LC-30ADSF Instruction Manual - Solvent Delivery Module
Technical Reference Summary
Covered Models & Document Scope
Este manual cubre el módulo de suministro de disolvente Shimadzu LC-30ADSF (bomba de CO2) para sistemas SFC/SFE. Describe la unidad de bomba estándar, su operación mediante teclado/visualizador, las funciones auxiliares y VP, los programas de tiempo, la operación en gradiente (unidades de bomba maestra/esclava), las E/S externas, la resolución de problemas, el mantenimiento y las especificaciones. Los accesorios opcionales mencionados incluyen la válvula de cierre de CO2 líquido, el kit de enjuague automático (estándar), el regulador de contrapresión SFC-30A, la válvula de conmutación de línea de flujo FCV y la unidad de desgasificación.
Section-by-Section Technical Breakdown
Enumera los componentes estándar y el paquete de accesorios suministrados con el LC-30ADSF, incluidos los números de pieza y las cantidades. También describe la descripción general del instrumento y las características clave, como el enfriamiento integrado del cabezal de la bomba, el suministro de CO2 a alta presión de hasta 66 MPa, la baja pulsación y el enjuague automático del émbolo.
- Instrument: LC-30ADSF pump unit.
- Accessory pack includes optical cable 070-92025-51, clamp 046-05522-02, spiral tube wrap 018-26020-02, pipe clip 037-60177-05, silicone tubing 228-25162-03, elbow tubing 228-44611-91, L-type tubing connector 035-61561-12, washing bottle 228-58181-42, refrigerant bottle 228-58181-41, bottle holder 228-51593, flow review jig 228-61054-41, RS-232C cable 070-03623-02.
- Built-in pump head cooling mechanism for stable CO2 delivery.
- Maximum pressure up to 66 MPa.
- Discharge volume per plunger stroke: 10 µL for low pulsation.
Describe el panel frontal, los conectores del panel posterior, el panel de visualización y el teclado. Explica las funciones de los indicadores del visualizador (flujo, presión, p.max, p.min, bomba, prog.run, remoto, G.E., indicador de estado) y del teclado de 24 teclas.
- Rear connectors: external I/O terminals, CO2 injection connector, PUMP PRESS (0–5 to 0–100 MPa in 20 steps), DGU PRESS, SFC, REMOTE, OPTION, power cord.
- Status indicator: green = power ON, red = error, orange = sleep mode.
- Pump indicator illuminates when pump runs; blinks when pump stops and liquid CO2 shutoff valve is open.
- G.E. indicator blinks in Fast LC mode.
- Keypad includes pump, run, valve, VP, sleep, delete, edit, clear, back, concentration, function, enter, numeric keys.
Cubre el encendido/apagado, la verificación del cero del sensor de presión antes de la operación y el enfriamiento del cabezal de la bomba. La lectura de presión debe estar dentro de -0.3 a 0.3 MPa sin conexiones de tubería; de lo contrario, utilice ZERO ADJ.
- Power ON: press power switch in; OFF: press again.
- Before operation, remove all plumbing from pressure sensor and verify pressure display is -0.3 to 0.3 MPa.
- If pressure is outside range, perform zero adjustment with [ZERO ADJ].
- Pump head cooling requires connecting the RS-232C cable provided with LC-30ADSF to SFC-30A.
Explica cómo ajustar el caudal, el límite máximo de presión (p.max) y el límite mínimo de presión (p.min). Enumera los rangos de parámetros, los pasos y los valores iniciales, y describe la parada automática de la bomba y las alarmas cuando se superan los límites.
- Flow rate range: 0 to 5.0000 mL/min, step 0.0001 mL/min, initial 0 mL/min.
- p.max range: 1.0–66.0 MPa for flow 0–3.0000 mL/min; 1.0–44.0 MPa for flow 3.0001–5.0000 mL/min; step 0.1 MPa; initial 10 MPa.
