Induztr
Resumen técnico Visor de documentos Modelos relacionados

Operating Instructions — (EN)

Technical Reference Summary

Covered Models & Document Scope

Serie L-BV7N de bombas/compresores de anillo líquido, tipos 2BV7060, 2BV7061, 2BV7070 y 2BV7071. Las variantes -2 y -3 se listan para 2BV7060, 2BV7070 y 2BV7071; 2BV7061 se lista como -1. Edición del documento 07.2019, 610.00187.40.000.

Section-by-Section Technical Breakdown

pp. 10-11
Datos técnicos

Datos mecánicos, referencia a los datos eléctricos y condiciones de servicio de la serie L-BV7N. Incluye pesos, distancias mínimas de disipación de calor, niveles de ruido, límites de temperatura, límites de presión, caudales nominales de líquido de servicio y cantidades de llenado para el cebado.

  • Weights range from approx. 20 kg (2BV7060-2) to 68 kg (2BV7071-3).
  • Minimum distance from fan guard to adjacent surface: 34 mm for 2BV7060/2BV7061, 53 mm for 2BV7070/2BV7071.
  • Noise level measured per EN ISO 3744 at 1 m with medium throttling (100 mbar abs.) and connected lines, tolerance ±3 dB(A).
  • Electrical data is given on the drive motor rating plate.
  • Pumped gas/vapor and operating-liquid temperature max. +80 °C; operating-liquid min. +5 °C, nominal +15 °C; ambient +5 to +40 °C.
  • Max. discharge pressure during vacuum-pump operation 1.3 bar abs.; max. permissible pressure in pump-motor unit 8 bar abs.
  • Max. discharge pressure during compressor operation depends on type and frequency (e.g. 2BV7071: 3.5 bar abs. at 50 Hz, 2.2 bar abs. at 60 Hz).
  • Nominal operating-liquid flow rate and priming filling amount are tabulated per type and frequency.
pp. 12
Diseño y método de funcionamiento

Describe el principio de anillo líquido: un impulsor dispuesto excéntricamente en una carcasa cilíndrica con líquido de servicio que forma un anillo giratorio. El gas se aspira por la boca de aspiración, se comprime y se descarga por la boca de descarga.

  • Components: discharge connection (1), operating-liquid port (2), inlet connection (3), impeller (4), housing (5), discharge port (6), inlet port (7), operating liquid (8).
  • Impeller is arranged eccentrically relative to the housing.
  • Operating liquid is fed via the operating-liquid port and discharged together with the pumped gases/vapors via the discharge connection.
  • During rotation the liquid ring is concentric to the housing and eccentric to the impeller, creating increasing cell volume for suction and decreasing volume for compression.
pp. 13
Modos de funcionamiento

Define el funcionamiento autoaspirante y el funcionamiento con alimentación de líquido de servicio (manual o automática). El modo de funcionamiento determina cómo y cuándo se llena la unidad con líquido de servicio y cómo se pone en marcha.

  • Self-priming operation: the pump-motor unit automatically sucks in operating liquid; flow rate is automatically adjusted.
  • Operation with operating-liquid feed: the unit does NOT automatically suck in operating liquid; a nominal operating-liquid flow rate or pre-pressure must be set.
  • Manual operation uses a stop valve to switch operating-liquid feed on and off.
  • Automatic operation uses a solenoid valve that opens when the motor/pump-motor unit is switched on and closes when switched off.
pp. 16-21
Instalación

Requisitos de instalación para el grupo motobomba, incluidos posición de montaje, superficie, holguras de disipación de calor, límite de vibración y atornillado. También cubre la conexión eléctrica del motor y la conexión de tuberías/mangueras.

  • Install on level, stationary surfaces with shaft horizontal; maximum installation height 1000 m above sea level.
  • Comply with minimum distances for heat dissipation from Chapter 4.1.
  • Maximum permissible vibration velocity veff = 4.5 mm/s.
  • Bolt feet to supporting surface: 2BV706 with 4 x M8-6.8; 2BV707 with 4 x M10-6.8.
  • Electrical connection per national/local regulations and terminal-box circuit diagram; connect protective conductor.
  • Terminal plate tightening torques: M4 = 0.8–1.2 Nm; M5 = 1.8–2.5 Nm.
  • Clearance between bare live parts and to ground at least 5.5 mm at Vn ≤ 690 V.
  • Use motor circuit breakers set to the nominal current on the rating plate.
  • For converter supply use shielded cables with shield installed on both sides.
  • Pipe/hose connections: operating-liquid port G ¼", cavitation protection connection G ¼", drain opening G ¼".
  • Tightening torque for pipe connections on intake and discharge connections must not exceed 100 Nm.
  • Install a start-up screen in the inlet pipe for the first 100 operating hours.
pp. 22-25
Puesta en marcha

Comprobaciones previas al arranque, llenado con líquido de servicio, comprobación del sentido de giro y procedimientos de arranque para el funcionamiento autoaspirante y el funcionamiento con alimentación de líquido de servicio.

