Induztr
Resumen técnico Visor de documentos Modelos relacionados

Instruction Manual - Nexis GC-2030

Technical Reference Summary

Covered Models & Document Scope

Este documento es el Manual de Instrucciones del cromatógrafo de gases Shimadzu Nexis™ GC-2030. Cubre procedimientos de resolución de problemas y mantenimiento para el sistema GC-2030, incluidos puertos de inyección (SPL, PTV, OCI), detectores (FID, TCD, PTCD, FTD, FPD), controladores de flujo (AFC, APC) y componentes relacionados. No se enumeran variantes de modelo específicas ni códigos de pedido en las páginas proporcionadas.

Section-by-Section Technical Breakdown

pp. 55-60
Resolución de problemas de ajustes de gas y presión

Esta sección aborda problemas en los que la presión o el caudal no se pueden ajustar o no alcanzan el valor establecido, y en los que las fugas de gas no se pueden detener. Proporciona causas y soluciones, incluidos rangos de presión de suministro, procedimientos de comprobación de fugas para columnas capilares y empaquetadas, y acciones correctivas para piezas con fugas.

  • Supply pressure ranges: carrier gas (other than hydrogen) 300–980 kPa; carrier gas (hydrogen) 150–500 kPa; detector gas 300–980 kPa; hydrogen 150–300 kPa; air 300–500 kPa.
  • Carrier gas leak check for capillary columns: set inlet pressure to 150 kPa, total flow 100 mL/min, wait 10 minutes, and compare pressure drop against leak judgment table.
  • Leak judgment: pressure drop >2.5 kPa (below 150 kPa), >5.0 kPa (150–450 kPa), >7.5 kPa (450–600 kPa), >10.0 kPa (600–750 kPa), >12.5 kPa (above 750 kPa).
  • Leak check points: septum, around injection port, tubing connections, split vent, purge vent, column connection.
  • Corrective actions: replace septum, replace O-ring of glass insert, replace seal of blank nut, replace blank nut, replace ferrule/column nut/ClickTek connector.
  • Do NOT use leak detecting fluid or soapy water on connections above the carrier and detector gas controllers (AFC/APC).
  • The instrument allows 0.2 mL/min leakage from split/purge vent.
pp. 61
Resolución de problemas de control de temperatura

Esta sección cubre el problema de que la temperatura no aumenta o no alcanza el valor establecido. Enumera causas como que el GC no se ha iniciado, tiempo de inicio prolongado, pérdida de calor, ajuste de temperatura máxima bajo, temperatura del detector inferior a la temperatura de la columna y programas INJ/horno no coincidentes, junto con soluciones.

  • Press [Start GC] on the [GC Start Sequence] screen to start the GC.
  • Set start time at a lower value if heating has not started.
  • Close the oven door and close the hole of the insulation to prevent heat loss.
  • Increase the maximum temperature setting for the column and other units; set [Max Usable Temp] on the [Column Information] screen correctly.
  • Set the detector temperature larger than the column temperature.
  • Set the total time of the INJ program to match the total time of the oven program.
pp. 61-62
Resolución de problemas del detector (común)

Esta sección proporciona resolución de problemas para problemas comunes del detector: ausencia de picos o picos extremadamente pequeños, ruido de línea base alto, deriva de línea base o fluctuación a largo plazo, y error de ajuste de cero. Se enumeran causas y soluciones para todos los detectores.

  • Check signal cable connections of detector and data processing unit.
  • Turn [On] the detector control.
  • Check for gas leaks at detector-column connection and tighten.
  • Install column correctly with correct insertion length on detector side.
  • Set detector attenuation, range, and current at appropriate values.
  • Perform Auto Zero if zero level is far below '0'.
  • Increase injection volume (normally less than 2 µL for liquid samples and less than 1 mL for gas samples) or increase sample concentration.
  • Reduce split ratio for split analysis.
  • Check syringe for clogging or leaks; replace if necessary.
  • Replace glass insert with deactivated type or acid/alkaline treated one depending on component.
  • Set detector gas flow and filter time constant at proper (recommended) values.
  • Change analytical conditions such as temperature or column flow if incorrect.