- p.min range: 0.0–66.0 MPa for flow 0–3.0000 mL/min; 0.0–44.0 MPa for flow 3.0001–5.0000 mL/min; step 0.1 MPa; initial 0 MPa.
- If pressure exceeds p.max, pumping stops and ERROR P-MAX alarm appears.
- If pressure remains below p.min for more than 3 minutes, pumping stops and ERROR P-MIN alarm appears.
- Setting p.min to 0 disables automatic stop on pressure drop.
Describe la operación en gradiente de alta presión utilizando dos unidades de bomba (bomba A maestra, bomba B esclava). Cubre los ajustes preparatorios (SYS, ADRS), el ajuste del flujo y la concentración iniciales, y las notas de operación.
- Two control methods: all pumps via system controller (Fast LC or Normal mode), or pump A controls pump B (Normal mode).
- Set SYS parameter: pump A = 2, pump B = 1.
- Set ADRS link address for both pumps (e.g., 85).
- Set p.max and p.min individually for each pump; limits apply only to that pump.
- Mobile phase B concentration range 0–100%, minimum setting unit 0.1%.
- Do not press RUN on pump B during gradient operation controlled by pump A.
Proporciona el procedimiento para operar el kit de enjuague automático, incluido el ajuste del caudal, el arranque de la bomba, la verificación del flujo de solución de enjuague y las indicaciones de mantenimiento.
- Set flow rate to about 3 mL/min.
- Press PUMP to start; pump indicator illuminates.
- Check liquid flow from PTFE tubing at rinsing kit outlet.
- Replace rinse solution with 10% 2-propanol solution once a day as a rough guide.
- If air bubbles are released from the pump, CO2 may be leaking from a plunger seal; remove rinsing kit and drain rinse solution.
Enumera y describe los parámetros de funciones auxiliares agrupados en Ajustes de parámetros, Operación de archivos, Ajustes de control, Ajustes del sistema y Ajustes de monitorización. Incluye ajustes como salida EVENT, compensación de compresibilidad, P-SET, ZERO ADJ, MODE CHANG, LOCAL, ADRS, KEY CLOSE, BRIGHT, EXT-S, SYS, S-PROT, PRS-UNIT, RANGE, BEEP MODE y funciones de monitorización.
- Parameter Settings Group: EVENT, COMP.
- File Operation Group: FILE NUM, FILE CPY, FILE DEL.
- Control Settings Group: P-SET, ZERO ADJ, MODE CHANG.
- System Settings Group: LOCAL, ADRS, KEY CLOSE, BRIGHT, EXT-S, SYS, S-PROT, PRS-UNIT, RANGE, BEEP MODE.
- Monitor Settings Group: MON TIME, MON FLOW, MON ID, MON REV, CONDITION, DEGAS PRS.
Describe las funciones VP (validación/producto), incluida la monitorización de la fase móvil, la información del producto, la información de mantenimiento, el soporte de validación y el soporte de calibración. Cubre el número de serie, la versión de software, el tiempo total de operación, los volúmenes entregados por los sellos, el registro de mantenimiento, el registro de errores, el registro de operaciones, la fecha/hora, la verificación de memoria, la verificación de pulsos, la verificación de flujo, el programa de prueba de gradiente y la prueba de fuga de CO2.
- Mobile Phase Monitor Group: MOBILE PHASE, ALARM LEVEL.
- Product Information Group: SERIAL NUMBER, S/W ID.
- Maintenance Information Group: TOTAL OP TIME, L SEAL DELIVERED, R SEAL DELIVERED, DGU OP TIME, PART REPLACEMENT, MAINTENANCE LOG, ERROR LOG, OPERATION LOG.
- Validation Support Group: DATE, TIME, MEMORY CHECK, PULSE CHECK, FLOW CHECK, GE TEST PROGRAM, LEAKAGE TEST.
