Operating Instructions — VGD 4 vacuum pump (BA 234-EN, ed. 1.6 3.12.2019, EN)
Technical Reference Summary
Covered Models & Document Scope
Cubre las bombas de vacío rotativas de paletas lubricadas con aceite V-VGD 4, V-VGD 8, V-VGD 11, V-VGD 16 y V-VGD 21 (Serie V, Edición 1.6, BA 234-EN). Las variantes difieren en la capacidad de aspiración, el vacío final, el tipo/viscosidad del aceite (ISO VG 32 para V-VGD 4–16, ISO VG 46 para V-VGD 21), la válvula de lastre de gas (solo V-VGD 16 y 21) y el montaje (V-VGD 4 no atornillada a la superficie de apoyo).
Section-by-Section Technical Breakdown
Describe la construcción y el principio de funcionamiento de la serie V-VGD. Las bombas tienen un filtro de malla fina en el lado de aspiración y un separador de aceite/niebla de aceite en el lado de salida que devuelve el aceite a la circulación. El motor y la bomba comparten un eje común; una válvula de retención integral impide la ventilación del sistema evacuado después de la parada.
- Fine mesh filter on suction side; oil and oil mist separator on outlet side
- Motor fan cools motor and pump housing; motor and pump have common shaft
- Integral non-return valve prevents evacuated system from being ventilated after pump stop
- If machine has been idle for more than two minutes, connected pipe should be ventilated to atmospheric pressure
- Gas ballast valve (V-VGD 16 and 21) prevents water vapour condensation inside the pump at operating temperature
Define el uso previsto y los límites operativos de las bombas. La capacidad de aspiración a 50 Hz es de 4, 8, 10, 15 y 20 m³/h para V-VGD 4, 8, 11, 16 y 21 respectivamente. Las bombas son adecuadas para la evacuación de sistemas cerrados pero no para funcionamiento continuo; se especifican los límites de intervalo de conmutación y el volumen máximo evacuado.
- Suction capacity with unrestricted suction at 50 Hz: 4, 8, 10, 15, 20 m³/h (V-VGD 4, 8, 11, 16, 21)
- Not suitable for continuous operation
- Switching interval may not exceed 12 times per hour (start/stop) at 2–100 mbar (abs.) for V-VGD 4, 8, 11, 16 and 1.5–100 mbar (abs.) for V-VGD 21
- Volume to be evacuated must be no more than 2 % of nominal suction capacity
- If installed in open air, unit must be protected from environmental influences (e.g. protective roof)
Cubre la preparación, la instalación mecánica, la conexión de tuberías, el llenado de aceite y la conexión del motor. La máquina debe instalarse horizontalmente (inclinación máxima de 10° en todas las direcciones) y atornillarse a la superficie de apoyo (no para VGD 4). La instalación eléctrica debe ser realizada por un electricista cualificado observando EN 60204.
- Machine may only be operated when set up horizontally (max. inclination 10° in all directions)
- Machine must be screwed to bearing surface to secure against tipping and slipping (not for VGD 4)
- Bearing surface must be plane, even, able to carry weight, and at least same size as machine
- Output reduction noticeable when installed at more than 1000 m above sea level
- Counter pressures on outlet side only permissible up to +0.1 bar
- Only screw in pipes by hand; use flexible connections if necessary
- Fill lubricating oil between max. and min. mark on oil sight glass
- Motor protection switch required; connecting cable installed via cable fitting for strain relief
- Permissible tolerances: ±5 % voltage deviation, ±2 % frequency deviation
- Motors comply with DIN EN 60034, protection class IP 54, insulation class B
Describe las comprobaciones de puesta en marcha, la verificación del sentido de giro, la puesta fuera de servicio/almacenamiento y la puesta en marcha de nuevo. La temperatura ambiente de funcionamiento es de 10–40 °C y la humedad debe ser inferior al 85 %. El sentido de giro debe comprobarse con un indicador de secuencia de fases; el ventilador del motor debe girar en sentido antihorario visto desde el ventilador.
- Operating ambient temperature 10–40 °C; humidity less than 85 %
- Use phase sequence indicator to check clockwise rotating field
- Start motor briefly (max. two seconds) to check direction; when looking at motor fan, it must rotate anti-clockwise
- After correcting rotation direction, run motor for 2 minutes then top up oil to upper edge of sight glass; filling point must not be open when pump is running
- Decommissioning: switch off, close cut-off devices, disconnect from electricity, depressurise, remove pipes, seal connections with adhesive foil
- Re-commissioning: check condition, drain preserving agents
Especifica los intervalos de mantenimiento y los procedimientos para el filtrado de aire, la lubricación y la sustitución del elemento separador de aceite. Se requiere un mantenimiento regular para garantizar la seguridad operativa. La unidad completa debe mantenerse siempre limpia.
