Induztr
Resumen técnico Visor de documentos Modelos relacionados

CS 200-H Immersion Circulator Datasheet

Contenido

  1. Overview p. 1
    Product introduction and main features of CS 200-H
  2. Spec p. 2
    Technical data according to DIN 12876
  3. p. 1 table, 32 rows

Technical data according to DIN 12876

CharacteristicValue
Operating temperature range-20...85 °C
temperature set point / displaycolour LED Touchscreen
Internal temperature sensorPt100
Temperature stability at -10°C0,5 K
Interface digitalRS232
Safety classificationI / NFL
Heating power6 kW
Cooling power at ambient temperature 20°C.
at 15°C28 kW
at 10°C20 kW
at 0°C18 kW
at -10°C15 kW
at -20°C9,5 kW
Refrigeration machineair-cooled, CFC- and HCFC-free
Refrigerant (ASHRAE, GHS)R-449A (A1, H280)
Refrigerant quantity12 kg
CO2 equivalent16,76 t
Circulation pump: max. delivery105 l/min
max. delivery pressure4,7 bar
Pump connectionG1 male
min. filling capacity225 l
max. filling capacity245 l
Overall dimensions WxDxH **1400x1000x1800 mm
Net weight515 kg
sound pressure level +/- 4 dB(A)78 dB(A)
Power supply (3 Phase)400V 3~ 50Hz
max. current (3 Phase)23 A
Fuse (3 phase)3x32A
Degree of ProtectionIP52
min. ambient temperature5 °C
max. ambient temperature32 °C
from Serial-No.:1.0/24

** Technical details and dimensions are subject to change. No liability is accepted for errors or omissions. Illustrations can deviate from the original.

Engineering Facts

14 facts · every claim linked to a page
Installation

The chiller requires a three-phase 400 V supply with a 3x32 A fuse, so the site electrical infrastructure must be sized accordingly.

Determines the electrical connection, cable sizing and protection device needed at the installation site.

Source
“Power supply (3 Phase) 400V 3~ 50Hz”
Installation

Three-phase devices drawing less than 63 A are delivered with a cable but without a plug, so the customer must provide and fit the plug.

Affects installation planning and the bill of materials for the electrical hook-up.

Source
“Three-phase devices with current consumption less than 63A --> with cable, without plug”
Installation

The unit must be operated within an ambient temperature window of 5 to 32 °C, which constrains where it can be installed.

Room conditions at the installation site must be verified to stay within the allowed ambient range.

Source
“min. ambient temperature 5 °C”
Performance

Cooling capacity is rated at 20 °C room temperature and drops if ambient temperature rises, so capacity must be derated for warmer rooms.

Prevents undersizing the chiller when the actual installation room is warmer than 20 °C.

Source
“Output data valid for: Room temperature 20°C. If the ambient temperature rises, the cooling capacity may drop.”
Installation

Voltage and frequency tolerances are coupled: ±5 % voltage is only allowed with ±2 % frequency, and certain combinations are explicitly forbidden.

The site power quality must be checked against EN60034-1 tolerances before commissioning.

Source
“-5% voltage and +2% frequency -> not allowed!”
Safety

The refrigerant R-449A is classified A1 but carries GHS hazard H280 (pressurised gas), and the unit contains 12 kg with a CO2 equivalent of 16.76 t.

Relevant for refrigerant handling, leak reporting obligations and safety labelling at the site.

Source
“R-449A (A1, H280)”
Operation

The recommended heat transfer fluid is a 50:50 water–monoethylene glycol mixture.

Guides fluid selection to avoid freezing, corrosion or performance issues.

Source
“Recommended thermofluid: Water - Monoethylene Glycol 50:50”
Operation

The tank filling capacity must be between 225 l and 245 l, so the fluid loop volume must be planned within this range.

Determines the required fluid volume and expansion volume when designing the loop.

Source
“min. filling capacity 225 l”
Installation

The pump connection is a G1 male thread, which dictates the mating fittings for the hydraulic connection.

Needed to select correct hoses and adapters for the circuit hook-up.

Source
“Pump connection G1 male”
Operation

Flow rate can be adjusted via a manual bypass valve on the back of the chiller, allowing the user to match the loop resistance.

Important for balancing the hydraulic circuit after installation.

Source
“The flow rate can be adjusted via the manual bypass valve on the backside of the chiller.”
Cumplimiento

The equipment is classified Class A, Group 1 under EN55011 for electromagnetic disturbance, which has implications for the installation environment.

Class A equipment is intended for industrial environments and may require EMC measures in residential areas.

Source
“Classification (disturbance) to EN55011: Class A, Group 1”
Installation

The unit has IP52 protection, so it is protected against dust and dripping water but not against water jets or immersion.

Constrains cleaning methods and placement relative to water sources.

Source
“Degree of Protection IP52”
Maintenance

The condenser is air-cooled with a high-efficiency fan, so adequate air flow and cleanliness around the condenser must be maintained.

Air-cooled condensers need free space and periodic cleaning to sustain cooling capacity.

Source
“Condenser in air-cooled design, performance- optimized by a built-in high-efficiency fan motor.”
Selection

The chiller has a sound pressure level of 78 dB(A) ±4 dB(A), which must be considered for the working environment.

Noise level affects placement and possible need for hearing protection or acoustic measures.

Source
“sound pressure level +/- 4 dB(A) 78 dB(A)”