Key Integration, Operating & Safety Requirements

Specification / Condition Engineering Implication Aplica a
Presión de suministro de gas portador (distinto de hidrógeno): 300 a 980 kPa. p.55 ↗ Ensure supply pressure is within this range to allow proper pressure/flow control. GC-2030 series
Presión de suministro de gas portador (hidrógeno): 150 a 500 kPa. p.55 ↗ Use this range when hydrogen is used as carrier gas. GC-2030 series
Presión de suministro de gas del detector: 300 a 980 kPa. p.55 ↗ Ensure detector gas supply is within this range. GC-2030 series
Presión de suministro de hidrógeno para el detector: 150 a 300 kPa. p.55 ↗ Use this range for hydrogen detector gas. GC-2030 series
Presión de suministro de aire: 300 a 500 kPa. p.55 ↗ Ensure air supply is within this range. GC-2030 series
Comprobación de fugas de gas portador para columnas capilares: ajuste la presión de entrada a 150 kPa, el flujo total a 100 mL/min, espere 10 minutos y compare la caída de presión con la tabla de juicio de fugas. p.57 ↗ Use this procedure to verify system leak-tightness. GC-2030 with capillary column
Juicio de fuga: si la presión de entrada inicial es inferior a 150 kPa, una disminución superior a 2.5 kPa indica una fuga. p.58 ↗ Use this threshold to determine if a leak exists. GC-2030 series
Juicio de fuga: si la presión de entrada inicial es de 150 a 450 kPa, una disminución superior a 5.0 kPa indica una fuga. p.58 ↗ Use this threshold to determine if a leak exists. GC-2030 series
Juicio de fuga: si la presión de entrada inicial es de 450 a 600 kPa, una disminución superior a 7.5 kPa indica una fuga. p.58 ↗ Use this threshold to determine if a leak exists. GC-2030 series
Juicio de fuga: si la presión de entrada inicial es de 600 a 750 kPa, una disminución superior a 10.0 kPa indica una fuga. p.58 ↗ Use this threshold to determine if a leak exists. GC-2030 series
Juicio de fuga: si la presión de entrada inicial es superior a 750 kPa, una disminución superior a 12.5 kPa indica una fuga. p.58 ↗ Use this threshold to determine if a leak exists. GC-2030 series
El instrumento permite una fuga de 0.2 mL/min por el venteo de split/purge. p.60 ↗ This is an acceptable leak rate; higher leakage may require maintenance. GC-2030 series
NO utilice líquido detector de fugas ni agua jabonosa en las conexiones situadas por encima de los controladores de gas portador y del detector (AFC/APC). p.60 ↗ Drips may damage the controller; use a leak detector instead. GC-2030 series
Normalmente, el volumen de inyección debe ser inferior a 2 µL para muestras líquidas e inferior a 1 mL para muestras gaseosas. p.62 ↗ Exceeding these volumes may contaminate the injection port. GC-2030 series
Para la comprobación de fugas, utilice una tuerca ciega (P/N tipo G: 221-35566-92) y una junta de columna (P/N: 201-35184) en el venteo de purga; para SPL o PTV, instale también una tuerca ciega en el venteo de split. p.57 ↗ These parts are required to seal vents during leak testing. GC-2030 with SPL/PTV

