Induztr
Résumé technique Visionneuse de documents Modèles associés

Cary Multicell Ambient and Peltier User's Guide

Sommaire

  1. pp. 3-4
    Table of contents listing document sections and page numbers
  2. Warning pp. 5-10
    General safety information, intended use, precautions and hazards
  3. Spec pp. 11-16
    Electrical, computer, gas and environmental specifications
  4. Procedure pp. 17-18
    Installation instructions for the multicell accessories
  5. Overview pp. 19-20
    Overview of the Cary UV-Vis flexible module
  6. Config. pp. 21-22
    System configurations and temperature probe options
  7. Overview pp. 23-25
    Instrument components, rear panel and indicator LED
  8. Procedure pp. 26-27
    Using the software and drain outlet operation
  9. Procedure pp. 28-30
    Troubleshooting, maintenance and spill handling
  10. Ordering pp. 31-32
    Spare parts list and ordering information
  11. p. 21 table, 6 rows
  12. p. 31 table, 5 rows
  13. p. 14 table, 6 rows
  14. p. 15 table, 2 rows
  15. p. 27 table, 5 rows

Table 3 Cary 3500 UV-Vis configurations

Product numberSystemProduct numberModule only
G9871ACary 3500 Compact UV-Vis SystemG9893ACary 3500 Compact Module
G9862AACary 3500 Compact Peltier UV-VisG9894ACary Compact Peltier UV-Vis Module
G9873ACary 3500 Multi UV-Vis SystemG9888ACary 3500 Multicell Module
G9866AACary 3500 Multicell Peltier UV-VisG9889ACary Multicell Peltier UV-Vis Module
G9875ACary 3500 Flexible UV Vis SystemG9886ACary UV-Vis Flexible Module
G9867AACary 3500 Multizone Peltier UV-Vis

Table 6 Spare parts for Cary 3500 UV-Vis

PartPart Number
Lamp moduleG9864-67019
Temperature probeG9889-60005
Magnetic stirrer bar PTFE star type7418000400
Flow meterK8003-60001
Purge tubing3710043100

Table 1 Computer requirements

ComponentRequirement
ProcessorIntel i5, 3.0 GHz, 18MB cache
Memory16GB RAM
Storage512 GB Solid State Drive
GraphicsIntel® UHD Graphics 770
CommunicationsPCIe GbE Controller; 2nd Serial Port Adapter, 2nd LAN NIC
Operating systemMicrosoft Windows 10 and 11 Professional and Enterprise 64-bit

Table 2 Purge gas purity requirements

Compressed gasDescription
NitrogenWater vapor <2570 ppm (dew point @ -10 °C). Acceptable sources are from bottled gas with industrial, medical or food grade nitrogen.
AirCompressed Air: ISO 8573-1:2010 CLASS 1.3.1

Table 5 Purge gas flow rate requirements

Product numberDescriptionFlow rate (LPM)
G9862AACary 3500 Compact Peltier UV-Vis5
G9866AACary 3500 Multicell Peltier UV-Vis15
G9867AACary 3500 Multizone Peltier UV-Vis15
G9894ACary Compact Peltier UV-Vis Module5
G9889ACary Multicell Peltier UV-Vis Module15

Engineering Facts

14 facts · every claim linked to a page
Safety

The lamp module contains high-voltage components and must never be disassembled; only replace it after powering off and disconnecting the engine from mains.

Prevents electric shock during lamp replacement and defines the only user-serviceable high-voltage item.

Source
“This module contains components operating at high voltages. To avoid electric shock, NEVER disassemble the module.”
Installation

Only the sample compartment and lamp module are customer-accessible; all other screwed panels must be opened only by Agilent service engineers.

Defines service boundaries and prevents unauthorized access that could void safety compliance.

Source
“Any other panels or covers that are retained by screws on the spectrophotometer and accessories may be opened ONLY by Agilent service engineers.”
Installation

Peltier-controlled models need 20 cm clearance on both sides and about 10 cm at the rear for electrical, gas connections and airflow.

Insufficient clearance causes overheating and unreliable temperature control on Peltier systems.

Source
“Allow for 20 cm (8 inches) of space on both sides and approximately 10 cm (4 inches) in the rear for electrical, gas connections and air flow.”
Installation

Non-Peltier models require 10 cm clearance on both sides and about 10 cm at the rear for electrical connections and airflow.

Ensures adequate cooling and access for ambient (non-Peltier) configurations.

Source
“Allow for 10 cm (4 inches) of space on both sides and approximately 10 cm (4 inches) in the rear for electrical connections and air flow.”
Conformité

The system requires a 3-wire earth-grounded outlet; a separate receptacle per unit is recommended and extension cords or adapters are not recommended.

Grounding is mandatory to avoid shock hazard and to meet electrical safety requirements.

Source
“A 3-wire outlet with ground connection must be provided for the Cary system.”
Selection

Peltier modules require dry, oil-free, particle-free, non-combustible compressed gas (nitrogen or air) to prevent condensation at sub-ambient temperatures.

Gas quality directly affects condensation prevention and optical surface protection.

Source
“The supplied gas must be dry, oil and particle free and non-combustible.”
Operation

Multicell Peltier zones can be set from -5 to 110 °C and controlled by cell holder (block) or sample temperature via the probe accessory.

Defines the usable temperature range and control mode for thermal applications.

Source
“the temperature of each zone can be varied over a range of -5 to 110 °C”
Safety

The sample compartment and cuvettes can remain hot after operation; allow at least five minutes cooling before removing cuvettes.

Prevents burns during routine sample handling on heated Peltier modules.

Source
“Allow the sample compartment and cuvettes to cool for at least five minutes before attempting to remove cuvettes.”
Safety

The Flexible module contains strong magnets; keep at least 145 mm away from devices and objects that could be damaged, and follow AIMD manufacturer guidance.

Protects pacemakers, storage media and electronics from magnetic field damage.

Source
“Keep magnets at least 145 mm away from devices and objects that could be damaged by strong magnetic fields.”
Installation

The purge kit maximum pressure is 689 kPa (100 PSIG); always use an appropriate regulator and gauge to maintain correct purge pressure.

Prevents over-pressurizing the module and ensures stable purge flow.

Source
“The operating pressure of the Agilent supplied gauge is up to a maximum of 689 kPa (100 PSIG).”
Installation

Use clean flexible PVC (or equivalent) 6 mm OD/4 mm ID tubing; never use rubber tubing because talc can be blown into the optical system.

Rubber tubing contaminates optics and degrades photometric performance.

Source
“Never use rubber tubing, because it may be treated internally with talc that can be blown into the optical system.”
Installation

Never connect gas directly to the module; always use a pressure regulator meeting the manual specifications.

Direct connection risks overpressure damage to the module and seals.

Source
“Never connect the gas directly to the module. Always use a pressure regulator that meets the specifications listed in this manual.”
Maintenance

Multicell and Compact modules require a drain vessel and tubing over the 6 mm OD drain outlet; the user must supply a chemically inert container of at least 2 liters.

Prevents spilled liquids from reaching the benchtop and ensures safe waste collection.

Source
“A chemically inert container, not glass or of a narrow-necked style, to hold a minimum of 2 liters (4 pints) of waste must be provided by the user.”
Maintenance

Replace blown fuses only with the type and rating indicated on the rear of the instrument; other internal fuses are not operator-accessible.

Wrong fuse rating reduces safety protection and may cause fire.

Source
“replace the blown fuse with one of the type and rating as indicated in the on the rear of the instrument.”