  • Unit may only be started with fan guard and vacuum pump/compressor housing mounted, lines attached and tested for strength and leaks.
  • Do not run dry; mechanical seal is destroyed in seconds without operating liquid.
  • Maximum discharge pressure when gases/vapors are passed on is 1.1 bar abs.
  • For self-priming operation, fill with operating liquid during installation; for operation with operating-liquid feed, fill after completing installation.
  • For operation with operating-liquid feed, open the stop valve for approx. 20 seconds to fill the working area.
  • Check direction of rotation by briefly switching on and comparing external fan rotation with arrows on motor mounting adapter and fan guard.
  • Self-priming operation requires a vacuum of at least 900 mbar abs. in the inlet pipe at switch-on and liquid level at shaft center; during operation the reservoir level may not drop below approx. 1 m below shaft center.
  • For operation with operating-liquid feed, set pre-pressure pA approx. 1 bar above inlet pressure pB.
pp. 33
Reparaciones/Localización de averías

Tabla de averías que enumera síntomas, causas, remedios y el personal responsable de cada acción correctiva.

  • Covers motor not starting, protective motor switch tripping, high power consumption, and failure to generate vacuum.
  • Remedies include checking fuses/terminals/cables, freeing a jammed impeller, decalcifying, cleaning, correcting impeller gap, replacing impeller or motor bearings, throttling operating-liquid flow, reducing counter-pressure, sealing leaks and reversing direction of rotation.
  • Work is assigned to Electrician, Operator or Service as appropriate.

Key Integration, Operating & Safety Requirements

Specification / Condition Engineering Implication Aplica a
La temperatura máxima de los gases/vapores bombeados es +80 °C [+176 °F]. p.10 ↗ At higher fluid temperatures, measures must be taken on the system to prevent burns, e.g. mount a separating safety device (cover). whole series
Temperatura del líquido de servicio: máx. +80 °C, mín. +5 °C, nominal +15 °C. p.10 ↗ Operating liquid must be kept within these limits; minimum inlet pressure depends on operating-liquid temperature (Fig. 1). whole series
Temperatura ambiente: máx. +40 °C [+104 °F], mín. +5 °C [+41 °F]. p.10 ↗ Installation location must remain within this ambient range. whole series
Presión máxima de descarga durante el funcionamiento como bomba de vacío: 1,3 bar abs. [18,8 psia]. p.10 ↗ System back-pressure on the discharge side must not exceed this value in vacuum operation. whole series
Presión máxima admisible en el grupo motobomba: 8 bar abs. [116 psia]. p.10 ↗ If higher pressures can occur in the system, corresponding protective devices must be provided. whole series
Presión máxima de descarga durante el funcionamiento como compresor con presión de aspiración p1 = 1 bar abs.: 2BV7060 2,0/2,4 bar abs. (50/60 Hz); 2BV7061 1,9/1,9 bar abs.; 2BV7070 3,0/2,5 bar abs.; 2BV7071 3,5/2,2 bar abs. p.10 ↗ Compressor duty limits are type- and frequency-dependent; select the type accordingly. 2BV7060, 2BV7061, 2BV7070, 2BV7071
Caudal nominal de líquido de servicio con extracción de aire seco y agua a 15 °C: 2BV7060 0,20 m³/h; 2BV7061 0,23 m³/h; 2BV7070 0,28/0,34 m³/h (50/60 Hz); 2BV7071 0,45/0,55 m³/h (50/60 Hz). p.11 ↗ Operating-liquid supply must be set to these nominal flow rates for proper operation. whole series
Cantidad de llenado de líquido de servicio para el cebado: 2BV7060 0,40 l; 2BV7061 0,55 l; 2BV7070 0,80 l; 2BV7071 1,10 l. p.11 ↗ Use these quantities when filling the working space before commissioning. whole series
Distancia mínima desde la rejilla del ventilador hasta la superficie adyacente: 34 mm para 2BV7060/2BV7061; 53 mm para 2BV7070/2BV7071. p.10 ↗ Maintain these clearances to ensure heat dissipation and cooling are not obstructed. 2BV7060, 2BV7061, 2BV7070, 2BV7071
Velocidad de vibración máxima admisible veff = 4,5 mm/s [0,177 in/s]. p.16 ↗ Installation and foundation must ensure total vibration does not exceed this value for proper operation and long service life. whole series
Atornillado de las patas: 2BV706 utiliza 4 x M8-6.8; 2BV707 utiliza 4 x M10-6.8. p.17 ↗ Use suitable securing elements of these sizes to bolt the unit to the supporting surface. 2BV7060/2BV7061 (2BV706); 2BV7070/2BV7071 (2BV707)
Pares de apriete de la placa de bornes: M4 = 0,8–1,2 Nm; M5 = 1,8–2,5 Nm. p.18 ↗ Electrical connections must be tightened to these torques for a permanently safe connection. whole series
Distancia entre partes activas desnudas y entre partes activas desnudas y tierra: al menos 5,5 mm con tensión nominal Vn ≤ 690 V. p.18 ↗ Ensure no protruding wire pieces and maintain this clearance in the terminal box. whole series
Desviaciones de alimentación admisibles sin reducción del rendimiento: ±5 % de tensión, ±2 % de frecuencia. p.18 ↗ Operating conditions must correspond to the motor rating plate within these tolerances. whole series
El par de apriete para las conexiones de tubería en las conexiones de aspiración y descarga no debe superar 100 Nm [73,8 ft lbs]. p.20 ↗ Avoid over-tightening pipe connections to prevent damage. whole series
El funcionamiento autoaspirante requiere un vacío de al menos 900 mbar abs. [13,1 psia] en la tubería de aspiración al conectar, y el nivel de líquido en la tubería de alimentación/depósito debe estar al mismo nivel que el centro del eje de la unidad. p.24 ↗ Pre-throttle on the inlet side and establish correct liquid level before starting in self-priming mode. whole series
Durante el funcionamiento autoaspirante, el nivel de líquido en el depósito no puede descender por debajo de aprox. 1 m [3,28 ft] por debajo del centro del eje de la unidad. p.24 ↗ Reservoir and feed pipe must be arranged to maintain this minimum level during operation. whole series
Para el funcionamiento con alimentación de líquido de servicio, ajustar la contrapresión pA en la tubería de alimentación aprox. 1 bar [14,5 psi] por encima de la presión de aspiración pB. p.25 ↗ Operating-liquid feed pressure must be regulated relative to inlet pressure. whole series
La presión máxima de descarga cuando los gases/vapores bombeados se conducen es 1,1 bar abs. [16,0 psia]. p.22 ↗ Ensure downstream system cannot exceed this pressure during commissioning and operation. whole series
Altura de instalación máxima 1000 m [3280 ft] sobre el nivel del mar. p.16 ↗ Higher altitudes require consultation with service. whole series