- Calibration Support Group: Input PASSWORD, FLOW COMP FACT, PRESS COMP FACT, SEAL REPLACEMENT, FAST LC MODE, INITIALIZE PARAM, CHANGE PASSWORD, CBM PARAMETER.
Explica cómo crear, editar, eliminar, iniciar y detener programas de tiempo, incluidos los programas de gradiente y los comandos especiales STOP, LOOP y GOTO.
- Time program commands include flow, pressure, concentration, EVENT, etc.
- Gradient programs can be created using BCNC command.
- STOP command sets stop of time program.
- LOOP command sets loop count.
- GOTO command switches file.
- RUN key starts/stops time program; inoperative if no program registered.
Cubre la preparación para la conexión a un controlador del sistema y la conexión de terminales de entrada/salida externos y cable de eventos.
- Connect to system controller via REMOTE connector.
- External I/O terminals allow event signal input/output.
- Event cable connection described in section 5.6.2.
Proporciona tablas de síntomas, causas probables y acciones correctivas para problemas comunes como fallo de alimentación, ausencia de bombeo, bombeo inestable, fugas, problemas de presión y diferencias de presión en gradiente. También incluye una tabla de mensajes de error con tipos de alarma, causas y acciones.
- Symptoms covered: power does not turn ON, key operation not possible, no liquid pumped, unstable pumping, leaks, flow rate below set value, retention time not reproducible, pressure does not rise, pressure rises too much, air bubbles in rinse solution, rinse solution volume decreases.
- Error messages: ERROR P-MAX, ERROR P-MIN, ERROR HOME POS, ERROR EXTERNAL, WARN M-PHASE.
- Corrective actions include cleaning/replacing check valves, replacing plunger seals, retightening male nuts, cleaning line filter, zero adjustment of pressure sensors, replacing CO2 cylinder if remaining <10 kg.
Describe la inspección y el mantenimiento periódicos, la sustitución del sello del émbolo, la limpieza e inspección de los émbolos y diafragmas, la inspección y limpieza ultrasónica de las válvulas de retención, la inspección/sustitución del filtro de línea, la limpieza exterior y la limpieza del kit de enjuague automático.
- Periodic inspection list and check after maintenance.
- Plunger seal replacement procedure including pump head removal and installation.
- Cleaning/inspection of plungers and diaphragms.
- Check valve inspection, ultrasonic bath cleaning, or replacement.
- Line filter inspection/replacement.
- Exterior cleaning and automatic rinsing kit cleaning.
Proporciona las especificaciones técnicas de la unidad de bomba LC-30ADSF y del sistema de gradiente, incluidos la presión, el caudal y los métodos de control.
- Maximum pressure: 66 MPa (for flow up to 3.0000 mL/min); 44 MPa (for flow 3.0001–5.0000 mL/min).
- Flow rate range: 0 to 5.0000 mL/min.
- Gradient system can be controlled by system controller or by pump unit.
- Maintenance parts and consumable parts listed.