- Monthly: check pipes and screws for leaks, check terminal box and cable inlet holes for leaks, clean ventilation slots and motor cooling ribs
- Clean intake air filter depending on how dirty the discharged medium is
- Daily: check oil level
- First oil change after 500 h; subsequent oil changes every 1,500–3,000 h
- Change oil separator element every 1,500–3,000 operating hours
- Oil viscosity must comply with ISO VG 32 (V-VGD 4–16) or ISO VG 46 (V-VGD 21) as per DIN ISO 3448
- Recommended oils: SUPER-LUBE 32 for V-VGD 4–16, SUPER-LUBE 46 for V-VGD 21
- Always change oil when machine is at operating temperature and in an atmospherically ventilated area
- If changing oil type, empty oil removing device housing and oil cooler completely
- Oil separator element cannot be cleaned; replace every 1,500–3,000 operating hours
- Lightly oil O-ring on new oil separator element before fitting
Proporciona el nivel de presión sonora, el peso, las dimensiones, el vacío final, el tamaño de la conexión de vacío y la cantidad correcta de aceite para cada modelo. Los valores se dan para funcionamiento a 50 Hz; la longitud y el peso pueden diferir según el diseño del motor.
- Sound pressure level (max.) at 50 Hz: 58 dB(A) V-VGD 4, 62 dB(A) V-VGD 8 and 11, 65 dB(A) V-VGD 16 and 21 (tolerance ±3 dB(A), EN ISO 3744)
- Weight: 5.8 kg (V-VGD 4), 11.5 kg (V-VGD 8 and 11), 16 kg (V-VGD 16), 19.5 kg (V-VGD 21)
- Ultimate vacuum: 2 mbar (abs.) for V-VGD 4, 8, 11, 16; 1.5 mbar (abs.) for V-VGD 21
- Vacuum connection: Ø 13 mm (V-VGD 4), Ø 20 mm (V-VGD 8, 11, 16, 21)
- Correct amount of oil: 0.13 l (V-VGD 4), 0.25 l (V-VGD 8 and 11), 0.45 l (V-VGD 16 and 21)
Key Integration, Operating & Safety Requirements
| Specification / Condition | Engineering Implication | Aplica a |
|---|---|---|
| La capacidad de aspiración con aspiración sin restricciones a 50 Hz es de 4 m³/h (V-VGD 4), 8 m³/h (V-VGD 8), 10 m³/h (V-VGD 11), 15 m³/h (V-VGD 16) y 20 m³/h (V-VGD 21). p.16 ↗ | Used for sizing the pump to the required evacuation flow; note that actual capacity is reduced by narrow or long inlet pipes. | V-VGD 4, 8, 11, 16, 21 |
| El intervalo de conmutación no puede superar 12 veces por hora (arranque/parada) en un rango de presión de 2–100 mbar (abs.) para V-VGD 4, 8, 11 y 16 y de 1,5–100 mbar (abs.) para V-VGD 21. p.16 ↗ | Frequent cycling outside these ranges risks oil leaking through the outlet opening and exceeding motor winding/bearing temperature limits. | V-VGD 4, 8, 11, 16, 21 |
| Al evacuar sistemas cerrados, el volumen a evacuar no debe ser superior al 2 % de la capacidad de aspiración nominal de la bomba de vacío. p.16 ↗ | Limits the allowable connected volume for intermittent evacuation; larger volumes require a larger pump or different operating mode. | V-VGD 4, 8, 11, 16, 21 |
| La máquina solo debe operarse a una temperatura ambiente y una temperatura de aspiración entre 10 y 40 °C. p.7 ↗ | Installation location and process gas temperature must be controlled within this range; contact manufacturer for temperatures outside this range. | V-VGD 4, 8, 11, 16, 21 |
| Las contrapresiones en el lado de salida solo son admisibles hasta +0,1 bar. p.18 ↗ | Exhaust lines must be sized and routed to avoid back pressure exceeding 0.1 bar; never close or constrict exhaust air openings. | V-VGD 4, 8, 11, 16, 21 |
| La desviación de tensión admisible es de ±5 % y la desviación de frecuencia es de ±2 %. p.19 ↗ | Mains supply must be within these tolerances of the motor data plate values to avoid loss of power or damage. | V-VGD 4, 8, 11, 16, 21 |
| Los motores cumplen con DIN EN 60034, clase de protección IP 54 y clase de aislamiento B. p.19 ↗ | Electrical installation must be suitable for IP 54 environment; motor protection switch required and connecting cable installed via cable fitting for strain relief. | V-VGD 4, 8, 11, 16, 21 |
| Primer cambio de aceite después de 500 horas de funcionamiento; cambios de aceite posteriores después de 1.500–3.000 horas de funcionamiento. p.24 ↗ | Maintenance schedule must include initial 500 h oil change and recurring 1,500–3,000 h changes; reduce intervals depending on contamination of discharged medium. | V-VGD 4, 8, 11, 16, 21 |