Faults & Troubleshooting

Código / Síntoma Possible Cause Remedy Note
Motor does not start, no motor noise. p.33 ↗ At least two power supply leads interrupted. Check fuses, terminals and cables for open circuit. Eliminate open circuit. Carried out by: Electrician
Motor does not start, humming noise.. p.33 ↗ One power supply lead interrupted. Check fuses, terminals and cables for open circuit. Eliminate open circuit. Carried out by: Electrician
Motor does not start, humming noise.. p.33 ↗ Impeller is jammed. Free shaft by turning. See Chapter 11.1, "Maintenance", Pg. 30. Carried out by: Operator
Motor does not start, humming noise.. p.33 ↗ Impeller is jammed. Decalcify vacuum pump/compressor. See Chapter 11.1, "Maintenance", Pg. 30. Carried out by: Operator
Motor does not start, humming noise.. p.33 ↗ Impeller is jammed. Drain and clean vacuum pump/compressor if necessary. See Chapter 11.1, "Maintenance", Pg. 30. Carried out by: Operator
Motor does not start, humming noise.. p.33 ↗ Impeller is jammed. Check and correct impeller gap setting if necessary. Carried out by: Service
Motor does not start, humming noise.. p.33 ↗ Impeller defective. Replace impeller. Carried out by: Service
Motor does not start, humming noise.. p.33 ↗ Motor bearings defective. Replace motor bearings. Carried out by: Service
Protective motor switch trips when motor is switched on. p.33 ↗ Winding short-circuit. Have winding checked. Carried out by: Electrician
Protective motor switch trips when motor is switched on. p.33 ↗ Motor overloaded. Throttle operating-liquid flow rate. See Chapter 8.2, "Self-priming operation", Pg. 24 or 8.3, "Operation with operating-liquid feed", Pg. 25. Carried out by: Operator
Protective motor switch trips when motor is switched on. p.33 ↗ Counter-pressure at discharge connection too high. Reduce counter-pressure. Carried out by: Operator
Protective motor switch trips when motor is switched on. p.33 ↗ Share of liquid also fed too high. Reduce share of liquid also fed. Carried out by: Operator
Protective motor switch trips when motor is switched on. p.33 ↗ Impeller is jammed. See "Motor does not start, humming noise." Carried out by: Service
Power consumption too high. p.33 ↗ Lime or other deposits. Decalcify vacuum pump/compressor. See Chapter 11.1, "Maintenance", Pg. 30. Carried out by: Operator
Power consumption too high. p.33 ↗ Lime or other deposits. Clean vacuum pump/compressor. See Chapter 11.1, "Maintenance", Pg. 30. Carried out by: Operator
Unit does not generate vacuum. p.33 ↗ No operating liquid. Ensure proper operating-liquid flow rate. See Chapter 8.2, "Self-priming operation", Pg. 24 or Chapter 8.3, "Operation with operating-liquid feed", Pg. 25. Carried out by: Operator
Unit does not generate vacuum. p.33 ↗ Severe leak in the system. Seal leak in the system. Carried out by: Operator
Unit does not generate vacuum. p.33 ↗ Wrong direction of rotation. Reverse direction of rotation by interchanging two connecting leads. Carried out by: Electrician