Key Integration, Operating & Safety Requirements
| Specification / Condition | Engineering Implication | Aplica a |
|---|---|---|
| El rango del límite máximo de presión p.max es 1.0–66.0 MPa para caudales de 0–3.0000 mL/min y 1.0–44.0 MPa para caudales de 3.0001–5.0000 mL/min. p.20 ↗ | When selecting operating pressure, ensure it does not exceed the limit corresponding to the set flow rate; higher flow rates reduce the allowable maximum pressure. | LC-30ADSF |
| El rango del límite mínimo de presión p.min es 0.0–66.0 MPa para caudales de 0–3.0000 mL/min y 0.0–44.0 MPa para caudales de 3.0001–5.0000 mL/min; el ajuste 0 desactiva la parada automática por caída de presión. p.23 ↗ | Set p.min to protect against leaks or CO2 depletion; setting 0 removes protection. | LC-30ADSF |
| Si la presión permanece por debajo de p.min durante más de 3 minutos, el bombeo se detiene automáticamente y se produce la alarma ERROR P-MIN. p.23 ↗ | The 3-minute delay prevents nuisance trips from short pressure fluctuations; ensure p.min is set appropriately. | LC-30ADSF |
| Antes de la operación, sin conexiones de tubería al sensor de presión, la visualización de presión debe leer entre -0.3 y 0.3 MPa. p.18 ↗ | If outside this range, perform zero adjustment using [ZERO ADJ] to ensure accurate pressure readings. | LC-30ADSF |
| El conector PUMP PRESS emite voltaje para la monitorización externa de presión, ajustable de 0–5 MPa hasta 0–100 MPa en 20 pasos. p.13 ↗ | Select the appropriate range for the external device to match expected pressure levels. | LC-30ADSF |
| En modo gradiente, las dos unidades de bomba pueden mostrar diferencias de presión de hasta 2.0 MPa o 5% como normal. p.71 ↗ | Do not attempt to correct small pressure differences; only investigate if exceeding this tolerance. | Gradient system with two LC-30ADSF units |
| Para la operación en gradiente controlada por la bomba A, ajuste el parámetro SYS a 2 en la bomba A y a 1 en la bomba B; ajuste la dirección de enlace ADRS en ambas. p.25 ↗ | Correct master/slave configuration is required for proper gradient control. | Gradient system with two LC-30ADSF units |
| La concentración de fase móvil B se puede ajustar de 0 a 100% con una unidad mínima de ajuste de 0.1%. p.26 ↗ | Gradient precision is 0.1%; mobile phase A concentration is automatically 100% minus B concentration. | LC-30ADSF in gradient mode |
| Sustituya la solución de enjuague del kit de enjuague automático por solución de 2-propanol al 10% una vez al día como guía aproximada. p.28 ↗ | Regular replacement maintains rinsing effectiveness and extends plunger seal life. | LC-30ADSF with automatic rinsing kit |
| Si la cantidad restante de CO2 en el cilindro es inferior a 10 kg, sustituya el cilindro por uno nuevo. p.71 ↗ | Low CO2 can cause pressure fluctuations and unstable pumping; monitor cylinder weight. | LC-30ADSF |
| El volumen de descarga por carrera del émbolo es de 10 µL, y el accionamiento de alta velocidad reduce la pulsación de flujo y el período de pulsación. p.9 ↗ | Provides precise delivery suitable for high-resolution separations. | LC-30ADSF |
| La presión máxima admisible del instrumento es de 66 MPa; al conectar con otros equipos, ajuste el límite máximo de presión de acuerdo con el límite de presión de todos los componentes del sistema. p.22 ↗ | Do not exceed the lowest pressure rating among all connected components. | LC-30ADSF |
| El enfriamiento del cabezal de la bomba requiere la conexión del cable RS-232C suministrado al regulador de contrapresión SFC-30A. p.19 ↗ | Ensure this cable is connected for proper temperature control of the pump head. | LC-30ADSF |
| El indicador de estado muestra verde cuando la alimentación está encendida, rojo cuando se genera un error y naranja durante el modo de reposo. p.14 ↗ | Use the indicator color for quick status diagnosis. | LC-30ADSF |