| El elemento separador de aceite debe sustituirse cada 1.500–3.000 horas de funcionamiento; no se puede limpiar. p.25 ↗ | Plan spare part replacement at these intervals; contaminated element increases power consumption and pump temperature and may cause oil ignition in extreme cases. | V-VGD 4, 8, 11, 16, 21 |
| La viscosidad del aceite debe cumplir con ISO VG 32 (V-VGD 4–16) o ISO VG 46 (V-VGD 21) según DIN ISO 3448. p.24 ↗ | Use only oil of correct viscosity; recommended Elmo Rietschle oils are SUPER-LUBE 32 for V-VGD 4–16 and SUPER-LUBE 46 for V-VGD 21. | V-VGD 4, 8, 11, 16, 21 |
| Cantidad correcta de aceite: 0,13 l (V-VGD 4), 0,25 l (V-VGD 8 y 11), 0,45 l (V-VGD 16 y 21). p.30 ↗ | Oil fill quantity for initial fill and refill; oil level must always be visible between max. and min. mark on sight glass. | V-VGD 4, 8, 11, 16, 21 |
| Vacío final: 2 mbar (abs.) para V-VGD 4, 8, 11, 16; 1,5 mbar (abs.) para V-VGD 21. p.30 ↗ | Defines the maximum vacuum achievable with suction opening closed; selection must consider required final pressure. | V-VGD 4, 8, 11, 16, 21 |
| Conexión de vacío: Ø 13 mm (V-VGD 4), Ø 20 mm (V-VGD 8, 11, 16, 21). p.30 ↗ | Pipework and fittings must match these connection sizes; undersized inlet pipe reduces pumping capacity. | V-VGD 4, 8, 11, 16, 21 |
| Nivel de presión sonora (máx.) a 50 Hz: 58 dB(A) V-VGD 4, 62 dB(A) V-VGD 8 y 11, 65 dB(A) V-VGD 16 y 21 (tolerancia ±3 dB(A), EN ISO 3744). p.30 ↗ | Use ear protection when spending long time near running machine; consider acoustic measures for noise-sensitive installations. | V-VGD 4, 8, 11, 16, 21 |
| La máquina solo puede operarse cuando está instalada horizontalmente con una inclinación máxima de 10° en todas las direcciones. p.17 ↗ | Mounting surface must be plane and even; machine must be screwed to bearing surface (not for VGD 4) to secure against tipping and slipping. | V-VGD 4, 8, 11, 16, 21 |
| Se nota una reducción de la potencia cuando se instala a más de 1000 m sobre el nivel del mar. p.17 ↗ | For high-altitude installations, contact manufacturer for suitability and possible derating. | V-VGD 4, 8, 11, 16, 21 |
| Rango de temperatura de almacenamiento: -10 °C a +60 °C; humedad relativa 0 % a 80 %. p.11 ↗ | Storage area must meet these conditions; for long-term storage (more than 3 months) use preservation oil rather than operating oil. | V-VGD 4, 8, 11, 16, 21 |
| Si la máquina ha estado inactiva durante más de dos minutos, la tubería conectada debe ventilarse a la presión atmosférica. p.16 ↗ | Prevents oil from being drawn into the evacuated system due to vacuum remaining in the pipe after pump stop. | V-VGD 4, 8, 11, 16, 21 |
| La válvula de lastre de gas solo está prevista en V-VGD 16 y V-VGD 21. p.16 ↗ | For processes with water vapour, select V-VGD 16 or 21; gas ballast prevents condensation inside the pump when low amounts of steam are sucked in at operating temperature. | V-VGD 16, V-VGD 21 |
Faults & Troubleshooting
| Código / Síntoma | Possible Cause | Remedy | Note |
|---|---|---|---|
| Machine is switched off by the motor protection switch p.27 ↗ | Mains voltage/ Frequency does not correspond with the motor data | Check by qualified electrician | Section 5.5 |
| Machine is switched off by the motor protection switch p.27 ↗ | Connection to motor terminal board is not correct | Check by qualified electrician | Section 5.5 |
| Machine is switched off by the motor protection switch p.27 ↗ | Motor protection switch is not set correctly | Check by qualified electrician | Section 5.5 |
| Machine is switched off by the motor protection switch p.27 ↗ | Motor protection switch is triggered too quickly | Use a motor protection switch with an overload-dependent delayed switch off that takes into consideration the short term excess current at start up (version with short circuit and overload trigger as per IEC 60947-4-1 or VDE 0660 Part 102) | |
| Machine is switched off by the motor protection switch p.27 ↗ | Vacuum pump or its oil is too cold | Note the ambient temperature and the intake temperature | Section 2.3 |
| Machine is switched off by the motor protection switch p.27 ↗ | The lubricating oil is too viscous | The oil viscosity must comply with ISO VG 32 / 46 (see pump type) as per DIN ISO 3448 | Section 7.2.2 |
| Machine is switched off by the motor protection switch p.27 ↗ | The oil separator element is dirty. | Change the oil separator element | Section 7.2.3 |
