listed
Para 6545 con Fast Polarity Switching Enabled, solo se puede ejecutar Mass Calibration/Check o FPS System Tune; para TOF y otros Q-TOF, solo Mass Calibration/Check o FPS Initial Auto Tune. p.3 ↗ Fast Polarity Switching restricts available autotune options. 6545 Q-TOF and other TOF/Q-TOF
Seleccione High Resolution para Slicer Mode antes de Initial Auto Tune o System Tune para obtener los mejores resultados de ajuste. p.3 ↗ High Resolution slicer mode is required for these tunes. All TOF/Q-TOF with slicer mode option
El ajuste Mass Calibration/Check tarda unos minutos para TOF y de 2 a 5 minutos para el cuadrupolo. p.3 ↗ Allow adequate time for calibration checks. All TOF/Q-TOF
Para los modelos 6530A/B, la función Adjust abundances for optimal calibration ajusta automáticamente el voltaje del fragmentador si las masas de calibración están fuera del rango de 50 a 650K. p.3 ↗ If fragmentor cannot reduce abundance below 650K, dilute calibrant and retry. 6530A/B

Faults & Troubleshooting

Código / Síntoma Possible Cause Remedy Note
Autotune can fail p.23 ↗ Tuning mix not diluted for 6560A, 6550A, 6545A, 6540A, or 6530A with Agilent Jet Stream ESI or Dual AJS ESI source. Dilute the tuning mix as instructed in the Installation Guide and online Help. Diluting the ESI-L Tune Mix, page 23
Problems occur if you dilute the tune mix and tune for positive ion p.24 ↗ Diluting tune mix on 6224 TOF with Dual ESI source. Do not dilute the tune mix for the Dual ESI source on the 6224 TOF. TOF section, page 24
Calibration masses detected out of the 50 to 650K range p.25 ↗ Calibrant ion abundance too high or low for optimal calibration. System automatically adjusts fragmentor voltage; if cannot reduce below 650K, dilute the calibrant and retry calibration or autotune. 6530A/B only, page 25
Check tune results are not acceptable p.27 ↗ Mass calibration or tune parameters out of specification. Continue with Transmission Tune (6545/6560) or Quick Tune/Standard Tune/Initial Auto Tune (Classic); if still unacceptable, contact Agilent Field Support. Step 3, pages 27-34
Standard Tune produces unacceptable results p.29 ↗ Tune parameters not optimized. Run an Initial Auto Tune, then adjust Collision Cell Gas Pressure; if still failing, contact Agilent Field Support. Step 3, page 29
System Tune results are not acceptable p.34 ↗ SWARM autotune unable to achieve acceptable performance. Contact your local field service engineer. Step 3, page 34