| El indicador de la bomba parpadea cuando la bomba se detiene y la válvula de cierre de CO2 líquido está abierta (válvula opcional). p.14 ↗ | A blinking pump indicator with pump stopped indicates the shutoff valve is open; close it if not needed. | LC-30ADSF with optional liquid CO2 shutoff valve |
| El indicador G.E. parpadea cuando el modo de análisis está ajustado al modo Fast LC. p.14 ↗ | Indicates Fast LC mode is active; ensure method compatibility. | LC-30ADSF |
| El rango de caudal es de 0 a 5.0000 mL/min con un paso de 0.0001 mL/min. p.20 ↗ | Very fine flow adjustments are possible; ensure flow rate is not set to 0 when pumping is desired. | LC-30ADSF |
| El rango de ajuste de cero del sensor de presión es de -0.3 a 0.3 MPa; si está fuera de este rango, utilice ZERO ADJ. p.18 ↗ | Regular zero checks ensure accurate pressure control and limit protection. | LC-30ADSF |
Faults & Troubleshooting
| Código / Síntoma | Possible Cause | Remedy | Note |
|---|---|---|---|
| Power does not turn ON even after switching ON power. p.78 ↗ | Power plug is disconnected. | Connect plug correctly. | P. 2 |
| Power does not turn ON even after switching ON power. p.78 ↗ | Power cord internal wires are cut. | Replace with a new cord of the same type. | P. 2 |
| Power does not turn ON even after switching ON power. p.78 ↗ | Power supply does not meet specifications for this instrument. | Use power supply that meets specifications for this instrument. | |
| Key operation is not possible. p.78 ↗ | DISPLAY was not pressed. | Press DISPLAY. | Operation keys are shown to operate. P. 7 |
| No liquid is pumped. (The instrument does not run.) p.78 ↗ | PUMP was not pressed. (Pump indicator does not illuminate.) | Press PUMP. The pump indicator will illuminate. | P. 16 |
| No liquid is pumped. (The instrument does not run.) p.78 ↗ | System controller did not send start signal. | Have the system controller send a signal to start pumping. | *1 |
| No liquid is pumped. (The instrument does not run.) p.78 ↗ | Flow rate is set to [0]. | Set a flow rate other than 0. | P. 13 |
| No liquid is pumped. (The instrument does not run.) p.78 ↗ | System controller set flow rate to 0. | Have the system controller set a flow rate. | *1 |
| No liquid is pumped. (The instrument does not run.) p.78 ↗ | Pump head cooling has stopped or cooling is instable. | Press PUMP of SFC-30A to start cooling. Check that the refrigerant bottle is filled with 30% ethylene glycol. | |
| No liquid is pumped. (The instrument does not run.) p.78 ↗ | Error message (P.MAX, P.MIN etc.) appears. | Press CLEAR to clear the message and take corrective actions for errors. | P. 73 |
| The instrument is running, but no liquid is pumped. p.78 ↗ | Check valve is not working properly. | Push in 2-propanol etc. from the inlet check valve. *2 | *2: Connect the provided syringe tubing to the inlet check valve and push in 2-propanol etc. |
| Pumping is unstable, with large pump pulsation. p.79 ↗ | Check valve is fouled. | Push in 2-propanol etc. from the inlet check valve. *2; Pump 2-propanol to clean check valve. If cleaning check valve is not effective, clean the valve in an ultrasonic bath or replace it. | P. 94 |
| Pumping is unstable, with large pump pulsation. p.79 ↗ | Liquid is leaking from gap between pump head and head holder, or from rinse flow lines. | Replace the plunger seal. If carbon dioxide is still leaking after replacing the plunger seal, replace the plunger. | P. 80, P. 88 |
| Pumping is unstable, with large pump pulsation. p.79 ↗ | Mobile phase is leaking from a flow line connection. | Retighten the male nuts. If retightening the male nuts is not effective, replace the tubing, male nuts and ferrules. | |
| Pumping is unstable, with large pump pulsation. p.79 ↗ | Flow line is (partially) clogged. | Clean the line filter in an ultrasonic bath or replace it. Identify the clogged parts and replace it. | P. 96 |
| Pumping is unstable, with large pump pulsation. p.79 ↗ | Little CO2 remains in the cylinder. | Measure the remaining quantity (weight) of CO2 in the cylinder and, if the remaining quantity is less than 10 kg, replace the cylinder with a new CO2 cylinder. | |