| Machine is switched off by the motor protection switch p.27 ↗ | The back pressure is too high when the exhaust air is being discharged. | Check the hose or the pipe | Section 5.3 |
| Suction capacity is insufficient p.27 ↗ | The suction pipe is too long or too narrow | Check the hose or the pipe | Section 5.3 |
| Suction capacity is insufficient p.27 ↗ | Leak on the suction side of the vacuum pump or in the system | Check the pipework and screw connections for leaks and to ensure that they are firmly seated. | Section 7.2 |
| Suction capacity is insufficient p.27 ↗ | The intake filter is dirty | Clean or replace the intake filter | Section 7.2.1 |
| Final pressure (max. vacuum) is not reached p.27 ↗ | Leak on the suction side of the vacuum pump or in the system | Check the pipework and screw connections for leaks and to ensure that they are firmly seated. | Section 7.2 |
| Final pressure (max. vacuum) is not reached p.27 ↗ | Incorrect oil viscosity | The oil viscosity must comply with ISO VG 32 / 46 (see pump type) as per DIN ISO 3448 | Section 7.2.2 |
| Machine gets too hot p.28 ↗ | Ambient or intake temperature is too high | Ensure it is being used properly | Section 2.3 |
| Machine gets too hot p.28 ↗ | Cooling air supply is obstructed | Check environmental conditions | Section 5.1 |
| Machine gets too hot p.28 ↗ | Cooling air supply is obstructed | Clean ventilation slots | Section 7.2 |
| Machine gets too hot p.28 ↗ | The lubricating oil is too viscous | The oil viscosity must comply with ISO VG 32 / 46 (see pump type) as per DIN ISO 3448 | Section 7.2.2 |
| Machine gets too hot p.28 ↗ | The oil separator element is dirty. | Change the oil separator element | Section 7.2.3 |
| Machine gets too hot p.28 ↗ | The back pressure is too high when the exhaust air is being discharged. | Check the hose or the pipe | Section 5.3 |
| Exhaust air contains visible oil mist p.28 ↗ | The oil separator element is not inserted correctly or the O ring is missing | Check that it is correctly seated | Section 7.2.3 |
| Exhaust air contains visible oil mist p.28 ↗ | Unsuitable oil is being used | Use suitable types | Section 7.2.2 |
| Exhaust air contains visible oil mist p.28 ↗ | The oil separator element is dirty. | Change the oil separator element | Section 7.2.3 |
| Exhaust air contains visible oil mist p.28 ↗ | Ambient or intake temperature is too high | Ensure it is being used properly | Section 2.3 |
| Exhaust air contains visible oil mist p.28 ↗ | Cooling air supply is obstructed | Check environmental conditions | Section 5.1 |
| Exhaust air contains visible oil mist p.28 ↗ | Cooling air supply is obstructed | Clean ventilation slots | Section 7.2 |
| The machine makes a abnormal noise (The blades making a hammering noise when starting from cold is normal if it disappears within two minutes as the operating t p.29 ↗ | The pump housing is worn (chatter marks) | Repair by manufacturer or authorised workshop | Elmo Rietschle Service |
| The machine makes a abnormal noise (The blades making a hammering noise when starting from cold is normal if it disappears within two minutes as the operating t p.29 ↗ | Blades are damaged | Repair by manufacturer or authorised workshop | Elmo Rietschle Service |
| The machine makes a abnormal noise (The blades making a hammering noise when starting from cold is normal if it disappears within two minutes as the operating t p.29 ↗ | Vacuum pump or its oil is too cold | Note the ambient temperature and the intake temperature | Section 2.3 |
| The machine makes a abnormal noise (The blades making a hammering noise when starting from cold is normal if it disappears within two minutes as the operating t p.29 ↗ | The lubricating oil is too viscous | The oil viscosity must comply with ISO VG 32 / 46 (see pump type) as per DIN ISO 3448 | Section 7.2.2 |
| Water in lubricating oil p.29 ↗ | Pump sucks in water | Install water interceptor upstream of the pump | |
| Water in lubricating oil p.29 ↗ | The pump sucks in more water vapour than is suitable for its water vapour compatibility | Contact the manufacturer for increased gas ballast | |
| Water in lubricating oil p.29 ↗ | Pump only works for a short time and therefore does not reach its normal operating temperature | Let the pump continue to run with a closed suction side after extracting the water vapour until the water has evaporated from the oil |