Faults & Troubleshooting

Código / Síntoma Possible Cause Remedy Note
No gas is supplied. p.85 ↗ No gas is supplied. Open the gas cylinder main valve to supply gas. Turn [On] the detector/injection port control. Turn [On] the detector gas control. See also 7.5 Injection Port (P.196), 7.4 Detector (P.139), 7.4.9 Settings for Detector Gas Program (P.175)
Supply pressure is low. p.85 ↗ Supply pressure is low. Change the supply pressure of the gas. Carrier gas (other than hydrogen): 300 to 980 kPa; Carrier gas (Hydrogen): 150 to 500 kPa; Detector gas: 300 to 980 kPa; Hydrogen: 150 to 300 kPa; Air: 300 to 500 kPa. See also 8.3.2 Gas Supply Pressure (P.348)
Gas leaks. p.85 ↗ Gas leaks. Check for gas leaks, and tighten leaking connections. Replace the gasket or septum. Additionally tighten the graphite ferrule. If there is leakage even after additional tightening, replace it. See also Carrier gas leak check (Capillary) (P.57)
Set value is incorrect. p.86 ↗ Set value is incorrect. Set pressure at a proper value. See also 8.6 AFC, APC (P.372)
Set value is outside controllable range. p.86 ↗ Carrier gas type or column information is incorrect. Set the carrier gas type or column information correctly. See also 7.5 Injection Port (P.196), 7.6.2 [Column Information] Screen (P.241)
Total flow is too low, and pressure cannot increase. p.86 ↗ Total flow is too low, and pressure cannot increase. Increase the total flow. See also 8.6 AFC, APC (P.372)
Split ratio is set at a low value and total flow is low. p.86 ↗ Split ratio is set at a low value and total flow is low. Increase split ratio to increase the total flow.
Split line filter is clogged. p.86 ↗ Split line filter is clogged. Replace the filter of the split line. See Maintenance Help
Even if total flow is increased, the actual flow of the split vent is low and the pressure is high. p.86 ↗ Split line filter is clogged. Replace the filter of the split line. See Maintenance Help
Part is incorrectly installed. p.86 ↗ Part is incorrectly installed. Install parts correctly.
Graphite ferrule or other seal such as O-ring is damaged. p.86 ↗ Graphite ferrule or other seal such as O-ring is damaged. Replace O-ring. Additionally tighten the graphite ferrule. If there is leakage even after additional tightening, replace it. See Maintenance Help
Tubing including pipes and joints is damaged. p.86 ↗ Tubing including pipes and joints is damaged. Replacement of the tubing part is required. Turn off the main power of the instrument, shut off gas supplies, and contact your Shimadzu sales/service representative.
GC has not started yet. p.91 ↗ GC has not started yet. Press [Start GC] on the [GC Start Sequence] screen to start the GC. See also 7.1.1 [GC Start Sequence] Screen (P.98)
Because start time is too long, heating has not started yet. p.91 ↗ Because start time is too long, heating has not started yet. Set the start time at a lower value. Immediately after this setup value is changed, the new value is in effect. See also 7.1.1 [GC Start Sequence] Screen (P.98)
Heat loss is large. p.91 ↗ Heat loss is large. Close the oven door. Close the hole of the insulation.
Because maximum temperature is set at a very low value, an overheat error occurs. p.91 ↗ Because maximum temperature is set at a very low value, an overheat error occurs. Increase the maximum temperature setting for the column and other units. Set [Max Usable Temp] on the [Column Information] screen correctly. See also [Max Temperature] Screen (P.284), 7.6.2 [Column Information] Screen (P.241)
Detector temperature is lower than the set value of column temperature. p.91 ↗ Detector temperature is lower than the set value of column temperature. Set the detector temperature larger than the column temperature. See also 7.4 Detector (P.139)
The INJ program does not match the oven program. p.91 ↗ The INJ program does not match the oven program. Set the total time of the INJ program to match the total time of the oven program. See also 7.5.4 [INJ/FLOW] Screen (OCI) (P.208), 7.5.5 [INJ/FLOW] Screen (PTV) (P.212)
Signal cable of the detector is connected incorrectly. p.91 ↗ Signal cable of the detector is connected incorrectly. Connect the signal cable correctly. See Maintenance Help
Detector control is turned [Off]. p.91 ↗ Detector control is turned [Off]. Turn [On] the detector control. See also 7.4 Detector (P.139)
Signal cable of the data processing unit is connected incorrectly. p.91 ↗ Signal cable of the data processing unit is connected incorrectly. Connect the signal cable correctly. See also 8.9 Connecting to External Devices (P.404)
There is a leak at the connection of the detector with the column. p.91 ↗ There is a leak at the connection of the detector with the column. Check for gas leaks, and tighten leaking connections. See also Carrier gas leak check (Capillary) (P.57)
The length of the inserted column on the detector side is incorrect. p.91 ↗ The length of the inserted column on the detector side is incorrect. Install the column correctly. See Maintenance Help
Detector attenuation, range, or current is not appropriate. p.92 ↗ Detector attenuation, range, or current is not appropriate. Set the detector attenuation, range, and current at appropriate values. See also 7.4 Detector (P.139)
Zero level is far below "0". p.92 ↗ Zero level is far below "0". Check the signal level on the Monitor screen and perform Auto Zero. See also 7.2 Monitor (P.111)
Injection volume is too low. Or sample concentration is low. p.92 ↗ Injection volume is too low. Or sample concentration is low. Increase the injection volume. (Normally, less than 2 μL for liquid samples and less than 1 mL for gas samples.) Large injection volume may contaminate the injection port. Increase the sample concentration.
Split ratio is too high. (For split analysis) p.92 ↗ Split ratio is too high. (For split analysis) Reduce the split ratio. See also 7.5.1 [INJ/FLOW] Screen (SPL) (P.196), 7.5.5 [INJ/FLOW] Screen (PTV) (P.212)
Sample is injected incorrectly. p.92 ↗ Sample is injected incorrectly. Check the clogging or leaks of the syringe and repair it. Replace the syringe. See Maintenance Help
Component is adsorbed in the glass insert. p.92 ↗ Component is adsorbed in the glass insert. Replace the glass insert with deactivated type. Replace the glass insert with acid or alkaline treated one depending on the component. See Maintenance Help
Detector gas flow is incorrect. p.92 ↗ Detector gas flow is incorrect. Set it at a proper (recommended) value. See Maintenance Help
Detector filter time constant is incorrect. p.92 ↗ Detector filter time constant is incorrect. Set it at a proper (recommended) value. See also 7.4.10 [Signal Settings] Screen (P.177)
Analytical conditions, such as temperature or column flow are incorrect. p.92 ↗ Analytical conditions, such as temperature or column flow are incorrect. Change the analytical conditions.

Modelos relacionados