| Flow rate is below set value. p.79 ↗ | Check valve does not work properly. | Pump 2-propanol to clean check valve. Otherwise, clean the valve in an ultrasonic bath or replace it. | P. 94 |
| Retention time cannot be reproduced. p.79 ↗ | Check valve does not work properly. | Pump 2-propanol to clean check valve. If cleaning check valve is not effective, replace the valve or clean it in an ultrasonic bath. | P. 94 |
| In a gradient system, the two pump units show different pressures. (Difference of up to 2.0 MPa or 5% is normal.) p.79 ↗ | Zero points of the pressure sensors of two pump units are not the same. | Use ZERO ADJ auxiliary function to execute zero adjustment of the pressure sensors. | P. 30 |
| In a gradient system, the two pump units show different pressures. (Difference of up to 2.0 MPa or 5% is normal.) p.79 ↗ | Line filter of one of the pump units is clogged. | Clean the line filter in an ultrasonic bath, or replace it. | P. 96 |
| In a gradient system, the two pump units show different pressures. (Difference of up to 2.0 MPa or 5% is normal.) p.79 ↗ | Flow line(s) is/are clogged at the junction of the two pump unit flow lines. | Identify the clogged lines and replace it. | |
| Pressure does not rise. p.79 ↗ | Liquid is leaking from flow line connections. | Retighten the male nuts. If retightening the male nuts is not effective, replace the tubing, male nuts and ferrules. | |
| Pressure rises too much. (Remove the column to check.) p.80 ↗ | Line filter is clogged. | Clean the line filter in an ultrasonic bath or replace it. | P. 96 |
| Pressure rises too much. (Remove the column to check.) p.80 ↗ | Flow lines are clogged. | Identify the clogged parts and replace them. | |
| Pressure rises too much. (Remove the column to check.) p.80 ↗ | Inner diameter of tubing is too small. | Use tubing with the appropriate inner diameter. | |
| Air bubbles leaked from the pump are mixed into the rinse solution in the automatic rinsing kit. p.80 ↗ | Liquid is leaking from the plunger seal. | Replace the plunger seal. If carbon dioxide is still leaking after replacing the plunger seal, replace the plunger. | P. 88, P. 80 |
| The volume of the automatic rinsing kit's rinse solution decreases. p.80 ↗ | Rinse solution is leaking from the back of the head holder. | Inspect (or replace) the diaphragm. | |
| ERROR P-MAX p.82 ↗ | Pump discharge pressure has exceeded the set maximum pressure limit, [P.MAX] or the working pumping pressure. Pumping will automatically stop, unless [S-PROT] function has been activated, in which case pumping will continue at half flow rate. | Inspect for clogging in the flow line. If no clogging is found, set the appropriate [P.MAX] value or decrease the flow rate. | "4.1 Setting Parameters" P. 12, "Setting System Protection [S-PROT]" P. 33, "4.1.3 Setting Maximum Pressure Limit" P. 14 |
| ERROR P-MIN p.82 ↗ | Pump discharge pressure has fallen below the set min. pressure limit, [P.MIN]. Pumping will automatically stop. | Inspect for leakage in the flow line. If no leakage is found, set the appropriate [P.MIN] value. Note that [P.MIN] function is not activated for first one minute of pumping. | "4.1.4 Setting Minimum Pressure Limit" P. 15 |
| ERROR HOME POS p.82 ↗ | The motor home position cannot be detected, the motor does not run, or the motor is slipping. | Turn the power OFF and ON again, and press PUMP. If this message still appears, turn the power OFF and contact your Shimadzu representative. | |
| ERROR EXTERNAL p.82 ↗ | An error signal was sent from the external device connected to the external input/output terminal [ERR IN]. | Inspect the external device, and eliminate the cause of the error. | |
| WARN M-PHASE p.82 ↗ | The remaining volume of mobile phase is less than the alarm level. | Replace the mobile phase and reset the amount of mobile phase. | "Showing/Setting Mobile Phase Volume [MOBILE PHASE]" P. 42 |